Volkswagen Jetta / Jetta Hybrid. Manual — part 40
sunroof glass panel
1.4.1
Removing
Carry out following work:
– Push sliding headliner to rear.
– Raise sliding/tilting sunroof
– Unclip bellows along lower strip.
– Loosen the two front catches and push bellows backwards out
of guide -arrow-.
– Move glass panel to zero position.
– Remove bolts -1- and -3-
– Loosen bolt -2- by turning it a few times (do not unscrew com‐
pletely).
– Take out glass panel upwards out of roof cut-out.
1.4.2
Installing
Carry out following work:
• Guide pins -1- must align with markings -arrow- on left and
right guide plates.
If this is not the case, adjust parallel running
⇒ page 160
.
– Insert glass panel from above into roof cut-out.
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
1. Sunroof with glass panel
157
– Carry out height-adjustment of glass panel
⇒ page 158
.
1.5
Height-adjustment of glass panel
Carry out following work:
Bellows not yet removed.
– Push sliding headliner to rear.
– Raise sliding/tilting sunroof
– Unclip bellows along lower strip.
– Loosen the two front catches and push bellows backwards out
of guide -arrow-.
– Move glass panel to zero position.
Continued for all vehicles:
– Loosen bolts -1...3- (do not unscrew completely).
– To prevent wind noises, carry out front and rear height adjust‐
ment in accordance with illustrations.
Height-adjustment of glass panel at front (-arrow- points in direc‐
tion of travel).
-a- = 0…1 mm lower than roof line
– Tighten front bolts for glass panel.
Specified torque of bolts: 7 Nm
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
158
-b- = 0…1 mm higher than roof line
– Tighten rear bolt for glass panel.
– Tighten middle bolt for glass panel.
Specified torque of bolts: 7 Nm
– Raise sliding/tilting sunroof
– Press bellows into mounts of guide plate.
– Clip bellows into assembly frame.
1.6
Checking parallel running of glass panel
Carry out following work:
– Push sliding headliner to rear.
– Raise sliding/tilting sunroof
– Unclip bellows along lower strip.
– Loosen the two front catches and push bellows backwards out
of guide -arrow-.
– Move glass panel to zero position.
• Guide pins -1- must align with markings -arrow- on left and
right guide plates.
If this is not the case, adjust parallel running
⇒ page 160
.
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
1. Sunroof with glass panel
159
Note
Parallel running can only be adjusted if sliding/tilting sunroof drive
and glass panel have been removed (in "0" position).
Carry out following work:
– Remove glass panel
⇒ page 157
.
– Removing sunroof drive
⇒ page 162
.
– Move guide plates on both sides by hand until guide pin -1- is
aligned with marking -arrow- on guide plate.
– Adjust and install sliding/tilting sunroof drive
⇒ page 162
.
– Install glass panel
⇒ page 157
.
1.8
Renewing panel seal
Carry out following work:
– Remove glass panel
⇒ page 157
.
– Pull seal -1- off glass panel -2-.
– Press new seal into groove in glass panel -2-.
Note
To ease fitting of seal, coat panel edge with a soapy solution.
1.9
Removing and installing wind deflector
1.9.1
Removing
Carry out following work:
– Open sunroof completely.
– Remove carrier unit
⇒ page 165
.
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
160
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст