Volkswagen Jetta Hybrid (2013 year). Manual — part 18
⇒ “2.1 Removing gearbox”, page 65
⇒ “2.2 Installing gearbox”, page 69
⇒ “2.3 Specified torques for gearbox”, page 72
2.1
Removing gearbox
10 ; Removing and installing engine; Removing engine .
Remove gearbox from engine as follows:
Special tools and workshop equipment required
♦ Bits XZN 12 -T10099-
♦ Socket -T10061-
♦ Shackle -10 - 222 A /12-
Jetta Hybrid 2013 ➤
2. Removing and installing gearbox
65
scissor-type assembly platform -VAS 6131- .
– Disconnect connector -1- from selector valve -2- of mecha‐
tronic unit and pull wiring harness off retainer on front of
gearbox.
– Remove high-voltage wiring harness for drive motor -PX2- to‐
gether with terminal box -1- from gearbox ⇒ Electrical system,
and installing high-voltage wiring harness for drive motor -
PX2- .
– Also remove cable retainer -1- for high-voltage wiring harness
for drive motor -PX2- from gearbox -arrows- ⇒ Electrical sys‐
tem, hybrid vehicles; Rep. gr. 93 ; High-voltage cables; Re‐
moving and installing high-voltage wiring harness for drive
motor -PX2- .
Jetta Hybrid 2013 ➤
66
– Remove vacuum pump for brakes -V192- -B- together with
bracket from gearbox and tie it up to side of engine.
– Release and disconnect connector -D- from drive motor rotor
position sender 1 -G713- -C-.
– Unscrew bolts -arrows- and pull out drive motor rotor position
sender 1 -G713- .
WARNING
Risk of soiling.
Thoroughly clean all joints and surrounding areas before dis‐
mantling.
In the procedure below the hydraulic system of the mecha‐
tronic unit will be opened. Soiling will cause the system to fail!
– Unscrew union nut -1- for hydraulic line -3- from engine.
– Then, pull retaining clip -2- out of valve block/mechatronic unit.
– Pull hydraulic line -3- simultaneously out of engine and valve
block/mechatronic unit.
• Seal hydraulic line connections immediately with suitable seal‐
ing plugs to ensure that as much hydraulic fluid as possible
remains in the hydraulic line.
• Also seal the connections on engine and valve block/mecha‐
tronic unit with suitable sealing plugs.
• For allocation of sealing plugs and hydraulic fluid refer to ⇒
Electronic parts catalogue “ETKA” .
– Unscrew bolts -1 ... 7- securing gearbox on engine.
Note
♦
For unscrewing bolts -3- and -4- bits XZN 12 -T10099/1- can
be used.
♦
Bolts -8- and -9- are left screwed in.
– Screw guide pins -T10515- into engine as shown in illustration.
Note
For reasons of clarity, the gearbox is removed in the illustration.
Jetta Hybrid 2013 ➤
2. Removing and installing gearbox
67
-T10061- . Note coolant line -A- while doing so.
– Press gearbox off dowel sleeves in engine.
– Carefully pull gearbox off engine. Ensure to not damage con‐
nections -arrow 1- on electric drive motor -V141- and the drive
motor temperature sender -G712- -arrow 2- while doing so.
Note
If necessary, change position of gearbox using spindles of gear‐
box support -3282- while pulling gearbox off engine.
If gearbox is to be sent:
– Remove bracket -A- at front of gearbox -arrows-.
Jetta Hybrid 2013 ➤
68
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст