Jeep Cherokee (2019 year). Manual — part 34

Setting Name

Selectable Options

Forward Collision Warning

Plus (FCW+) Sensitivity — If

Equipped

Far

Med

Near

NOTE:
The “Forward Collision Warning Plus (FCW+) Sensitivity” setting determines at what relative distance the vehicle
directly in front of you needs to be at, before the system will warn you of a possible collision with the vehicle directly
in front of you, based on the option is selected. “Far” will give you the most amount of reaction time, whereas
“Near” will give you the least amount of reaction time, based on the distance between the two vehicles.

Forward Collision Warning

Plus (FCW+) — If Equipped

Off

Warning Only

Warning and Brake

NOTE:
The “Forward Collision Warning Plus (FCW+)” setting includes Advanced Brake Assist (ABA). The ABA applies ad-
ditional brake pressure when the driver requests insufficient brake pressure to avoid a potential frontal collision.
When the “Sound Only” option is selected a chime will sound alerting you of a possible collision with the vehicle in
front of you and more brake pressure is needed. When the “Sound and Brake” option is selected, it will apply the
brakes to slow your vehicle in case of potential forward collision and sound an audible chime to alert you.

ParkSense — If Equipped

Sound Only

Sound and Display

Rear ParkSense Volume — If

Equipped

Low

Medium

High

Front ParkSense Volume —

If Equipped

Low

Medium

High

532

MULTIMEDIA

Setting Name

Selectable Options

Side Distance Warning

Off

Sound Only

Sound and Display

Side Distance Warning Vol-

ume

Low

Med

High

LaneSense Warning — If

Equipped

Early

Medium

Late

NOTE:
The “LaneSense Warning” setting determines at what distance the LaneSense system will warn you, through steering
wheel feedback, of a possible lane departure.

LaneSense Strength — If

Equipped

Low

Medium

High

Blind Spot Alert — If

Equipped

Off

Lights

Lights and Chime

NOTE:
If your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is not damaged,
the sensor may have become misaligned. Take your vehicle to an authorized dealer to verify sensor alignment. A sen-
sor that is misaligned will result in the Blind Spot Monitor (BSM) not operating to specification.
Rain Sensing Auto Wipers —

If Equipped

On

Off

10

MULTIMEDIA

533

Lights

After pressing the “Lights” button on the touchscreen, the
following settings will be available:

Setting Name

Selectable Options

Headlight Sensitivity — If

Equipped

Level 1: minimum

sensitivity

Level 2: medium

sensitivity

Level 3: maximum sensitivity

NOTE:
The greater the sensitivity set, the less the external light variation required to turn on the lights (e.g. with a setting on
level 3 at sunset the headlights turn on earlier than in levels 1 and 2).

Headlight Off Delay

0 sec

30 sec

60 sec

90 sec

NOTE:
When the “Headlight Off Delay” feature is selected, it allows the adjustment of the amount of time the headlights
remain on after the engine is shut off.

Greeting Lights

On

Off

Automatic High Beam Head-

lamps — If Equipped

On

Off

Daytime Running Lights

On

Off

Cornering Lights

On

Off

NOTE:
When the “Cornering Lights” feature is selected, if the steering wheel rotation angle is large or the turn signal indica-
tors are on, a light (incorporated in the fog light) will turn on, on the relevant side to improve visibility at night.

534

MULTIMEDIA

Setting Name

Selectable Options

Flash Lights With Lock — If

Equipped

On

Off

Interior Ambient Lights

+

-

NOTE:
The “Interior Ambient Lights” setting can also be adjusted by selecting any point on the scale between the “+” and
“-” buttons on the touchscreen.

Doors & Locks

After pressing the “Doors & Locks” button on the touch-
screen, the following settings will be available:

Setting Name

Selectable Options

Auto Unlock On Exit

On

Off

NOTE:
When this feature is selected, all doors will unlock when the vehicle is stopped and the transmission is in the PARK
or NEUTRAL position and the driver’s door is opened.

Flash Lights With Lock

On

Off

Horn With Lock

On

Off

Horn With Remote Start — If

Equipped

On

Off

10

MULTIMEDIA

535

Setting Name

Selectable Options

Remote Door Unlock/Door Unlock

Driver

All

NOTE:
When “Driver” is selected, only the driver’s door will unlock on the first push of the key fob unlock button, you
must push the key fob unlock button twice to unlock the passenger’s doors. When “All” is selected, all of the doors
will unlock on the first press of the key fob unlock button. If “All” is programmed, all doors will unlock no matter
which Passive Entry equipped door handle is grasped. If “Driver” is programmed, only the driver’s door will unlock
when the driver’s door is grasped. Touching the handle more than once will only result in the driver’s door opening
once. If the driver’s door is opened, the interior door lock/unlock switch can be used to unlock all doors (or use key
fob).

Memory Linked To FOB — If

Equipped

On

Off

NOTE:
This feature provides automatic recall of all settings stored to a memory location (driver’s seat, exterior mirrors, steer-
ing column position and radio station pre-sets) to enhance driver mobility when entering and exiting the vehicle.

536

MULTIMEDIA

Auto Comfort Systems — If Equipped

After pressing the “Auto-On Comfort Systems” button on
the touchscreen, the following settings will be available:

Setting Name

Selectable Options

Auto-On Driver Heated/Ventilated Seat & Steering

Wheel With Vehicle Start — If Equipped

Off

Remote Start

All Starts

NOTE:
When this feature is selected, the driver’s heated seat and heated steering wheel will automatically turn on when tem-
peratures are below 40° F (4.4° C). When temperatures are above 80° F (26.7° C), the driver vented seat will turn on.

Engine Off Options

After pressing the “Engine Off Options” button on the
touchscreen, the following settings will be available:

Setting Name

Selectable Options

Headlight Off Delay

0 sec

30 sec

60 sec

90 sec

NOTE:
When this feature is selected, it allows the adjustment of the amount of time the headlights remain on after the en-
gine is shut off.

Radio Off Delay

0 min

20 min

NOTE:
When this feature is selected, the radio will stay on for a preset time after the ignition key is turned to STOP/OFF.

10

MULTIMEDIA

537

Audio

After pressing the “Audio” button on the touchscreen, the
following settings will be available:

Setting Name

Selectable Options

Equalizer

Bass

Mid

Treble

NOTE:
When in this display you may adjust the “Bass”, “Mid”, and “Treble” settings. Adjust the settings with the “+” and
“–” setting buttons on the touchscreen or by selecting any point on the scale between the “+” and “–” buttons on the
touchscreen. Bass/Mid/Treble also allow you to simply slide your finger up or down to change the setting as well as
press directly on the desired setting.

Balance/Fade

Up Arrow

Button

Down Ar-

row Button

Left Arrow

Button

Right Ar-

row Button

Center “C”

Button

NOTE:
When in this display you may adjust the “Balance/Fade” of the audio by using the “Arrow” button on the touch-
screen to adjust the sound level from the front and rear or right and left side speakers. Press the “Center ‘C’ Button”
on the touchscreen to reset the balance and fade to the factory setting.

Speed Adjusted Volume

Off

1

2

3

Surround Sound — If Equipped

On

Off

Loudness

On

Off

NOTE:
The “Loudness” feature improves sound quality at lower volumes when enabled.

538

MULTIMEDIA

Setting Name

Selectable Options

AUX Volume Offset — If Equipped

+

-

NOTE:
The “AUX Volume Offset” feature provides the ability to tune the audio level for portable devices connected through
the AUX input.

Phone/Bluetooth

After pressing the “Phone/Bluetooth” button on the touch-
screen, the following settings will be available:

Setting Name

Selectable Options

Paired Phones

List of Paired Phones

NOTE:
This feature shows which phones are paired to the Phone/Bluetooth system. For further information, refer to the
Uconnect Owner’s Manual Supplement.

10

MULTIMEDIA

539

SiriusXM Setup — If Equipped

After pressing the “SiriusXM Setup” button on the touch-
screen, the following settings will be available:

Setting Name

Selectable Options

Channel Skip

List of Channels

NOTE:
SiriusXM can be programmed to designate a group of channels that are the most desirable to listen to or to exclude
undesirable channels while scanning. This feature allows you to select the channels you would like to skip.

Subscription Info

Sirius ID

NOTE:
New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your
radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription
Information screen to re-subscribe.

1. Press the “Subscription Info” button on the touchscreen to access the Subscription Information screen.

2. Write down the Sirius ID numbers for your receiver. To reactivate your service, either call the number listed on the

screen or visit the provider online.

540

MULTIMEDIA

Restore Settings

After pressing the “Restore Settings” button on the touch-
screen, the following settings will be available:

Setting Name

Selectable Options

Restore Settings

OK

Cancel

NOTE:
When the “Restore Settings” feature is selected, it will reset all settings to their default settings.

Clear Personal Data

After pressing the “Clear Personal Data” button on the
touchscreen, the following settings will be available:

Setting Name

Selectable Options

Clear Personal Data

OK

Cancel

NOTE:
When the “Clear Personal Data” feature is selected it will remove all personal data including Bluetooth devices and
presets.

10

MULTIMEDIA

541

Customer Programmable Features — Uconnect 4
Personal Settings

Press the “Apps

” button, then press the “Settings”

button on the touchscreen to display the menu setting
screen. In this mode the Uconnect system allows you to
access programmable features that may be equipped
such as Display, Units, Voice, Clock, Safety & Driving
Assistance, Lights, Doors & Locks, Auto-On Comfort,
Engine Off Options, Audio, Phone/Bluetooth, SiriusXM
Setup, Restore Settings, Clear Personal Data, and Sys-
tem Information.

NOTE:

Only one touchscreen area may be selected at a

time.

When making a selection, press the button on the touch-
screen to enter the desired mode. Once in the desired
mode, press and release the preferred setting and make
your selection. Once the setting is complete, either press
the Back Arrow/Done button on the touchscreen or the
Back button on the faceplate to return to the previous menu
or press the “X” button on the touchscreen to close out of
the settings screen. Pressing the “Up” or “Down” Arrow
buttons on the right side of the screen will allow you to
toggle up or down through the available settings.

NOTE:

All settings should be changed with the ignition in

the RUN position.

Uconnect 4 With 7–inch Display Buttons On Touchscreen

And Buttons On Faceplate

1 — Uconnect Buttons On The Touchscreen
2 — Uconnect Buttons On The Faceplate

542

MULTIMEDIA

Language

After pressing the “Language” button on the touchscreen,
the following settings will be available:

Setting Name

Selectable Options

Language

English

Espanol

Francais

Display

After pressing the “Display” button on the touchscreen, the
following settings will be available:

Setting Name

Selectable Options

Display Mode

Auto

Manual

Display Brightness With

Headlights ON

+

-

NOTE:
To make changes to the

⬙Display Brightness with Headlights ON⬙ setting, the headlights must be on and the interior

dimmer switch must not be in the

⬙party⬙ or ⬙parade⬙ positions.

Display Brightness With

Headlights OFF

+

-

NOTE:
To make changes to the

⬙Display Brightness with Headlights OFF⬙ setting, the headlights must be off and the interior

dimmer switch must not be in the

⬙party⬙ or ⬙parade⬙ positions.

10

MULTIMEDIA

543

Setting Name

Selectable Options

AutoShow Smartphone Dis-

play Upon Connection

On

Off

Touchscreen Beep

On

Off

Control Screen Time-Out —

If Equipped

On

Off

Units

After pressing the “Units” button on the touchscreen, the
following settings will be available:

Setting Name

Selectable Options

Units

US

Metric

Custom

NOTE:
The “Custom” option allows you to set the “Speed” (MPH, or km/h), “Distance” (mi, or km), “Fuel Consumption”
[MPG (US), MPG (UK), L/100 km, or km/L], “Pressure” (psi, kPa, or bar), and “Temperature” (°C, or °F) units of
measure independently.

544

MULTIMEDIA

Voice
After pressing the “Voice” button on the touchscreen, the following settings will be available:

Setting Name

Selectable Options

Voice Response Length

Brief

Detailed

Show Command List

Never

With Help

Always

Clock
After pressing the “Clock” button on the touchscreen, the following settings will be available:

Setting Name

Selectable Options

Sync With GPS Time

Set Time Hours

+

-

Set Time Minutes

+

-

Time Format

12 hour

24 hour

AM

PM

NOTE:
Within the “Set Time and Format” setting, press the corresponding arrow buttons on the touchscreen to adjust to the
correct time.

Show Time in Status Bar

Set Date — If Equipped

Up Arrow

Down Arrow

NOTE:
Within the “Set Date” setting, press the corresponding arrow buttons on the touchscreen to adjust to the correct date.

10

MULTIMEDIA

545

Safety/Assistance

After pressing the “Safety/Assistance” button on the
touchscreen, the following settings will be available:

Setting Name

Selectable Options

ParkSense — If Equipped

Sound

Sound and Display

NOTE:
The “ParkSense” system setting will scan for objects behind the vehicle when the transmission gear selector is in RE-
VERSE and the vehicle speed is less than 7 mph (11 km/h), when enabled. It will provide an alert (audible and/or vi-
sual) to indicate the proximity to other objects. The system can be enabled with “Sound Only,” or “Sound and Display.”

Rear ParkSense Volume

Low

Med

High

Rear ParkSense Braking

Assist — If Equipped

NOTE:
When the “Rear ParkSense Braking Assist” feature is selected, the park assist system will detect objects located be-
hind the vehicle and utilize autonomous braking to stop the vehicle.

546

MULTIMEDIA

Setting Name

Selectable Options

Blind Spot Alert — If

Equipped

Off

Lights

Lights and Chime

ParkView Backup Camera

Delay — If Equipped

NOTE:
The “ParkView Backup Camera Delay” setting determines whether or not the screen will display the rear view image
with dynamic grid lines for up to ten seconds after the vehicle is shifted out of REVERSE. This delay will be canceled
if the vehicle’s speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, or the ignition is switched to
the OFF position.

Active ParkView Camera

Guidelines

NOTE:
The “Active ParkView Camera Guidelines” feature overlays the Rear Backup Camera image with active, or dynamic,
grid lines to help illustrate the width of the vehicle and its project back up path, based on the steering wheel position
when the option is checked. A dashed center line overlay indicates the center of the vehicle to assist with parking or
aligning to a hitch/receiver.

Fixed ParkView Backup

Camera Guidelines

Hill Start Assist — If

Equipped

10

MULTIMEDIA

547