Kia Carnival (2009+). Instruction — part 448
Turn Signal And Side Repeater Lamps Function
1. Necessary conditions to switch ON(if they are standard) :
A. By activation of Crash Unlock
B. During the opening / closing of the Tail gate by the PTG Flasher input
C. With the Remote Keyless Entry to lock / unlock the vehicle
D. By alarm activation
E. By panic activation with the Remote Keyless Entry
F. By activation of the Hazard Lamp by the hazard switch and ignition is position OFF, ACC or RUN
G. By using the turn lever switch with the ignition switch in the ON position.
2. Necessary conditions to switch OFF(if they are standard) :
A. Ignition switch in OFF position for deactivation of crash unlock flashing
B. Deactivation of the alarm or at the end of the alarm flashing sequence
C. Deactivation of panic sequence with pushing any button of the Remote Keyless Entry or at the end of the panic
flashing sequence
D. Turn lever switch command in OFF postion or ignition switch in OFF, ACC or START position to stop turn lever
flashing.
E. The hazard switch in OFF position or ignition switch in position START to stop the Hazard flashing.
F. At the end of the Lock, Unlock and PTG flashing sequence.
3. During the start up of the vehicle (ignition key in position START) :
A. The Turn signal lamps activated by the turn lever switch are temporarily turned OFF. If the time duration in Start
position is more than 10seconds and engine running, the Turn signal lamps are managed again as if the ignition
key was in ON position,
B. The flashing sequence of the hazard lamps is immediately stopped if they have been activated by the hazard
button. If the time duration in Start position is more than 10seconds and engine running, the flashing sequence
of the hazard lamps are managed again as if the ignition key was in RUN position,
C. The flashing sequence of the hazard lamps is not stopped if they have been activated by a crash unlock.
4. Functional diagram
Front Fog Lamps Function
1. Necessary conditions to switch ON :
A. By using the stalk: Head lamp switch in position 'Head lamp Low Beam' and Front Fog lamp sw ON
B. When Auto light function activated and Auto light Sensor signal status is 'HL ON' and Front Fog lamp sw ON
2. Necessary conditions to switch OFF :
A. When Auto light function activated and Auto light Sensor signal status is not ON
B. When Front fog lamp sw OFF.
3. Functionnal Diagram
Backup Lamps Function
1. Necessary conditions to switch ON :
A. When inhibit sw 'R' read by FAM is active and transmitted to RAM by CAN signal.
2. Necessary conditions to switch OFF :
A. When inhibit sw 'R' read by FAM is not active and transmitted to RAM by CAN signal.
3. Functional diagram
Stop Lamps Function
1. Necessary conditions to switch ON the stop lamps:
A. Pushing on the brake pedal.
2. Necessary conditions to switch OFF the stop lamps:
A. Releasing the brake pedal.
3. Functional diagram
Auto Light Function
1. The Auto light function is active when the Head lamp switch is positioned to 'Auto' and the Key is in RUN position.
The auto light sensor is powered on the status ACC, START and RUN of the key position. Based on the Auto light
sensor values corresponding to the exterior brightness level, it controls automatically the lighting of the Park and tail
lamps or / and the Head lamps Low Beam depending on the country.
2. Auto light Sensor detection table
Mode
Tail Lamps
Head Lamps Low Beam
Lux (Lux)
Voltage(V)
Lux (Lux)
Voltage(V)
ON
< 24 ± 5.2
<1.77 ± 0.08V
Same as Tail lamps
OFF
> 48 ± 10.5
> 3.47 ± 0.1V
Same as Tail lamps
Drl Function
1. The Auto DRL function operates the Head lamps High Beam at 50% of full illumination.
The park and tail are managed by the auto light sensor.
The Auto DRL function is active if:
A. The ignition switch is on RUN position
B. The engine is running.
C. The Park brake switch is OFF.
2. The DRL function is inactive when one of above conditions is released.
When the DRL function is active, the Head lamps High Beam can't be turned ON, except for the Flash To Pass
activation.
activation.
3. Functional diagram
Battery Saver Function
1. Necessary conditions to activate the Battery Saver function:
A. Do not turn off the Park/Tail Lamp when intentionally turned on.
B. If Key reminder switch is ON and Park/Tail Lamp switch is ON, Intentional "ON" should be reset
C. If the driver's door is open and if the key is not in the key hole whereas the Head lamp switch is still in position
'Park and tail lamp' or 'Head lamp Low Beam', the park and tail lamps (and the Front fog lamps if turned on)
are immediately turned off.
2. Necessary conditions to cancel the Battery Saver function:
A. As soon as the Key is input into the IGN Key Cylinder or the Head lamp switch is put to position OFF.
3. Functional diagram
Escort Function
1. If the head lamps low beam are turned on by head lamps low beam switch or by auto light switch when the Ignition
switch is turned from the ON to ACC or OFF positions.
2. The head lamps low beam are turned off:
A. 30s after the driver door is closed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст