Kia Sedona (2008 year). Instruction — part 161
DTC B1646 doesn't show up by itself. It means that there's any fault in
Multifunction switch signal (light, wiper)
CAN Communication line
FAM, RAM
so, B1646 show up with DTC B1603, B1611, B1612, B1950 and if these problems are solved, it
disappear automatically.
YES
Go to COMPONENT INSPECTION procedure.
NO
Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and
ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending,
corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to
"VERIFICATION OF VEHICLE REPAIR" procedure.
COMPONENT INSPECTION
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Erase the DTC.
4. Is the DTC erased?
YES
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or
damage. Repair or replace as necessary and then go to "VERIFICATION OF VEHICLE REPAIR"
procedure.
NO
Refer diagnosis guide of accompanied DTC.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B1102.
DTC B1647 VAS ERROR
COMPONENT LOCATION
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 113
© 2006 Mitchell Repair Information Company, LLC.
Fig. 86: Locating VAS Switch
Courtesy of KIA MOTORS AMERICA, INC.
GENERAL DESCRIPTION
VAS gives warning to driver when major problem of vehicle occurs, when VAS operating condition, IPM
transmits `mute' signal to AV head unit to make speaker be in waiting mode, then IPM translate sound signal
from external amp to speaker through CMD relay, warning items of VAS are seatbelt, charging voltage,
sunroof, PSD/PTG, fuel shortage and VAS operates only when IG and VAS switch is "ON".
DTC DESCRIPTION
The ECM sets DTC B1647 if VAS doesn't operate within 5sec after VAS operation signal is transmitted.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
MONITOR DTC STATUS
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Select "Diagnostic Trouble Codes (DTC s)" mode and monitor "DTC Status" parameter.
4. Is the DTC B1647 present?
YES
Item
Detecting Condition
Possible Cause
DTC Strategy
Check time lag. (time between VAS operation signal
and VAS operation)
Faulty IPM
Enable Conditions
IGN: ON, VAS switch: ON
Threshold value
5 sec
Detecting time
-
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 114
© 2006 Mitchell Repair Information Company, LLC.
Go to COMPONENT INSPECTION procedure.
NO
Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and
ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending,
corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to
"VERIFICATION OF VEHICLE REPAIR" procedure.
COMPONENT INSPECTION
1. Check IPM
1. Check regional properties of IPM.
2. Dose regional properties of IPM valid?
YES
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage.
Repair or replace as necessary and then go to "VERIFICATION OF VEHICLE REPAIR"
procedure.
NO
Substitute with a known-good IPM and check for proper operation. If the problem is corrected,
replace IPM and then go to "VERIFICATION OF VEHICLE REPAIR" procedure.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B1102.
DTC B1910 LEFT OSM HORIZONTAL MOTOR OR SENSOR ERROR
COMPONENT LOCATION
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 115
© 2006 Mitchell Repair Information Company, LLC.
Fig. 87: Locating DDM, Front Door Key Switch & Power Window Motor
Courtesy of KIA MOTORS AMERICA, INC.
GENERAL DESCRIPTION
DDM is a node of CAN communication system which consists of IPM. FAM, RAM, ADM, IMS. Main
function of DDM is lock/unlock of door and window, adjusting position and fold/unfold of outside mirror.
Outside mirror module consists of motor and position sensor. According to Outside mirror Switch signal,
Outside mirror motor adjusts position of mirror and position sensor delivers result to DDM by voltage value.
DTC DESCRIPTION
The ECM sets DTC B1910 if signal voltage of left outside mirror horizontal sensor is out of range.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
MONITOR DTC STATUS
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Select "Diagnostic Trouble Codes (DTC s)"mode and monitor "DTC Status" parameter.
4. Is the DTC B1910 present?
Item
Detecting Condition
Possible Cause
DTC Strategy
Check Voltage
Open or short in signal
harness
Open or short in power
harness
Faulty outside mirror motor
Faulty outside mirror sensor
Faulty DDM
Enable Conditions
IGN `ON' & Engine `OFF'
Threshold value
1.04V < Output voltage <
3.95V
Detecting time
50 ms
FAIL SAFE
-
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:17 PM
Page 116
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст