Kia Sedona (2008 year). Instruction — part 260
Fig. 182: Checking Voltage Between Terminal "19" And "20" Of A/C Control Unit
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured voltage within specifications?
YES
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage. Repair or replace as necessary and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
NO
Substitute with a known-good A/C Control Unit and check for proper operation.
If the problem is corrected, replace A/C Control Unit and then go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
VERIFICATION OF VEHICLE REPAIR
After a repair, it is essential to verify that the fault has been corrected.
1. Connect scan tool and select "Diagnostic Trouble Codes (DTCs)" mode and then clear DTC.
2. Operate the vehicle and monitor the DTC on the scan tool.
3. Are any DTCs present?
YES
Go to the applicable troubleshooting procedure.
NO
System is performing to specification at this time.
DTC B2415 AIR MIX MOTOR (PASSENGER)
COMPONENT LOCATION
2008 Kia Sedona EX
2008 HVAC Blower & A/C Controls (Automatic) - Sedona
Microsoft
Monday, May 24, 2010 3:56:09 PM
Page 162
© 2006 Mitchell Repair Information Company, LLC.
Fig. 183: Identifying Temperature Control Actuator Component Location
Courtesy of KIA MOTORS AMERICA, INC.
GENERAL DESCRIPTION
Temperature control actuator located at heater unit, regulates the temperature by the procedure as follows.
Signal from control unit adjusts position of temp, door by operating temp, motor and then temperature will be
regulated by the hot/cold air ratio decided by position of temp. door.
DTC DESCRIPTION
The A/C controller sets DTC B2415 if the air mix actuator doesn't move to intended position within 40 sec (In
this case, A/C controller try to move temp, door for 2 sec. 3 times, every 20 sec. before setting DTC).
DTC DETECTING CONDITION
DTC DETECTING CONDITION CHART
SPECIFICATION
Item
Detecting Condition
Possible cause
DTC Strategy
Voltage check
Poor connection of connected part
Open circuit in harness
Short circuit in harness
Faulty driver Air Mix potentiometer
Fault A/C Control Unit
Threshold value
< 0.1V
Detecting time
0.3 sec
FAIL SAFE
-
2008 Kia Sedona EX
2008 HVAC Blower & A/C Controls (Automatic) - Sedona
Microsoft
Monday, May 24, 2010 3:56:09 PM
Page 163
© 2006 Mitchell Repair Information Company, LLC.
Fig. 184: Air Mix Graph
Courtesy of KIA MOTORS AMERICA, INC.
MONITOR SCAN TOOL DATA
1. Connect scan tool to Data Link Connector (DLC).
2. Engine "ON"
3. Monitor the "Passenger Air Mix Potentiometer" Parameter on the scan tool while operating temp, switch.
Fig. 185: Diagnosis Function Screen Display - Air Mix Potentiometer (Pa)
Courtesy of KIA MOTORS AMERICA, INC.
4. Are the DTC B2415 present and is parameter of "Passenger AIR MIX Potentiometer" fixed?
There is any fault in Passenger AIR MIX Motor. If the parameter of "Passenger AIR MIX DOOR" is 30%
or less when the actuator operates to the hot position, or If the parameter is 60% and more when the
actuator operates to the cold position.
YES
2008 Kia Sedona EX
2008 HVAC Blower & A/C Controls (Automatic) - Sedona
Microsoft
Monday, May 24, 2010 3:56:09 PM
Page 164
© 2006 Mitchell Repair Information Company, LLC.
Go to TERMINAL AND CONNECTOR INSPECTION procedure.
NO
Fault is intermittent caused by poor contact in the sensor's and/or A/C controller's connector or was
repaired and A/C controller memory was not cleared. Thoroughly check connectors for looseness, poor
connection, bending, corrosion, contamination, deterioration, or damage. Repair or replace as necessary
and then go to "VERIFICATION OF VEHICLE REPAIR" procedure.
TERMINAL AND CONNECTOR INSPECTION
1. Many malfunctions in the electrical system are caused by poor harness and terminals.
Faults can also be caused by interference from other electrical systems, and mechanical or chemical
damage.
2. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination,
deterioration, or damage.
3. Has a problem been found?
YES
Repair as necessary and go to "VERIFICATION OF VEHICLE REPAIR" procedure.
NO
Go to "SIGNAL CIRCUIT INSPECTION" procedure.
SIGNAL CIRCUIT INSPECTION
1. Check for open in harness.
1. Ignition "OFF"
2. Disconnect Passenger Air Mix potentiometer.
3. Measure resistance between terminal "3, 4" of Passenger Air Mix Motor and terminal "10, 13" of
A/C control unit.
Specification: Approx. 0 ohms
2008 Kia Sedona EX
2008 HVAC Blower & A/C Controls (Automatic) - Sedona
Microsoft
Monday, May 24, 2010 3:56:09 PM
Page 165
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст