Kia Sedona (2008 year). Instruction — part 228
4. Is the measured resistance within specifications?
YES
Go to "POWER CIRCUIT INSPECTION" procedure.
NO
Check for short to ground in signal harness. Repair as necessary and go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
POWER SUPPLY CIRCUIT INSPECTION
1. Check for short or short in harness.
1. Ignition "ON"
2. Connect Driver Direction potentiometer.
3. Measure voltage between terminal "5" of Driver Direction potentiometer and chassis ground.
Specification: Approx. 5V
Fig. 39: Checking Voltage Between Terminals Of Driver Direction Potentiometer And
Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured voltage within specifications?
YES
Go to "COMPONENT INSPECTION" procedure.
NO
Check for short or open in power harness. Repair as necessary and go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
COMPONENT INSPECTION
2008 Kia Sedona EX
2008 HVAC Blower & A/C Controls (Automatic) - Sedona
Microsoft
Monday, May 24, 2010 3:56:07 PM
Page 34
© 2006 Mitchell Repair Information Company, LLC.
1. Check actuator.
1. Ignition "OFF"
2. Disconnect Driver Direction potentiometer.
3. Verify that the mode actuator operates to the vent mode when connecting 12V to the terminal "3"
and grounding terminal "4".
4. Verify that the mode actuator operates to the def mode when the connections are reversed.
Fig. 40: Checking Terminal 3 And Grounding Terminal 4
Courtesy of KIA MOTORS AMERICA, INC.
5. Does the actuator work properly?
YES
Go to step 2.
NO
Substitute with a known-good actuator and check for proper operation. If the problem is corrected,
replace actuator and then go to "VERIFICATION OF VEHICLE REPAIR" procedure.
2. Check potentiometer
1. Ignition "ON"
2. Connect Driver Direction potentiometer.
3. Measure voltage between terminal "6" and "7" of Driver Direction potentiometer as the mode
switch is operated.
Specification: Refer to DOOR POSITION CHART
2008 Kia Sedona EX
2008 HVAC Blower & A/C Controls (Automatic) - Sedona
Microsoft
Monday, May 24, 2010 3:56:07 PM
Page 35
© 2006 Mitchell Repair Information Company, LLC.
Fig. 41: Checking Voltage Between Terminals And Of Driver Direction Potentiometer
Courtesy of KIA MOTORS AMERICA, INC.
DOOR POSITION CHART
Fig. 42: Output Voltage Graph
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured voltage within specifications in DOOR POSITION CHART?
YES
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage.
Door position
Voltage (6-7)
Error detecting
VENT
0.3 ± 0.15V
Under voltage: 0.08V or
less
Over voltage: 4.92V or
more
BI-LEVEL (1)
1.35 ± 0.4V
BI-LEVEL (2)
2.25 ± 0.4V
FLOOR
3.0 ± 0.4V
MIX
3.6 ± 0.4V
DEF
4.7 ± 0.15V
2008 Kia Sedona EX
2008 HVAC Blower & A/C Controls (Automatic) - Sedona
Microsoft
Monday, May 24, 2010 3:56:07 PM
Page 36
© 2006 Mitchell Repair Information Company, LLC.
Repair or replace as necessary and then go to "VERIFICATION OF VEHICLE REPAIR"
procedure.
NO
Substitute with a known-good actuator and check for proper operation. If the problem is corrected,
replace actuator and then go to "VERIFICATION OF VEHICLE REPAIR" procedure.
VERIFICATION OF VEHICLE REPAIR
After a repair, it is essential to verify that the fault has been corrected.
1. Connect scan tool and select "Diagnostic Trouble Codes (DTCs)" mode and then clear DTC.
2. Operate the vehicle and monitor the DTC on the scan tool.
3. Are any DTCs present?
YES
Go to the applicable troubleshooting procedure.
NO
System is performing to specification at this time.
DTC B1207 DIRECTION POTENTIOMETER SHORT (HIGH) - PASSENGER
COMPONENT LOCATION
Fig. 43: Identifying Temp Control Actuator (Passenger) Component Location
Courtesy of KIA MOTORS AMERICA, INC.
GENERAL DESCRIPTION
Refer to DTC B1206.
2008 Kia Sedona EX
2008 HVAC Blower & A/C Controls (Automatic) - Sedona
Microsoft
Monday, May 24, 2010 3:56:07 PM
Page 37
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст