Kia Sedona (2008 year). Instruction — part 26
VERIFICATION OF VEHICLE REPAIR
Refer to DTC C1101.
DTC C1625 CAN TIME-OUT ABS/TCS/ESC
COMPONENT LOCATION
Refer to DTC C1235.
GENERAL DESCRIPTION
Refer to DTC C1605.
DTC DESCRIPTION
The HECU checks the CAN communication lines for normal ESC control, and sets this code if a CAN message
is not transmitted within predefined time.
DTC DETECTING CONDITION
DTC DETECTING CONDITION CHART
COMPONENT INSPECTION
1. Ignition "OFF".
2. Engine "ON".
3. Does warning lamp remain On?
YES
Substitute with a known-good HECU and check for proper operation. If problem is corrected,
Item
Detecting Condition
Possible cause
DTC strategy
CAN massage monitoring
Inoperative HECU
Monitoring Period
Continuous
Enable Conditions
Faults are detected if CAN
message was not transmitted
on time by the CAN
controller of HECU.
Fail Safe
Inhibit the ESC control and
ABS/EBD control is
available. Meanwhile, stop
checking the ESC switch
failure under the ESC
control.
2008 Kia Sedona
2008 BRAKES ABS (Anti-Lock Brake System) - Sedona
Microsoft
Saturday, May 22, 2010 6:52:43 PM
Page 101
© 2006 Mitchell Repair Information Company, LLC.
replace HECU and then go to "VERIFICATION OF VEHICLE REPAIR" procedure.
NO
Fault is intermittent caused by inoperative HECU or was repaired and HECU memory was not
cleared. Go to the applicable troubleshooting procedure.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC C1101.
DTC C1626 IMPLAUSIBLE CONTROL
COMPONENT LOCATION
Refer to DTC C1235.
GENERAL DESCRIPTION
The HECU send requirement data, such as Torque reduction, the number of fuel cut cylinders, and TCS control
requests, to the PCM (ECM & TCM) through CAN bus line. The PCM (ECM) performs fuel cut functions
according to requests from the HECU and retards ignition timing by torque reduction requests. The PCM
(TCM) maintains current gear positions during TCS control time, in order not to increase power which causes a
Kickdown shift.
DTC DESCRIPTION
Under normal conditions, the inlet valves of all four wheels are not closed during control for longer than 1.28s
or If the controller requests pressure-hold or pressure-decrease for longer than 1.28s, a fault is detected. The
ABS/ESC warning lamp is turned ON and the EBD warning lamp is turned OFF.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
Item
Detecting Condition
Possible cause
DTC strategy
Signal monitoring
Case 1
Monitoring Period
Continuous
Enable Conditions
If the controller
requests pressure-
hold or pressure-
decrease for longer
than 1.28 s, a fault is
stored.
Monitoring Period
Continuous (at
vehicle reference
speed > 6 m/s, no
2008 Kia Sedona
2008 BRAKES ABS (Anti-Lock Brake System) - Sedona
Microsoft
Saturday, May 22, 2010 6:52:43 PM
Page 102
© 2006 Mitchell Repair Information Company, LLC.
COMPONENT INSPECTION
Refer to DTC C1101.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC C1101.
DTC C1702 VARIANT CODING ERROR
COMPONENT LOCATION
Refer to DTC C1235.
GENERAL DESCRIPTION
The HECU is programmed with a variant code based on the vehicle powertrain configuration. This variant code
is used to determine the appropriate ESC calculations.
DTC DESCRIPTION
The HECU checks the variant code after ignition. If a inappropriate variant code is detected or there is no
variant code, a fault is detected.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
Case 2
detected under
voltage and a fault is
not already detected)
Inoperative HECU
Enable Conditions
The monitoring
reports a failure if
continuous ESC
control occurs for a
time period > = 10 s.
Fail Safe
The ABS/ESC
functions are
inhibited, allow the
EBD control.
The ABS/ESC
warning lamps are
activated.
Item
Detecting Condition
Possible cause
DTC strategy
Internal monitoring
2008 Kia Sedona
2008 BRAKES ABS (Anti-Lock Brake System) - Sedona
Microsoft
Saturday, May 22, 2010 6:52:43 PM
Page 103
© 2006 Mitchell Repair Information Company, LLC.
MONITOR SCAN TOOL DATA
VARIANT CODE
1. Check for improper installation of PCM (ECM & TCM)/ESC.
2. Connect scan tool to Data Link Connector (DLC).
3. Ignition "ON".
4. Go in Anti-Lock brake system (figure 1).
5. Perform variant code.
6. Disconnect scan tool.
7. Ignition "OFF" and then ignition "ON". Go to "COMPONENT INSPECTION" Procedure.
Fig. 64: Scan Tool Display - Current Data
Courtesy of KIA MOTORS AMERICA, INC.
Monitoring Period
Once during startup.
Inoperative HECU
Replacement of PCM
(ECM & TCM)
Enable Conditions
During initialization, there is
no inputed valid variant code.
No variant code stored in
EEPROM.
Received variant code is
invalid.
There is a difference between
preset variant code and
detected variant code.
Fail Safe
The ABS/EBD/ESC functions
are inhibited.
The ABS/EBD/ESC warning
lamps are activated.
2008 Kia Sedona
2008 BRAKES ABS (Anti-Lock Brake System) - Sedona
Microsoft
Saturday, May 22, 2010 6:52:43 PM
Page 104
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст