Kia Sedona (2008 year). Instruction — part 204
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Check if DTC is erased after replacing FAM with "FAM for test".
4. Is the DTC erased?
YES
Replace "FAM for test" with "new FAM" and go to "VERIFICATION OF VEHICLE
REPAIR".
NO
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage. Repair or replace if necessary and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B2119.
DTC B2553 RIGHT HEADLAMP LOW CIRCUIT OPEN ERROR
COMPONENT LOCATION
Refer to DTC B2535.
GENERAL DESCRIPTION
Refer to DTC B2535.
DTC DESCRIPTION
The ECM sets DTC B2553 if open in Right headlamp low circuit is detected.
DTC DETECTING CONDITION
Refer to DTC B2541.
MONITOR DTC STATUS
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF" & FAM: "ON".
3. Select "Diagnostic Trouble Codes (DTCs)"mode and monitor "DTC Status" parameter.
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:21 PM
Page 285
© 2006 Mitchell Repair Information Company, LLC.
Fig. 242: Identifying Scan Tool Display - Diagnostic Trouble Codes (DTCs)
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the DTC B2553 present?
YES
Go to TERMINAL AND CONNECTOR INSPECTION.
NO
Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and
ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending,
corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to
"VERIFICATION OF VEHICLE REPAIR" procedure.
TERMINAL AND CONNECTOR INSPECTION
Refer to DTC B2119.
POWER SUPPLY CIRCUIT INSPECTION
1. Check open in power circuit
1. Ignition "ON" & engine "OFF".
2. Measure the resistance between headlamp low power circuit of FAM (BCM-FE-60) and headlamp
(E22-1).
Specification: infinity ohms
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:21 PM
Page 286
© 2006 Mitchell Repair Information Company, LLC.
Fig. 243: Measuring Resistance Between Headlamp Low Power Circuit Of FAM (BCM-FE-
60) And Headlamp (E22-1)
Courtesy of KIA MOTORS AMERICA, INC.
3. Is the measured resistance within the specification?
YES
Go to "GROUND CIRCUIT INSPECTION".
NO
Repair open in power circuit and go to "VERIFICATION OF VEHICLE REPAIR".
GROUND CIRCUIT INSPECTION
1. Check open in ground circuit
1. Ignition "ON" & engine "OFF".
2. Measure the resistance between Left turn signal lamp ground circuit (E24-3) and chassis ground.
Specification: 0 ohms
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:21 PM
Page 287
© 2006 Mitchell Repair Information Company, LLC.
Fig. 244: Measuring Resistance Between Left Turn Signal Lamp Ground Circuit (E24-3) And
Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
3. Is the measured resistance within the specification?
YES
Go to "COMPONENT INSPECTION".
NO
Repair open in ground circuit and go to "VERIFICATION OF VEHICLE REPAIR".
COMPONENT INSPECTION
Refer to DTC B2551.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B2119.
DTC B2555 LEFT HEADLAMP LOW CIRCUIT SHORT TO GROUND ERROR
COMPONENT LOCATION
Refer to DTC B2539.
GENERAL DESCRIPTION
Refer to DTC B2535.
DTC DESCRIPTION
The ECM sets DTC B2555 if short to ground in Left headlamp low circuit is detected.
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:21 PM
Page 288
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст