Kia Sedona (2008 year). Instruction — part 264
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage. Repair or replace as necessary and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
NO
Substitute with a known-good actuator and check for proper operation. If the problem is corrected,
replace actuator and then go to "VERIFICATION OF VEHICLE REPAIR" procedure.
3. Check A/C Control Unit.
1. Engine: "ON"
2. Connect A/C Control Unit.
3. Measure voltage between terminal "15" and "16" of A/C Control Unit while operating the mode
switch.
Specification :Approx. 12V
Fig. 202: Checking Voltage Between Terminal "15" And "16" Of A/C Control Unit
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured voltage within specifications?
YES
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage. Repair or replace as necessary and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
NO
Substitute with a known-good A/C Control Unit and check for proper operation.
If the problem is corrected, replace A/C Control Unit and then go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
VERIFICATION OF VEHICLE REPAIR
After a repair, it is essential to verify that the fault has been corrected.
2008 Kia Sedona EX
2008 HVAC Blower & A/C Controls (Automatic) - Sedona
Microsoft
Monday, May 24, 2010 3:56:10 PM
Page 178
© 2006 Mitchell Repair Information Company, LLC.
1. Connect scan tool and select "Diagnostic Trouble Codes (DTCs)" mode and then clear DTC.
2. Operate the vehicle and monitor the DTC on the scan tool.
3. Are any DTCs present?
YES
Go to the applicable troubleshooting procedure.
NO
System is performing to specification at this time.
2008 Kia Sedona EX
2008 HVAC Blower & A/C Controls (Automatic) - Sedona
Microsoft
Monday, May 24, 2010 3:56:10 PM
Page 179
© 2006 Mitchell Repair Information Company, LLC.
2008 ACCESSORIES & BODY, CAB
Body (Interior & Exterior) - General - Sedona
SPECIFICATIONS
GENERAL SPECIFICATIONS
TIGHTENING TORQUE
TIGHTENING TORQUE SPECIFICATIONS
HOOD
Type
Rear hinged, gas lifter type
FRONT DOOR
Construction
Front hinged, full door
construction
Regulator system
X-ARM type
Locking system
Pin-fork system
REAR DOOR
Construction
Sliding door construction
Regulator system
Wire drum type
Locking system
Pin-fork system
TAILGATE
Type
Inner hinged, gas lifter type
GLASS THICKNESS
Windshield glass
5 mm
Front door glass
4 mm
Rear door glass
4 mm
Rear window glass
3.5 mm
SEAT BELTS
Front
3 point type with Emergency
Locking Retractor (ELR)
Rear
3 point type with Emergency
Locking Retractor (ELR)
Items
N.m
Kgf. m
Lbf. ft
Front and rear doors Door hinge to body
33.3-41.2
3.4-4.2
24.6-30.4
Door hinge to door
21.6-26.5
2.2-2.7
15.9-19.5
Striker
6.9-10.8
0.7-1.1
5.1-8.0
Glass mounting bolt
7.8-11.8
0.8-1.2
5.8-8.7
Outside handle
mounting bolt
6.9-10.8
0.7-1.1
5.1-8.0
Rear channel
mounting nut
7.8-11.8
0.8-1.2
5.8-8.7
Tailgate
Tailgate hinge to
body
6.9-8.8
0.7-0.9
5.1-6.5
Tailgate hinge to
tailgate
6.9-8.8
0.7-0.9
5.1-6.5
Tailgate lift
mounting bolt
6.9-8.8
0.7-0.9
5.1-6.5
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB Body (Interior & Exterior) - General - Sedona
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB Body (Interior & Exterior) - General - Sedona
Microsoft
Monday, May 24, 2010 4:05:08 PM
Page 1
© 2006 Mitchell Repair Information Company, LLC.
Microsoft
Monday, May 24, 2010 4:05:11 PM
Page 1
© 2006 Mitchell Repair Information Company, LLC.
SPECIAL TOOLS
SPECIAL TOOLS REFERENCE CHART
Key cylinder
mounting nut
6.9-10.8
0.7-1.1
5.1-8.0
Hood
Hood hinge to body
21.6-26.5
2.2-2.7
15.9-19.5
Hood hinge to hood
21.6-26.5
2.2-2.7
15.9-19.5
Hood latch to body
6.9-10.8
0.7-1.1
5.1-8.0
Seat
Front seat mounting
bolts
43.1-64.7
4.4-6.6
31.8-47.7
Rear seat mounting
bolts
43.1-64.7
4.4-6.6
31.8-47.7
Seat belt
Front seat belt
height adjuster
39.2-53.9
4.0-5.5
28.9-39.8
Front seat belt
buckle mounting
bolt
39.2-53.9
4.0-5.5
28.9-39.8
Front seat belt
anchor mounting
bolt
39.2-53.9
4.0-5.5
28.9-39.8
Front seat belt lower
anchor
39.2-53.9
4.0-5.5
28.9-39.8
Front seat belt upper
anchor
39.2-53.9
4.0-5.5
28.9-39.8
Rear seat belt
anchor attaching
bolt
39.2-53.9
4.0-5.5
28.9-39.8
Rear seat belt
retractor mounting
bolt
39.2-53.9
4.0-5.5
28.9-39.8
Tool (Number and name)
Illustration
Use
09793-2100
Door hinge adjusting wrench
Adjustment, removal and
installation
Of the door hinge
09800-21000
Ornament remover
Trim removal
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB Body (Interior & Exterior) - General - Sedona
Microsoft
Monday, May 24, 2010 4:05:08 PM
Page 2
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст