Kia Sedona (2008 year). Instruction — part 182
4. Is the measured resistance within specifications?
YES
Go to "POWER CIRCUIT INSPECTION" procedure.
NO
Check for short in signal harness. Repair as necessary and go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
POWER SUPPLY CIRCUIT INSPECTION
1. Motor Power circuit Inspection
1. Ignition "OFF"
2. Disconnect driver Door lock actuator.
3. Measure resistance between terminal "5" of DDM and chassis ground.
Specification: Approx. infinity ohms
Fig. 165: Measuring Resistance Between Terminal 5 Of DDM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured resistance within specifications?
YES
Go to "COMPONENT INSPECTION" procedure.
NO
Check for short in power harness. Repair as necessary and go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
COMPONENT INSPECTION
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:19 PM
Page 197
© 2006 Mitchell Repair Information Company, LLC.
1. Check driver Door lock actuator
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF"
3. Select `ACTUATION TEST' mode on scan tool and press [F1] to start
Fig. 166: Identifying Scan Tool Display - Actuation Test Of Driver Door Lock Actuator
Courtesy of KIA MOTORS AMERICA, INC.
4. Dose driver Door lock actuator work properly?
YES
Go to step 2.
NO
Substitute with a known-good left outside mirror and check for proper operation.
If the problem is corrected, replace left outside mirror and then go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
2. Check driver Door lock monitoring switch
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Measure voltage value between terminal "9" of DDM and chassis ground. While operating driver
door lock actuator.
Specification: Door lock --> 5V, Door unlock --> 0V
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:19 PM
Page 198
© 2006 Mitchell Repair Information Company, LLC.
Fig. 167: Measuring Voltage Value Between Terminal 9 Of DDM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured voltage within specifications?
YES
Go to step 3.
NO
Substitute with a known-good driver Door lock actuator and check for proper operation. If the
problem is corrected, replace driver Door lock actuator and then go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
3. Check DDM
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF"
3. Measure voltage value between terminal "5" of DDM and chassis ground. While operating driver
door lock switch.
Specification: 9-16V
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:19 PM
Page 199
© 2006 Mitchell Repair Information Company, LLC.
Fig. 168: Measuring Voltage Value Between Terminal 5 Of DDM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured voltage within specifications?
YES
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage.
Repair or replace as necessary and then go to "VERIFICATION OF VEHICLE REPAIR"
procedure.
NO
Substitute with a known-good DDM and check for proper operation.
If the problem is corrected, replace DDM and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B1910.
DTC B2331 DRIVE DOOR UNLOCK ACTUATOR ERROR
COMPONENT LOCATION
Refer to DTC B1910.
GENERAL DESCRIPTION
DDM is a node of CAN communication system which consists of IPM. FAM, RAM, ADM, IMS. Main
function of DDM is lock/unlock of door and window, adjusting position and fold/unfold of outside mirror. Door
lock actuator consists of motor and monitoring switch. According to Switch signal of DDM, Door lock actuator
operates motor to lock/unlock door and monitoring switch delivers result to DDM by voltage value.
DTC DESCRIPTION
The ECM sets DTC B2331 if there's short circuit in driver door unlock actuator circuit harness.
DTC DETECTING CONDITION
Refer to DTC B2330.
MONITOR DTC STATUS
1. Connect scan tool to Data Link Connector (DLC).
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:19 PM
Page 200
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст