Kia Sedona (2008 year). Instruction — part 168
REPAIR" procedure.
2. Check right outside mirror sensor
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF"
3. Measure voltage value between terminal "13" of outside mirror and chassis ground. While
operating outside mirror switch.
Specification: bottom end --> approx. 0.88V, upper end --> approx. 3.86V
Fig. 111: Measuring Voltage Value Between Terminal 13 Of Outside Mirror And Chassis
Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured voltage within specifications?
YES
Go to step 3.
NO
Substitute with a known-good right outside mirror and check for proper operation. If the problem is
corrected, replace right outside mirror and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
3. Check ADM
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF"
3. Measure voltage value between terminal "10, 11" of outside mirror and chassis ground. While
operating outside mirror switch.
Specification: 9-16V
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:18 PM
Page 141
© 2006 Mitchell Repair Information Company, LLC.
Fig. 112: Measuring Resistance Between Terminal 11 Of ADM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured voltage within specifications?
YES
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage. Repair or replace as necessary and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
NO
Substitute with a known-good ADM and check for proper operation.
If the problem is corrected, replace ADM and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B1912.
DTC B1952 OSRVM DEFOGGER ERROR
COMPONENT LOCATION
Refer to DTC B1910.
GENERAL DESCRIPTION
DDM is a node of CAN communication system which consists of IPM. FAM, RAM, ADM, IMS. Main
function of DDM is lock/unlock of door and window, adjusting position and fold/unfold of outside mirror.
DDM controls position, fold/unfold and defogging of outside mirror. Mirror defogger is located in outside
mirror assembly and wipes fog on the mirror according to signal of DDM which receives driver's signal.
DTC DESCRIPTION
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:18 PM
Page 142
© 2006 Mitchell Repair Information Company, LLC.
The ECM sets DTC B1952 if there's short circuit in OSRVM defogger circuit harness.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
MONITOR DTC STATUS
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Select "Diagnostic Trouble Codes (DTCs)"mode and monitor "DTC Status" parameter.
4. Is the DTC B1952 present?
YES
Go to TERMINAL AND CONNECTOR INSPECTION procedure.
NO
Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and
ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending,
corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to
"VERIFICATION OF VEHICLE REPAIR" procedure.
TERMINAL AND CONNECTOR INSPECTION
1. Many malfunctions in the electrical system are caused by poor harness and terminals.
Faults can also be caused by interference from other electrical systems, and mechanical or chemical
damage.
2. Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination,
deterioration, or damage.
3. Has a problem been found?
YES
Repair as necessary and go to "VERIFICATION OF VEHICLE REPAIR" procedure.
Item
Detecting Condition
Possible Cause
DTC Strategy
Check Resistance
short in signal harness
short in power harness
Faulty mirror defogger
Faulty DDM
Enable Conditions
IGN `ON' & Engine `OFF'
Threshold value
infinity ohms
Detecting time
50 ms
FAIL SAFE
-
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:18 PM
Page 143
© 2006 Mitchell Repair Information Company, LLC.
NO
Go to POWER SUPPLY CIRCUIT INSPECTION procedure.
POWER SUPPLY CIRCUIT INSPECTION
1. Check for short in power harness
1. Ignition "OFF"
2. Disconnect outside mirror defogger.
3. Measure resistance between terminal "3" of DDM and chassis ground.
Specification :Approx. infinity ohms
Fig. 113: Measuring Resistance Between Terminal 3 Of DDM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured resistance within specifications?
YES
Go to "COMPONENT INSPECTION" procedure.
NO
Check for short in power harness. Repair as necessary and go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
COMPONENT INSPECTION
1. Check outside mirror defogger
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF"
3. Select `ACTUATION TEST' mode on scan tool and press [F1] to start
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:18 PM
Page 144
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст