Kia Sedona (2008 year). Instruction — part 167
COMPONENT LOCATION
Refer to DTC B1912.
GENERAL DESCRIPTION
Refer to DTC B1912.
DTC DESCRIPTION
The ECM sets DTC B1913 if signal voltage of right outside mirror vertical sensor is out of range.
DTC DETECTING CONDITION
DTC DETECTING CONDITION
MONITOR DTC STATUS
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Select "Diagnostic Trouble Codes (DTCs)"mode and monitor "DTC Status" parameter.
4. Is the DTC B1913 present?
YES
Go to TERMINAL AND CONNECTOR INSPECTION procedure.
NO
Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and
ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending,
corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to
"VERIFICATION OF VEHICLE REPAIR" procedure.
TERMINAL AND CONNECTOR INSPECTION
Refer to DTC B1912.
SIGNAL CIRCUIT INSPECTION
Item
Detecting Condition
Possible Cause
DTC Strategy
Check Voltage
short in signal harness
short in power harness
Faulty outside mirror motor
Faulty outside mirror sensor
Faulty ADM
Enable Conditions
IGN `ON' & Engine `OFF'
Threshold value
0.88V < Output voltage < 3.86V
Detecting time
50 ms
FAIL SAFE
-
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:18 PM
Page 137
© 2006 Mitchell Repair Information Company, LLC.
1. Check for open in harness
1. Ignition "OFF".
2. Disconnect right outside mirror.
3. Measure resistance between terminal "13" of ADM and chassis ground.
Specification :Approx. infinity ohms
Fig. 107: Measuring Resistance Between Terminal 13 Of ADM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured resistance within specifications?
YES
Go to "POWER CIRCUIT INSPECTION" procedure.
NO
Check for short in signal harness. Repair as necessary and go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
POWER SUPPLY CIRCUIT INSPECTION
1. Motor Power circuit Inspection
1. Ignition "OFF"
2. Disconnect right outside mirror.
3. Measure resistance between terminal "10" of ADM and chassis ground.
4. Measure resistance between terminal "11" of ADM and chassis ground.
Specification :Approx. infinity ohms
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:18 PM
Page 138
© 2006 Mitchell Repair Information Company, LLC.
Fig. 108: Measuring Resistance Between Terminal 11 Of ADM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
5. Is the measured resistance within specifications?
YES
Go to step 2.
NO
Check for short in signal harness. Repair as necessary and go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
2. Sensor power circuit inspection
1. Ignition "ON" & Engine "OFF"
2. Disconnect right outside mirror.
3. Measure voltage between terminal "16" of ADM and chassis ground.
Specification: Approx. 5V
Fig. 109: Measuring Voltage Between Terminal 16 Of ADM And Chassis Ground
Courtesy of KIA MOTORS AMERICA, INC.
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:18 PM
Page 139
© 2006 Mitchell Repair Information Company, LLC.
4. Is the measured voltage within specifications?
YES
Go to "COMPONENT INSPECTION" procedure.
NO
Check for open or short in harness. Repair as necessary and go to "VERIFICATION OF
VEHICLE REPAIR" procedure.
COMPONENT INSPECTION
1. Check right outside mirror motor
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF"
3. Select `ACTUATION TEST' mode on scan tool and press [F1] to start
Fig. 110: Identifying Scan Tool Display - Actuation Test Of Right Outside Motor
Courtesy of KIA MOTORS AMERICA, INC.
4. Dose right outside mirror motor work properly?
YES
Go to step 2.
NO
Substitute with a known-good right outside mirror and check for proper operation. If the problem is
corrected, replace right outside mirror and then go to "VERIFICATION OF VEHICLE
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:18 PM
Page 140
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст