Kia Sedona (2008 year). Instruction — part 212
NO
Repair short to ground in power circuit and go to "VERIFICATION OF VEHICLE REPAIR".
COMPONENT INSPECTION
1. Check parking lamp
1. Ignition "ON" & engine "OFF".
2. Disconnect parking lamp light bulb.
3. Measure the resistance between both terminals of parking lamp light bulb.
Specification: approx. 0.04 ohms
(If light bulb fails, infinity ohms is measured.)
Fig. 272: Measuring Resistance Between Both Terminals Of Stop Lamp Light Bulb
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the measured resistance within the specification?
YES
Go to step 2.
NO
Replacing the light bulb with `light bulb for test', if normal operating condition is confirmed,
Replace `light bulb for test' with `new light bulb' and go to "VERIFICATION OF VEHICLE
REPAIR".
2. Check FAM
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF".
3. Check if DTC is erased after replacing FAM with "FAM for test".
4. Is the DTC erased?
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:21 PM
Page 317
© 2006 Mitchell Repair Information Company, LLC.
YES
Replace "FAM for test" with "new FAM" and go to "VERIFICATION OF VEHICLE
REPAIR".
NO
Check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration,
or damage. Repair or replace if necessary and then go to "VERIFICATION OF VEHICLE
REPAIR" procedure.
VERIFICATION OF VEHICLE REPAIR
Refer to DTC B2119.
DTC B2577 LEFT PARKING LAMP CIRCUIT OPEN ERROR
COMPONENT LOCATION
Fig. 273: Identifying Headlamp, Fog Lamp & Turn Signal Connectors
Courtesy of KIA MOTORS AMERICA, INC.
GENERAL DESCRIPTION
Refer to DTC B2535.
DTC DESCRIPTION
The ECM sets DTC B2577 if open in Left parking lamp circuit is detected.
DTC DETECTING CONDITION
Refer to DTC B2545.
MONITOR DTC STATUS
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:21 PM
Page 318
© 2006 Mitchell Repair Information Company, LLC.
1. Connect scan tool to Data Link Connector (DLC).
2. Ignition "ON" & engine "OFF" & FAM: "ON".
3. Select "Diagnostic Trouble Codes (DTCs)" mode and monitor "DTC Status" parameter.
Fig. 274: Identifying Scan Tool Display - Diagnostic Trouble Codes (DTCs)
Courtesy of KIA MOTORS AMERICA, INC.
4. Is the DTC B2577 present?
YES
Go to TERMINAL AND CONNECTOR INSPECTION.
NO
Fault is intermittent caused by poor contact in the sensor's and/or ECM's connector or was repaired and
ECM memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending,
corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to
"VERIFICATION OF VEHICLE REPAIR" procedure.
TERMINAL AND CONNECTOR INSPECTION
Refer to DTC B2119.
POWER SUPPLY CIRCUIT INSPECTION
1. Check open in power circuit
1. Ignition "ON" & engine "OFF".
2. Measure the resistance between parking lamp power circuit of FAM (BCM-FE-40)and parking
lamp (E24-2).
Specification: 0 ohms
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:21 PM
Page 319
© 2006 Mitchell Repair Information Company, LLC.
Fig. 275: Measuring Resistance Between Parking Lamp Power Circuit Of FAM (BCM-FE-
40)And Parking Lamp (E24-2)
Courtesy of KIA MOTORS AMERICA, INC.
3. Is the measured resistance within the specification?
YES
Go to "GROUND CIRCUIT INSPECTION".
NO
Repair open in power circuit and go to "VERIFICATION OF VEHICLE REPAIR".
GROUND CIRCUIT INSPECTION
1. Check open in ground circuit
1. Ignition "ON" & engine "OFF".
2. Measure the resistance between parking lamp ground circuit (E24-3) and chassis ground.
Specification: 0 ohms
2008 Kia Sedona EX
2008 ACCESSORIES & BODY, CAB BCM (Body Control Module) - Sedona
Microsoft
Monday, May 24, 2010 4:19:21 PM
Page 320
© 2006 Mitchell Repair Information Company, LLC.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст