Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 128
4C–12
DRIVE SHAFT SYSTEM
Preload Adjustment
1. Tighten the hub nut to 29 N·m (22 lb ft), then fully
loosen the nut.
2. Tighten the hub nut to the value given below,
using a spring scale on the wheel pin.
New bearing and New
oil seal
19.6 – 24.5 N
(4.4 – 5.5 lb)
Used bearing and New
oil seal
11.8 – 17.7 N
(2.6 – 4.0 lb)
If the measured bearing preload is outside the
specifications, adjust it by loosening or tightening the
hub nut.
411RS011
9. Install lock washer and lock screw.
D
Turn the side with larger diameter of the tapered
bore to the vehicle outer side, then attach the
washer.
D
If the bolt holes in the lock plate are not aligned with
the corresponding holes in the nut, reverse the lock
plate.
D
If the bolt holes are still out of alignment, turn in the
nut just enough to obtain alignment.
D
Screw is to be fastened tightly so its head may
come lower than the surface of the washer.
411RS012
10. Apply adhesive (LOCTITE 515 or equivalent) to both
joining flange faces then install hub flange.
11. Install snap ring and shim.
D
Adjust the clearance between the free wheeling hub
body and the snap ring.
Clearance: 0 mm–0.3 mm (0 in–0.012 in)
Shims Available: 0.2 mm, 0.3 mm, 0.5 mm,
1.0 mm (0.008 in, 0.012 in, 0.020 in, 0.039 in)
411RW002
12. Install hub cap.
13. Tighten the bolts to the specified torque.
Torque: 59 N·m (43 lb ft)
14. Install brake caliper and tighten fixing bolt.
4C–13
DRIVE SHAFT SYSTEM
Front Drive Shaft Joint
Front Drive Shaft Joints
Replacement
D
Refer to
Front Drive Axle Assembly Replacement in
this section, and refer to
Front Hub and Disc Overhaul
in Suspension section.
Front Hub Bearing Preload Check
Check the hub bearing preload at the wheel pin.
New bearing and New oil seal:
19.6 – 24.5 N (4.4 – 5.5 lb)
Used bearing and New oil seal:
11.8 – 17.7 N(2.6 – 4.0 lb)
411RS011
Inspection Of Shift On The Fly System
Gear Oil
412RY00008
1. Open filler plug and make sure that the oil up to the
plug port.
If the oil is short, replenish with gear oil GL–5 grade.
2. Tighten the filler plug to specified torque.
Torque: 78 N·m (58 lb in)
4C–14
DRIVE SHAFT SYSTEM
Front Axle Drive Shaft
Front Axle Drive Shaft and Associated Parts
412RY00036
Legend
(1) Axle Case and Differential
(2) Snap Ring
(3) Bearing
(4) Snap Ring
(5) Oil Seal
(6) Bracket
(7) DOJ Case
(8) Circlip
(9) Bolt
(10) Drive Shaft Joint Assembly
(11) Ball
(12) Snap Ring
(13) Ball Retainer
(14) Ball Guide
(15) Band
(16) Bellows
(17) Band
(18) Band
(19) Bellows
(20) Band
(21) BJ Shaft
(22) Dust Seal
4C–15
DRIVE SHAFT SYSTEM
Disassembly
NOTE: For the left side, follow the same steps as right
side.
1. Raise the hooked end of the band with a screwdriver
or equivalent.
412RS009
2. Remove band(1).
3. Pry off circlip (1) with a screwdriver or equivalent.
412RS010
4. Remove drive shaft joint assembly.
5. Remove the six balls (1) with a screwdriver or
equivalent.
412RS012
6. Using snap ring pliers, remove the snap ring (1)
fastening the ball retainer to the center shaft.
412RS013
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст