Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 48
2A–38 POWER–ASSISTED STEERING SYSTEM
CAUTION: Never apply force to the steering wheel
shaft using a hammer or other impact tools in an
attempt to remove the steering wheel. The steering
shaft is designed as an energy absorbing unit.
430RX005
9. Remove steering column cover.
10. Disconnect the wiring harness connectors located
under the steering column then remove combination
switch and SRS coil assembly.
825RW288
Installation
1. Install combination switch and SRS coil assembly.
After installation of combination switch assembly,
connect the combination switch wiring harness
connector and the SRS 2-way connector located
under the steering column. Then turn the SRS coil
counter clockwise to full, return about 3 turns and
align the neutral mark.
CAUTION: Turn the SRS coil counter clockwise
until some resistance is felt, or damage may occur to
the SRS coil.
825RW016
POWER–ASSISTED STEERING SYSTEM
2A–39
2. When installing the steering column cover, be sure to
route each wire harness as illustrated so that the
harnesses do not catch on any moving parts.
825RW017
Legend
(1) Steering Column Cover
(2) Starter Switch Harness
(3) Combination Switch Harness
(4) Inflator Module Harness
3. Align the setting marks made when removing then
install steering wheel.
CAUTION: Never apply force to the steering wheel
shaft using a hammer or other impact tools in an
attempt to remove the steering wheel. The steering
shaft is designed as an energy absorbing unit.
4. Tighten the steering wheel fixing nut to the specified
torque.
Torque: 34 N·m (25 lb ft)
5. Support the inflator module and carefully connect the
SRS connector and horn lead.
NOTE: Pass the lead wire through the tabs on the plastic
cover (wire protector) of inflator to prevent lead wire from
being pinched.
6. Tighten bolts to specified torque.
Torque: 9 N·m (78 lb in)
7. Install driver knee bolster (reinforcement).
8. Install instrument panel lower cover then Install the
engine hood opening lever.
9. Connect the SRS connector.
10. Connect the battery “-” terminal cable.
11. Turn the ignition switch to the “ON” position and
observe the warning lamp. The lamp should flash 7
times. If the lamp does not operate correctly, refer to
Restraints section.
2A–40 POWER–ASSISTED STEERING SYSTEM
Lock Cylinder
Lock Cylinder and Associated Parts
431RX005
Legend
(1) Inflator Module
(2) Steering Wheel
(3) Steering Column Cover
(4) Combination Switch and SRS Coil Assembly
(5) Snap Ring
(6) Cushion Rubber
(7) Lock Cylinder Assembly
(8) Instrument Panel Lower Cover
(9) Driver Knee Bolster (reinforcement)
(10) Shift Lock Cable (for A/T)
Removal
1. Turn the steering wheel so that the vehicle’s wheels
are pointing straight ahead.
2. Turn the ignition switch to “LOCK”.
3. Disconnect the battery ground cable, and wait at least
5 minutes.
4. Disconnect the yellow 2-way SRS connector located
under the steering column.
CAUTION: The wheels of the vehicle must be
straight ahead and the steering column in the
”LOCK” position before disconnecting the steering
wheel. Failure to do so will cause the coil assembly
to become uncentered which will cause damage to
the coil assembly.
5. Remove the engine hood opening lever and steering
lower cover.
6. Remove driver knee bolster (reinforcement).
POWER–ASSISTED STEERING SYSTEM
2A–41
7. Loosen the inflator module fixing bolt from behind the
steering wheel assembly using a TORX
driver or
equivalent until the inflator module can be released
from steering assembly.
827RW070
8. Disconnect the yellow 2-way SRS connector and
horn lead located behind the inflator module.
827RW073
9. Apply a setting mark (1) across the steering wheel
and shaft so parts can be reassembled in their original
position.
430RW021
10. Move the front wheels to the straight ahead position,
then use steering wheel remover J–29752 to remove
the steering wheel.
CAUTION: Never apply force to the steering wheel
shaft using a hammer or other impact tools in an
attempt to remove the steering wheel. The steering
shaft is designed as an energy absorbing unit.
430RX005
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст