Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 1734
REAR SUSPENSION
3D–13
• Install the rubber bushing (Frame side) by using
Installer J–39215.
NOTE: When mounting rubber bushings, do not use
grease on bushings or any other nearby parts.
901RW061
3. Rubber bushing (Axle side)
• Remove the rubber bushing (Axle side) by using
remover J–39792.
901RW062
• Install the rubber bushing (Axle side) by using
installer J–39792.
901RW063
Installation
1. Install lateral rod and make sure that the lateral rod
is in its correct position.
NOTE: When mounting lateral rod, be sure not to use
grease on bushings or any other nearby part.
460RW008
EndOFCallout
2. Install bolt and nut (Frame side). Tighten the bolt
and nut lightly, then retighten them to the specified
torque after the vehicle is at curb height.
Torque: 137 N·m (101 lb ft)
3. Install nut and washer (Axle side). Tighten the nut
lightly, then retighten the nut to the specified torque
after the vehicle is at curb height.
Torque: 78 N·m (58 lb ft)
Legend
(1) Frame Side
(2) Axle Side
3D–14
REAR SUSPENSION
Stabilizer Bar
Stabilizer Bar and Associated Parts
460R200003
EndOFCallout
Removal
1. Raise the vehicle and support the frame with
suitable safety stands.
2. Remove wheel and tire assembly. Refer to Wheel in
this section.
3. Remove bolt and nut.
4. Remove link.
5. Remove bracket.
6. Remove rubber bushing.
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are
found through inspection.
Check the following parts:
• Stabilizer bar
• Rubber bushing
• Link
Legend
(1) Bracket and Blot
(2) Link
(3) Bolt and Nut
(4) Stabilizer Bar
(5) Rubber Bushing
REAR SUSPENSION
3D–15
Installation
1. Install rubber bushing.
2. Install bracket to axle housing and tighten to the
specified torque.
Torque: 25 N·m (18 lb ft)
3. Install link.
4. Install bolt and nut, then tighten the nut to the
specified torque.
Torque: 50 N·m (37 lb ft)
460R200002
Main Data and Specifications
General Specifications
Rear suspension
Type
5–Link, coil spring type with stabilizer bar.
Coil spring
Free length
Soft Top
Resin Top
374.5mm (14.74in)
383.5mm (15.10in)
Spring diameter
12.3mm (0.48in)
12.5mm (0.49in)
Coil diameter (inner)
105mm (4.13in)
Effective No. of turns
6.23
6.59
Total No. of turns
7.73
8.09
Shock absorber
Type
Hydraulic, double acting, telescopic
Piston diameter
30mm (1.18in)
Stroke
Without ISC
shock
absorber
175.0 mm
(6.89 in)
With ISC
shock
absorber
159 mm
(6.26in)
Extended length
473.5 mm
(18.64in)
518 mm
(20.39 in)
Compressed length
298.5 mm
(11.75 in)
359 mm
(14.13 in)
Stabilizer bar
Diameter
19mm (0.71in)
3D–16
REAR SUSPENSION
Torque Specifications
E03R200006
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст