Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 1683
SEAT BELT SYSTEM
9A–9
Inspection of retractor
1. ELR (Emergency Locking Retractor) lock inclining
angle check.
• The seat belt should not lock when pulled gently
at a 15 degree angle. Also, the seat belt should
lock when pulled at a 45 degree angle or higher.
2. ELR lock check.
• The seat belt should not lock when pulled slowly,
however, the seat belt should lock when pulled
quickly.
3. ALR (Automatic Locking Retractor)/ELR check
(Except for driver's seat).
• Make sure the seat belt is locked when pulled out
fully.
• Make sure the seat belt can be pulled out and
retracts after when rewound fully.
CAUTION: Do not disassemble the retractor.
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1. Tighten the adjustable shoulder anchor assembly
fixing bolts to the specified torque.
Torque: 39 N·m (29 lb ft)
2. Tighten the seat belt anchor bolts (Upper & Lower)
and the retractor fixing bolts to the specified torque.
Torque: 39 N·m (29 lb ft)
9A–10
SEAT BELT SYSTEM
Rear Seat Belt (SWB)
Rear Seat Belt and Associated Parts
760R200023
EndOFCallout
Removal
1. Disconnect the battery ground cable.
2. Remove the luggage side lid (2).
3. Remove the luggage side front cover (4).
4. Remove the luggage side upper cover (3).
Legend
(1) Seat Belt Cross Bar Assembly
(2) Seat Belt Upper Anchor Bolt
(3) Shoulder Anchor Cover
(4) Rear Seat Belt Assembly
(5) Retractor
(6) Anchor Cover
(7) Seat Belt Lower Anchor Bolt
(8) Lower Quarter Trim Cover
SEAT BELT SYSTEM
9A–11
5. Remove the canopy cover (1) (Resin top model).
• Remove two fixing clips.
686RX001
• Remove the three bolts and three screws, and
then remove quarter side molding (Soft top
model).
687RW002
6. Remove the tailgate weather strip.
7. Remove the rear end floor trim cover.
8. Remove the luggage side trim cover (RH).
• Remove the jack & tool lid and remove the tool.
• Remove fixing screw and pry the trim cover
retainers free from the body panel.
687RW005
9. Remove the luggage side trim cover (LH).
• Remove fixing screw and pry the trim cover
retainers free from the body panel.
• Disconnect the accessory socket connectors.
10. Remove the anchor cover and seat belt lower
anchor bolt.
11. Remove the shoulder anchor cover (2).
• Release the hooked portion of cover from the
shoulder anchor (1).
755RW070
12. Remove the seat belt upper anchor bolt.
13. Remove the retractor.
14. Remove the rear seat belt assembly.
9A–12
SEAT BELT SYSTEM
Inspection
If any of the following abnormalities is found, replace on
an assembly basis.
• Uneven movement of upper/lower anchors (1) in the
circumferential direction.
• Damaged and/or deformed through ring (2).
• Damaged and/or deformed tongue (4).
• Damaged and/or frayed webbing (3).
• Deformed retractor bracket (5).
• Seat belt does not retract (6).
• Resistance or abnormal sound when seat belt is
pulled out or retracted (6).
• Retractor (6) abnormality.
755R100004
Inspection of retractor
1. ELR (Emergency Locking Retractor) lock inclining
angle check.
• The seat belt should not lock when pulled gently
at a 15 degree angle. Also, the seat belt should
lock when pulled at a 45 degree angle or higher.
2. ELR lock check.
• The seat belt should not lock when pulled slowly,
however, the seat belt should lock when pulled
quickly.
3. ALR (Automatic Locking Retractor)/ELR check
(Except for driver's seat).
• Make sure the seat belt is locked when pulled out
fully.
• Make sure the seat belt can be pulled out and
retracts after when rewound fully.
CAUTION: Do not disassemble the retractor.
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Align the projection of the retractor to the square
hole of the seat belt cross bar assembly bracket.
2. Tighten the retractor fixing bolts to the specified
torque.
Torque: 39 N·m (29 lb ft)
3. Tighten the seat belt anchor bolt to the specified
torque.
Torque: 39 N·m (29 lb ft)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст