Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 1682
SEAT BELT SYSTEM
9A–5
7. Remove the rear speaker (2).
• Remove the speaker grille (1) and remove the
speaker fixing screws.
• Disconnect the connector (3).
890RW048-1
8. Remove the lower quarter trim cover.
• Pry the trim cover retainers free from the body
panel.
9. Remove the dome light.
• Remove the dome light lens and the fixing
screws.
• Disconnect the dome light connector.
10. Remove the soft top latch (Soft top model).
• Remove two bolts.
665RW023
11. Remove the rear roof bracket (2) (Resin top model).
• Remove the rear roof bracket cover (4) and
remove rear roof bracket connecting with resin
top (1) and rear roof trim cover (3) by removing
four fixing bolts.
666RW006
12. Remove the rear roof trim cover.
13. Remove the assist grip.
14. Remove the door seal finisher.
15. Remove the upper quarter trim cover.
16. Remove the seat belt upper anchor bolt.
17. Remove the retractor fixing bolt.
18. Remove the seat belt assembly.
19. Remove the adjustable shoulder anchor assembly.
• Remove two bolts.
9A–6
SEAT BELT SYSTEM
Inspection
If any of the following abnormalities is found, replace on
an assembly basis.
• Deformed and malfunctioning adjustable shoulder
anchor (1).
• Uneven movement of upper/lower anchors (2) in the
circumferential direction.
• Damaged and/or deformed through ring (3).
• Damaged and/or deformed tongue (4).
• Damaged and/or frayed webbing (5).
• Deformed retractor bracket (6).
• Seat belt does not retract (7).
• Resistance or abnormal sound when seat belt is
pulled out or retracted (7).
• Retractor (7) abnormality.
760R100032
Inspection of retractor
1. ELR (Emergency Locking Retractor) lock inclining
angle check.
• The seat belt should not lock when pulled gently
at a 15 degree angle. Also, the seat belt should
lock when pulled at a 45 degree angle or higher.
2. ELR lock check.
• The seat belt should not lock when pulled slowly,
however, the seat belt should lock when pulled
quickly.
3. ALR (Automatic Locking Retractor)/ELR check
(Except for driver's seat).
• Make sure the seat belt is locked when pulled out
fully.
• Make sure the seat belt can be pulled out and
retracts after when rewound fully.
CAUTION: Do not disassemble the retractor.
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
CAUTION: When replacing the front seat belt,
always replace the seat belt with the same parts/part
number.
1. Tighten the adjustable shoulder anchor assembly
and retractor fixing bolts to the specified torque.
Torque: 39 N·m (29 lb ft)
2. Tighten the seat belt anchor bolts to the specified
torque.
Torque: 39 N·m (29 lb ft)
SEAT BELT SYSTEM
9A–7
Rear Seat Belt (LWB)
Rear Seat Belt and Associated Parts
760R100049
EndOFCallout
Removal
1. Disconnect the battery ground cable.
2. Remove the tailgate weather strip.
3. Remove the rear end floor trim cover.
Legend
(1) Adjustable Shoulder Anchor Assembly
(2) Seat Belt Upper Anchor Bolt
(3) Slider Plate Trim Assembly
(4) Upper Quarter Trim Cover
(5) Rear Roof Trim Cover
(6) Tailgate Weather Strip
(7) Rear End Floor Trim Cover
(8) Lower Quarter Trim Cover
(9) Seat Belt Lower Anchor Bolt
(10) Anchor Cover
(11) Rear Seat Belt Assembly
(12) Screw
(13) Retractor
(14) Rear Sill Plate
(15) Rear Door Seal Finisher
9A–8
SEAT BELT SYSTEM
4. Remove the luggage room light.
• Remove the luggage room light lens (1) and the
fixing screw.
• Disconnect the luggage room light connector.
825RW100
5. Remove the rear roof trim cover.
• Pry the trim cover clips free from the body panel.
6. Remove the rear sill plate.
7. Remove the anchor cover and the lower anchor
bolt.
8. Remove the upper and lower quarter trim cover.
• Refer to Interior Trim Panel (LWB) in Exterior/
Interior Trim section.
9. Remove the slider plate trim assembly (2).
• Remove the two fixing screws from the adjustable
shoulder anchor (1).
• Pull out the seat belt through the hole (3) on the
slider plate trim.
755RW069
10. Remove the seat belt upper anchor bolt.
11. Remove the retractor.
12. Remove the rear seat belt assembly.
13. Remove the adjustable shoulder anchor assembly.
• Remove the two fixing bolts.
Inspection
If any of the following abnormalities is found, replace on
an assembly basis.
• Deformed and malfunctioning adjustable shoulder
anchor (1).
• Uneven movement of upper/lower anchors (2) in the
circumferential direction.
• Damaged and/or deformed through ring (3).
• Damaged and/or deformed tongue (4).
• Damaged and/or frayed webbing (5).
• Deformed retractor bracket (6).
• Seat belt does not retract (7).
• Resistance or abnormal sound when seat belt is
pulled out or retracted (7).
• Retractor (7) abnormality.
760R200022
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст