Isuzu Amigo / Axiom / Trooper / Rodeo / VehiCross. Service manual — part 1675
EXTERIOR/INTERIOR TRIM
8J–7
Removal
1. Disconnect the battery ground cable.
2. Remove the regulator handle(1).
• Pull the hook(2) out and remove the regulator
handle.
631RW002
3. Remove the one screw from the pullcase.
655R100002
4. Remove the inside handle fixing screw.
CAUTION: Do not apply excessive force on the
inside handle link or damage may occur, which
could make the inside handle difficult to operate.
5. Remove the rear door corner garnish.
• Pull the garnish to disconnect the retaining clip.
6. Remove the door trim panel.
• Pull out the eight clip positions from the door
panel.
655R100003
• Disconnect the power window switch connector
to lift the trim panel and unlock the engagement
of the waist seal section, then pass the inside
lever through the mounting hole of the trim panel,
and detach the trim panel.
7. Remove the inside handle.
8. Remove the power window switch and pull case.
• Remove the fixing screws from back side of the
rear door trim.
Installation
To install, follow the removal steps in the reverse order.
8J–8
EXTERIOR/INTERIOR TRIM
Door Mirror Assembly
Removal
1. Disconnect the battery ground cable.
2. Remove the door mirror cover (3).
3. Remove the door mirror assembly (1).
• Remove the three bolts and disconnect the
connector (2).
635RX011
Installation
To install, follow the removal steps in the reverse order.
EXTERIOR/INTERIOR TRIM
8J–9
Interior Trim Panels (LWB)
Interior Trim Panels and Associated Parts
643RY00001
EndOFCallout
Removal
1. Disconnect the battery ground cable.
2. Remove the sill plates (Front & Rear).
3. Remove the dash side trim cover.
4. Remove the lower center pillar trim cover.
• Remove the lower anchor bolt cover and lower
anchor bolt from the front seat belt.
• Pry the trim cover clips free from the body panel.
5. Remove the door finishers (Front & Rear).
6. Remove the upper center pillar trim cover.
• Pry the trim cover clips free from the body panel.
7. Remove the front pillar trim cover.
• Ply the trim cover clips free from the body panel.
8. Remove the tailgate weather strip.
9. Remove the rear end floor trim cover.
• Remove the five fixing screws.
Legend
(1) Assist Grip (Front & Rear)
(2) Door Finisher (Front & Rear)
(3) Upper Quarter Trim Cover
(4) Rear Roof Trim Cover
(5) Tailgate Weather Strip
(6) Rear End Floor Trim Cover
(7) Lower Quarter Trim Cover
(8) Sill Plate (Front & Rear)
(9) Lower Center Pillar Trim Cover
(10) Upper Center Pillar Trim Cover
(11) Front Pillar Trim Cover
8J–10
EXTERIOR/INTERIOR TRIM
10. Remove the luggage room light.
• Remove the luggage room light lens (1) and the
fixing screw.
• Disconnect the luggage room light connector.
825RW100
11. Remove the rear roof trim cover.
• Pry the trim cover clips free from the body panel.
12. Remove the tonneau cover assembly (1).
643RY00002
13. Remove the lower anchor bolt cover (6) and the
lower anchor bolt (5) from the rear seat belt.
14. Remove the lower quarter trim cover (1).
• Remove the tool box lid (3) and fixing screw (4).
Pry the five clip positions (2) free from the body
panel.
• Disconnect the accessory socket connector (LH
side).
643R100001
15. Remove the upper quarter trim cover (1).
• Pry the twelve clip positions (2) free from the
body panel.
643RY00004
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст