Isuzu N-Series. Service manual — part 244
ANTI-LOCK BRAKE SYSTEM (ABS) 5A4-41
3. How to erase code:
• Conduct brake switch ON/OFF operation 6 or more times within 3 seconds of self-diagnosis startup.
• The code cannot be erased if more than 3 seconds have passed since self-diagnosis startup, or if self-diag-
nosis has started with brake switched on (brake pedal depressed).
• DTCs can be erased also by Tech 2.
4. An example of DTC display
Display of DTC 23
After displaying DTC 12 three times, one DTC after another is displayed, starting with the most recent one. (However,
display is discontinued after about 5 minutes.)
The DTC 12 is displayed repeatedly. (display is discontinued after about 5 minutes)
N5A1035E
N5A1036E
5A4-42 ANTI-LOCK BRAKE SYSTEM (ABS)
5. How to display vehicle model:
1) Turn the key switch OFF.
2) Short the diagnosis connector terminal 12 to
ground.
3) Slightly push the brake pedal.
4) Turn the key switch ON.
5) ABS warning light illuminates.
6) Illuminating number of times indicates the vehi-
cle model.
N5A1037E
Vehicle model
Illuminating number of times
NKR, NPR FRONT
DISC BRAKE
1
NQR
8
NPR FRONT DRUM
BRAKE
5
0.4 sec.
0.4 sec.
NPR
FRONT DRUM BRAKE
1.2 sec.
NKR,NPR
FRONT DISC BRAKE
N5A1038E
ANTI-LOCK BRAKE SYSTEM (ABS) 5A4-43
Chart B-1-1 With the key in the ON position (Before starting the engine). Warning light (W/
L) is not activated.
Step
Action
Value(s)
YES
NO
1
Is W/L fuse F-16 blown out?
—
2
Is W/L bulb burnt out?
—
3
1. Turn the key off.
2. Disconnect EHCU connectors.
3. Turn the key on.
4. Using DVM, measure the voltage be-
tween J-177 EHCU connector terminals 6
and 1.
Does the DVM display a voltage within the
specified value?
12V:
9.5 — 16.5 V
24V:
16.5 — 34 V
4
Check the continuity between J-177 EHCU
connector terminal 1 and body ground.
Is there continuity?
—
5
Replace the fuse.
Is action complete?
—
—
6
Replace the W/L bulb.
Is action complete?
—
—
7
Locate and repair open circuit, poor connec-
tion or short circuit in the ignition feed circuit.
Is action complete?
—
—
8
Locate and repair open circuit, poor connec-
tion or short circuit in the ground circuit.
Is action complete?
—
—
9
1. Check the harness for suspected discon-
nection.
2. If no fault found, replace the EHCU.
Is action complete?
—
—
10
1. Reconnect all components, ensure all
components are properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
—
Go to “Basic diag-
nostic flow chart”.
—
5A4-44 ANTI-LOCK BRAKE SYSTEM (ABS)
Chart 1 (DTC13/C0213) Vehicle Type Error
Chart 2 (DTC14/C0214) EHCU Abnormality
Step
Action
Value(s)
YES
NO
1
1. Disconnect EHCU connector.
2. Turn the key on.
3. Measure the voltage at terminal 14, 15,
and 17.
NQR:
All terminal battery
voltage
NKR, NPR FRONT
DISC BRAKE:
All terminal 0 V
NPR FRONT DRUM
BRAKE:
Terminal 14, 15: 0 V
Terminal 17: battery
voltage
2
1. Turn the key off and connect EHCU.
2. Connect the Tech 2.
3. Clear the vehicle type.
4. Does the warning light turn off?
—
Replace the
EHCU.
3
Confirm the vehicle type.
Is the vehicle type okay?
—
Replace the
EHCU.
4
Clear the DTC.
—
Troubleshoot-
ing completed.
—
5
Repair harness.
Does the warning light turn off?
—
Replace the
EHCU.
Step
Action
Value(s)
YES
NO
1
1. Turn the key off.
2. Disconnect the EHCU connector.
3. Measure continuity between the body
ground and J-177 connector terminal 1,
23.
Is there continuity?
—
2
1. Connect the EHCU connector.
2. Clear DTC.
3. Turn the key from off to on and perform di-
agnosis procedure.
Does the DTC repeat?
—
3
Repair the open/short circuit or malfunction at
connection of connector.
Is this step completed?
—
—
4
Replace the EHCU.
Is this step completed?
—
—
5
1. Install all parts. Verify each part is proper-
ly installed.
2. Clear DTC.
Is this step completed?
—
Go to “Basic
diagnostic flow
chart”.
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст