Isuzu N-Series. Service manual — part 56
1A-18 HEATING AND VENTILATION
Removal
Preparation:
Disconnect the battery ground cable.
[Driver Side]
1. Meter CIuster
Refer to Section 2 “CAB AND FRAME” for Meter
Cluster removal procedure.
2. Ventilation Grille
Push the catches of the grille on the backside of
the cluster to the inside, and remove the ventilation
grille.
[Passenger Side]
1. Instrument Panel Assembly
Refer to Section 2 “CAB AND FRAME” for Instru-
ment Panel removal procedure.
2. Ventilation Duct
3. Ventilation Grille
Installation
To install, follow the removal steps in the reverse order.
N1A0035E
HEATING AND VENTILATION 1A-19
Defroster Nozzle/Ventilation Duct
Removal
Preparation:
Disconnect the battery ground cable.
1. Instrument Panel Assembly
Refer to Section 2 “CAB AND FRAME” for Instru-
ment Panel removal procedure.
2. Ventilation Duct (RH)
3. Ventilation Duct (CTR)
4. Ventilation Duct (LH)
5. Reinforcement Stay
6. Defroster Nozzle
7. Side Defroster Nozzle
Installation
To install, follow the removal steps in the reverse order.
Legend
1. Instrument panel assembly
6. Defroster nozzle (It is not installed on the vehicle with
forged air ventilation as an optional equipment.)
2. Ventilation duct (RH)
3. Ventilation duct (CTR)
7. Side defroster nozzle (It is not installed on the vehicle
with forged air ventilation as an optional equipment.)
4. Ventilation duct (LH)
5. Reinforcement stay
N1A0036E
1A-20 HEATING AND VENTILATION
Control Lever Assembly
Legend
1. Glove box
7. Control lever assembly
2. Center cluster
8. Fan switch connector
3. Knob
9. A/C switch connector
4. Control panel bezel
10. Illumination bulb connector
5. Control cable
11. Clip
6. A/C switch (A/C only)
N1A0037E
HEATING AND VENTILATION 1A-21
Removal
Preparation:
Disconnect the battery ground cable.
1. Glove Box
Open the glove box and remove the fixing screws.
2. Center Cluster
• While pulling the cluster with care, remove the
upper and the back side clips (1) of the cluster.
• Disconnect the cigar lighter and illumination
connectors.
3. Knob
4. Control Panel Bezel
Push the four catches at both sides of the bezel to
the inside, and remove the illumination bulb (1)
from the bezel (2).
5. Control Cable
Disconnect the control cables from the heater and
blower units.
6. A/C Switch
Push the catches at both sides of the A/C switch to
the inside, and remove the A/C switch by pulling it
out.
7. Control Lever Assembly
• Remove the lever fixing bolts and pull the lever
assembly out.
• Disconnect the A/C switch connector clip and
fan switch connector from the lever assembly.
• Remove the control cable fixing clip.
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. Adjust the control cables.
Air source control cable
1) Slide the control lever to the left (“CIRC” posi-
tion).
2) Connect the control cable at the “CIRC” posi-
tion of the link unit of blower assembly and fix it
with the clip.
Temperature control cable
1) Slide the control lever to the left/right (“MAX
COLD”/“MAX HOT” position).
N1A0038E
N1A0039E
Legend
1. A/C switch
2. Control lever
3. Catch
N1A0040E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст