Isuzu Trooper (2000 year). Service manual — part 501
8H–24 SECURITY AND LOCKS
Keyless Entry System
ID Code Registration
There are four kinds of ID codes which can be registered,
for which these two modes, ID code new registration and
ID code additional registration, are available.
ID Code New Registration
This procedure erases all registered ID codes and
registers a new received ID code instead.
Step
Action
Yes
No
1
1. Confirm that all the doors are closed and unlocked.
2. Open the driver’s side door.
3. Insert the key into the starter switch.
Is the action complete?
Go to Step 2
Go to Step 1
2
Turn the starter switch to ACC position and then to OFF position
three times.
NOTE: This step must be carried out within five seconds after step
1.
Is the action complete?
Go to Step 3
Go to Step 1
3
Close the driver’s side door and then open it two times.
NOTE: This step must be carried out within ten seconds after step
2.
Is the action complete?
Go to Step 4
Go to Step 1
4
1. Turn the starter switch to ACC position and then to OFF
position five times.
2. Close the driver’s side door and then open it.
NOTE: This step must be carried out within ten seconds after step
3.
Is the action complete?
Go to Step 5
Go to Step 1
5
The control unit locks and unlocks the doors one time.
Does the control unit work normally?
Go to Step 6
Go to Step 1
6
Operate the lock or unlock button of the transmitter.
NOTE: This step must be carried out within twenty seconds after
step 5.
Is the action complete?
Go to Step 7
Go to Step 1
7
The control unit locks and unlocks the doors one time.
Does the control unit work normally?
Go to Step 8
Go to Step 1
SECURITY AND LOCKS
8H–25
Step
No
Yes
Action
8
Operate the lock or unlock button of the transmitter.
NOTE: This step must be carried out within twenty seconds after
step 7.
Is the action complete?
Go to Step 9
Go to Step 1
9
The control unit compares the two codes sent from the
transmitter.
If the code succeeds in registration, the control unit locks and
unlocks the doors one time.
If the two codes are different from each other or fails in
registration, the control unit locks and unlocks the doors three
times.
NOTE: In any case, this procedure is finished.
Go to Step 1
Go to Step 1
ID Code Additional Registration
This procedure additionally registers a new received ID
code with holding registered ID codes. When total
number of registered ID codes and newly registered ID
code exceeds four, they are erased in order of older one.
Step
Action
Yes
No
1
1. Confirm that all the doors are closed and unlocked.
2. Open the driver’s side door.
3. Insert the key into the starter switch.
Is the action complete?
Go to Step 2
Go to Step 1
2
Turn the starter switch to ACC position and then to OFF position
three times.
NOTE: This step must be carried out within five seconds after step
1.
Is the action complete?
Go to Step 3
Go to Step 1
3
Close the driver’s side door and then open it two times.
NOTE: This step must be carried out within ten seconds after step
2.
Is the action complete?
Go to Step 4
Go to Step 1
4
1. Turn the starter switch to ACC position and then to OFF
position three times.
2. Close the driver’s side door and then open it.
NOTE: This step must be carried out within ten seconds after step
3.
Is the action complete?
Go to Step 5
Go to Step 1
5
The control unit locks and unlocks the doors two times.
Does the control unit work normally?
Go to Step 6
Go to Step 1
6
Operate the lock or unlock button of the transmitter.
NOTE: This step must be carried out within twenty seconds after
step 5.
Is the action complete?
Go to Step 7
Go to Step 1
7
The control unit locks and unlocks the doors one time.
Does the control unit work normally?
Go to Step 8
Go to Step 1
8H–26 SECURITY AND LOCKS
Step
No
Yes
Action
8
Operate the lock or unlock button of the transmitter.
NOTE: This step must be carried out within twenty seconds after
step 7.
Is the action complete?
Go to Step 9
Go to Step 1
9
The control unit compares the two codes sent from the
transmitter.
If the code succeeds in registration, the control unit locks and
unlocks the doors one time.
If the two codes are different from each other or fails in
registration, the control unit locks and unlocks the doors three
times.
NOTE: In any case, this procedure is finished.
Go to Step 1
Go to Step 1
Anti–theft & Keyless Entry Control
Unit/Transmitter Replacement
Anti–theft & Keyless Entry Control Unit
Replacement
1. Remove and install the control unit.
D
Refer to Anti–theft & Keyless Entry Control Unit
Removal and Installation in this section.
2. Register ID code.
D
Refer to ID Code Registration in this section.
3. Check that the keyless entry system works normally.
Transmitter Replacement
1. Prepare a new transmitter.
2. Regiter ID code.
D
Refer to ID Code Registration in this section.
3. Check that the keyless entry system works normally.
Transmitter Battery Replacement
1. Remove a screw to remove the cover.
2. Remove the batteries.
3. Set the new batteries into the transmitter.
4. Install the cover to the transmitter.
5. Check that the keyless entry system works normally.
SECURITY AND LOCKS
8H–27
Main Data and Specifications
Torque Specifications
Application
N·m
Lb Ft
Lb In
Front Door Lock Assembly Fixing Screws
7
—
61
Front Outside Handle and Key Switch Fixing Bolts
9
—
78
Rear Door Lock Assembly Fixing Screws
7
—
61
Rear Outside Handle Fixing Bolts
9
—
78
Tailgate Lock Assembly (LH) Fixing Screws
7
—
61
Tailgate Lock Assembly (RH) Fixing Bolts
11
—
95
Tailgate Outside Handle and Key Cylinder Fixing Bolts
9
—
78
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст