Isuzu Trooper (1998-2002 year). Service manual — part 1054
8H–2
SECURITY AND LOCKS
Service Precaution
WARNING: IF SO EQUIPPED WITH A
SUPPLEMENTAL RESTRAINT SYSTEM (SRS),
REFER TO THE SRS COMPONENT AND WIRING
LOCATION VIEW IN ORDER TO DETERMINE
WHETHER YOU ARE PERFORMING SERVICE ON OR
NEAR THE SRS COMPONENTS OR THE SRS
WIRING. WHEN YOU ARE PERFORMING SERVICE
ON OR NEAR THE SRS COMPONENTS OR THE SRS
WIRING, REFER TO THE SRS SERVICE
INFORMATION. FAILURE TO FOLLOW WARNINGS
COULD RESULT IN POSSIBLE AIR BAG
DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.
Front Door Lock Assembly
Front Door Lock Assembly and Associated Parts
632RS003
Legend
(1) Door Trim Panel
(2) Waterproof Sheet
(3) To Outside Handle
(4) Rear Guide Rail
(5) Door Lock Assembly
(6) Door Lock Switch Connector (W/Power Door
Lock)
Removal
1. Disconnect the battery ground cable.
2. Remove the door trim panel.
3. Remove the waterproof sheet.
Refer to the Front Window Regulator, Glass And
Glass Run in Body Structure section.
SECURITY AND LOCKS
8H–3
4. Raise the glass up to the uppermost position, and
then remove the rear guide rail.
5. Disconnect the door lock switch connector (w/power
door lock) and locking links (arrow marks positions),
then remove the door lock assembly fixing screws
and door lock assembly.
632RS004
Legend
(1) To Inside Lock Knob
(2) Door Lock Assembly
(3) To Actuator
(4) Door Lock Switch Connector
(5) To Inside Handle
(6) Outside Handle
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Apply chassis grease to the lock assembly and striker
moving surface.
2. Tighten the door lock assembly fixing screws to the
specified torque.
Torque: 7 N·m (0.7kg·m/61 lb in)
3. Check that the door lock operates smoothly.
8H–4
SECURITY AND LOCKS
Front Outside Handle and Door Lock Cylinder
Front Outside Handle, Door Lock Cylinder and Associated Parts
632RS006
Legend
(1) Door Trim Panel
(2) Waterproof Sheet
(3) Outside Handle
(4) Door Lock Cylinder
(5) Clip
(6) Key Switch (W/Anti-Theft)
Removal
1. Disconnect the battery ground cable.
2. Remove the door trim panel.
3. Remove the waterproof sheet.
D
Refer to the Front Window Regulator, Glass And
Glass Run in Body Structure section.
SECURITY AND LOCKS
8H–5
4. Disconnect the locking links (arrow marks positions)
and key switch connector (w/anti-theft) to remove the
outside handle.
632RS005
Legend
(1) Outside Handle
(2) To Door Lock Assembly
(3) Key Switch Connector (W/Anti–Theft)
5. Remove the key Switch.
632RS007
Legend
(1) Outside Handle
(2) Lock Cylinder
(3) Key Switch
6. Remove the fixing clip(1) to remove the door lock
cylinder(2).
632RS009
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Be sure to install the door lock cylinder(2) at a right
angle to the outside handle(1).
632RS008
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст