Mercedes-Benz ML320. Service manual — part 795
AR91.12-P-1730GI
Remove and install locking mechanism for folding rear seat backrest
5.5.99
MODELS 163.136 /154 /172 as of 1.9.99,
163.113 /128 /157 /174 /175
P91.12-2133-06
1
Rear backrest release cable
2
Adjuster
3
Screws
4
Bolts
5
Rear backrest fitting
Remove/Install
1
Remove side covers at rear backrest
fitting (5)
2
Detach rear seat backrest release cable (1) at
adjuster (2)
Mark adjustment position on the thread.
Turn the adjuster counterclockwise until the
rear backrest release cable can be unhooked.
3
Unscrew bolts (3) from rear backrest fitting
With 60% rear seat: Unscrew bolts (3) at
the same time in order to prevent the rear
backrest fitting from tipping.
*BA91.12-P-1006-03A
4
Unscrew bolts (4) from rear backrest fitting
*BA91.12-P-1007-03A
Torx bit set
*000589011000
5
Remove backrest fitting (5)
6
Install in the reverse order
Installation: check unlocking function of
folding rear backrest.
Rear seats
Number
Designation
Model
163 as of
09/99
BA91.12-P-1006-03A
Bolt from backrest fitting to backrest
Nm
30
BA91.12-P-1007-03A
Screw for backrest fitting on seat frame
Nm
30
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
Torx bit set
000 589 01 10 00
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 2
AR91.12-P-1720GI
Remove/install tilting rear seat
3.5.99
MODEL
163.136 /154 /172 as of 1.9.99,
163.113 /128 /157 /174 /175
P91.12-2128-09
1
Cushion below arm rest
2
Bolts
7
Center seat belt
8
Seat belt bolt
9
Rear seat cushion
10
Belt end fitting
3
Covers
4
Bolts
5
Bolts
6
Backrest
Remove, Install
1
Remove headrests
See Operating Instructions
2
Remove rear cargo space floor flaps
See Operating Instructions
3
Fold other bench down into the footwell
See Operating Instructions
4.1
Remove cushion (1) from underneath arm rest
Applies to 60% seat bench only.
Unscrew 2 bolts on the bottom of the rear
side, and turn upholstery upwards, in order to
detach locating tab at the rear.
5
Remove screws (2) for covering (3)
6
Remove covers (3) from backrest fitting
7
Remove screws (4) on backrest fitting
60 % bench: Fold backrest down, in order
to gain access to the screws on inside of the
backrest fitting.
Torx bit set
*000589011000
*BA91.12-P-1006-03A
8
Fold bench seat into footwell
Rear seat backrest remains erect.
9
Remove screw (5) on backrest bracket
Pull handle forward.
Torx bit set
*000589011000
*BA91.12-P-1006-03A
10
Remove rear seat backrest (6) from bench
Put rear seat backrest down in the load
compartment.
11.1
Detach seat upholstery from back of rear seat
cushion (9)
Applies to 60% seat bench only.
12.1
Carefully lift seat upholstery upwards and
remove seat belt screw (8) on belt end fitting
(10) on the rear seat bench frame
Take care not to damage seat upholstery.
Applies to 60% seat bench only.
Torx bit set
*000589011000
*BA91.40-P-1001-01D
13.1
Remove buckle connector from seat frame
and withdraw from retaining clamp
Only 60 % bench seat in combination with
rear side airbag (left and right), code 293. In
order to avoid fault codes, turn ignition key to
the "0" position.
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 1
14.1
Remove belt end fitting (10) together with
buckle through the rear seat cushion (9)
Do not damage seat cover!
Applies to 60% seat bench only.
15
Install in the reverse order
Rear seats
Number
Designation
Model
163 as of
09/99
BA91.12-P-1006-03A
Bolt for backrest fitting to rear seat backrest
Nm
30
Seat belts/belt tensioners
Number
Designation
Model 163 up to
08/99
Model 163 as of
09/99
BA91.40-P-1001-01D
Screw on belt end fitting
Nm
35
35
Torx bit set
000 589 01 10 00
Copyright DaimlerChrysler AG 14.06.2006 CD-Ausgabe G/10/04 . This WIS print-out will not be recorded by Modification services.
Page 2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст