Mercedes-Benz Sprinter / Dodge Sprinter. Service manual — part 130
Symptom List:
P2025-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH
P2030-INTAKE PRESSURE SENSOR CIRCUIT FAULT
P2030-INTAKE PRESSURE SENSOR OPEN CIRCUIT
P2030-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH
Test Note:
All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P2025-INTAKE PRESSURE
SENSOR SIGNAL VOLTAGE TOO HIGH.
POSSIBLE CAUSES
INTERMITTENT CONDITION
INTAKE PRESSURE SENSOR GROUND CIRCUIT SHORTED TO VOLTAGE
INTAKE PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
INTAKE PRESSURE SENSOR GROUND CIRCUIT OPEN
INTAKE PRESSURE SENSOR
ENGINE CONTROL MODULE (INTERNAL)
ENGINE CONTROL MODULE (SENSOR SIGNAL SHORTED TO VOLTAGE)
TEST
ACTION
APPLICABILITY
1
NOTE: If the ECM detects and stores a DTC, the ECM also stores the
engine/vehicle operating conditions under which the DTC was set. Some of
these conditions are displayed on the DRB at the same time the DTC is
displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to
duplicate these conditions may assist when checking for an active DTC.
NOTE: Ensure all turbocharger inlet and outlet tubes are connected prop-
erly, without damage and restriction before continuing with this test. Also
ensure the Boost Pressure Servo Motor and Servo Motor rod are attached
and functioning properly.
Turn the ignition on.
With the DRB, erase ECM DTCs.
Cycle the ignition key on and off several times, leaving the key on for at least 10
seconds at a time.
With the DRB, read ECM DTCs.
Did this DTC set again?
All
Yes
→ Go To 2
No
→ Go To 7
128
DRIVEABILITY - DIESEL
TEST
ACTION
APPLICABILITY
2
Turn the ignition off.
Disconnect the Intake Pressure Sensor harness connector.
Disconnect the ECM harness connectors.
Turn the ignition on.
Measure the voltage between ground and the Intake Pressure Sensor Signal circuit.
Is the voltage above 1.0 volt?
All
Yes
→ Go To 3
No
→ Go To 4
3
Turn the ignition off.
Disconnect the Intake Pressure Sensor harness connector.
Disconnect the ECM harness connectors.
Remove the Engine Control Relay.
Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay
connector.
Turn the ignition on.
Measure the voltage between ground and the Intake Pressure Sensor Signal circuit.
Is the voltage above 1.0 volt?
All
Yes
→ Repair the Intake Pressure Sensor Signal circuit for a short to
voltage.
Perform ROAD TEST VERIFICATION - VER-2.
No
→ Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.
4
Turn the ignition off.
Disconnect the Intake Pressure Sensor harness connector.
Disconnect the ECM harness connectors.
Remove the Engine Control Relay.
Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay
connector.
Turn the ignition on.
Measure the voltage between ground and the Intake Pressure Sensor Ground circuit.
Is the voltage above 1.0 volt?
All
Yes
→ Repair the Intake Pressure Sensor Ground circuit for a short to
voltage. Note: The ECM will need to be checked for proper
operation before the repair is completed. A short to voltage on a
ground circuit can damage the ECM.
Perform ROAD TEST VERIFICATION - VER-2.
No
→ Go To 5
5
Turn the ignition off.
Disconnect the Intake Pressure Sensor harness connector.
Disconnect the ECM harness connectors.
Measure the resistance of the Sensor Ground circuit.
Is the resistance below 10.0 ohms?
All
Yes
→ Go To 6
No
→ Repair the Intake Pressure Sensor Ground circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.
129
DRIVEABILITY - DIESEL
P2025-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH —
Continued
TEST
ACTION
APPLICABILITY
6
Turn the ignition off.
NOTE: Ensure all harness connectors are connected.
Turn the ignition on.
Measure the voltage of the Intake Pressure Sensor Signal circuit by back probing
ECM harness connector.
Is the voltage above 4.85 volts?
All
Yes
→ Replace the Intake Pressure Sensor.
Perform ROAD TEST VERIFICATION - VER-2.
No
→ Replace and program the Engine Control Module in accordance
with the Service Information.
Perform ROAD TEST VERIFICATION - VER-2.
7
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the
conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?
All
Yes
→ Repair as necessary.
Perform ROAD TEST VERIFICATION - VER-2.
No
→ Test Complete.
130
DRIVEABILITY - DIESEL
P2025-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH —
Continued
Symptom List:
P2025-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW
P2030-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW
Test Note:
All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P2025-INTAKE PRESSURE
SENSOR SIGNAL VOLTAGE TOO LOW.
POSSIBLE CAUSES
INTERMITTENT CONDITION
INTAKE PRESSURE SENSOR 5 VOLT SUPPLY
INTAKE PRESSURE SENSOR
INTAKE PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
INTAKE PRESSURE SENSOR SIGNAL AND GROUND CIRCUITS SHORTED TOGETHER
ENGINE CONTROL MODULE
INTAKE PRESSURE SENSOR SIGNAL CIRCUIT OPEN
TEST
ACTION
APPLICABILITY
1
NOTE: If the ECM detects and stores a DTC, the ECM also stores the
engine/vehicle operating conditions under which the DTC was set. Some of
these conditions are displayed on the DRB at the same time the DTC is
displayed.
NOTE: Before erasing stored DTCs, record these conditions. Attempting to
duplicate these conditions may assist when checking for an active DTC.
NOTE: Ensure all turbocharger inlet and outlet tubes are connected prop-
erly, without damage and restriction before continuing with this test. Also
ensure the Boost Pressure Servo Motor and Servo Motor rod are attached
and functioning properly.
Turn the ignition on.
With the DRB, erase ECM DTCs.
Cycle the ignition key on and off several times, leaving the key on for at least 10
seconds at a time.
With the DRB, read ECM DTCs.
Did this DTC set again?
All
Yes
→ Go To 2
No
→ Go To 7
2
Turn the ignition off.
Disconnect the Intake Pressure Sensor harness connector.
Turn the ignition on.
Measure the voltage between ground and the Intake Pressure Sensor 5 Volt Supply
circuit.
Is the voltage above 4.8 volts?
All
Yes
→ Go To 3
No
→ Repair the Intake Pressure Sensor 5 Volt Supply circuit for an
open.
Perform ROAD TEST VERIFICATION - VER-2.
131
DRIVEABILITY - DIESEL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст