Opel Adam (2019 year). Instruction — part 10
Vehicle care
151
Caution
When transporting the vehicle on
a train or on a recovery vehicle, the
mud flaps might be damaged.
Vehicle storage
Storage for a long period of time
If the vehicle is to be stored for several
months:
● Wash and wax the vehicle.
● Have the wax in the engine
compartment and underbody
checked.
● Clean and preserve the rubber
seals.
● Fill up fuel tank completely.
● Change the engine oil.
● Drain the washer fluid reservoir.
● Check the coolant antifreeze and
corrosion protection.
● Adjust tyre pressure to the value
specified for full load.
● Park the vehicle in a dry, well
ventilated place. Engage first or
reverse gear. Prevent the vehicle
from rolling.
● Do not apply the parking brake.
● Open the bonnet, close all doors
and lock the vehicle.
● Disconnect the clamp from the
negative terminal of the vehicle
battery. Beware that all systems
are not functional.
Putting back into operation
When the vehicle is to be put back into
operation:
● Connect the clamp to the
negative terminal of the vehicle
battery. Activate the electronics
of the power windows.
● Check tyre pressure.
● Fill up the washer fluid reservoir.
● Check the engine oil level.
● Check the coolant level.
● Fit the number plate if necessary.
End-of-life vehicle recovery
Information on end-of-life vehicle
recovery centres and the recycling of
end-of-life vehicles is available on our
website. Only entrust this work to an
authorised recycling centre.
Gas vehicles must be recycled by a
service centre authorised for gas
vehicles.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
152
Vehicle care
Vehicle checks
Performing work
9 Warning
Only perform engine compartment
checks when the ignition is off.
The cooling fan may start
operating even if the ignition is off.
9 Danger
The ignition system uses
extremely high voltage. Do not
touch.
Bonnet
Opening
Pull the release lever and return it to
its original position.
Push the safety catch upwards and
open the bonnet.
Secure the bonnet support.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
153
If the bonnet is opened during an
Autostop, the engine will be restarted
automatically for safety reasons.
Closing
Before closing the bonnet, press the
support into the holder.
Lower the bonnet and allow it to fall
into the latch from a low height
(20-25 cm). Check that the bonnet is
engaged.
Caution
Do not press the bonnet into the
latch, to avoid dents.
Engine oil
Check the engine oil level instructionly
on a regular basis to prevent damage
to the engine. Ensure that the correct
specification of oil is used.
Recommended fluids and lubricants
The maximum engine oil
consumption is 0.6 l per 1000 km.
Check with the vehicle on a level
surface. The engine must be at
operating temperature and switched
off for at least 5 minutes.
Pull out the dipstick, wipe it clean,
reinsert it fully, pull out and read the
engine oil level.
When the engine oil level has
dropped to the MIN mark, top up
engine oil.
We recommend the use of the same
grade of engine oil that was used at
last change.
The engine oil level must not exceed
the MAX mark on the dipstick.
Caution
Overfilled engine oil must be
drained or suctioned out. If the oil
exceeds the maximum level, do
not start the vehicle and contact a
workshop.
Capacities 3 208.
Fit the cap on straight and tighten it.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
154
Vehicle care
Engine coolant
The coolant provides freeze
protection down to approx. -28 °C. In
northern countries with very low
temperatures the factory filled coolant
provides frost protection down to
approx. -37 °C.
Caution
Only use approved antifreeze.
Coolant level
Caution
Too low a coolant level can cause
engine damage.
If the cooling system is cold, the
coolant level should be above the
filling line mark. Top up if the level is
low.
9 Warning
Allow the engine to cool before
opening the cap. Carefully open
the cap, relieving the pressure
slowly.
To top up use a 1:1 mixture of
released coolant concentrate mixed
with clean tap water. If no coolant
concentrate is available, use clean
tap water. Install the cap tightly. Have
the coolant concentration checked
and have the cause of the coolant
loss remedied by a workshop.
Washer fluid
Fill with clean water mixed with a
suitable quantity of approved
windscreen washer fluid which
contains antifreeze.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
155
Caution
Only washer fluid with a sufficient
antifreeze concentration provides
protection at low temperatures or
a sudden drop in temperature.
Washer fluid 3 199.
Brakes
In the event of minimum thickness of
the brake lining, a squealing noise
sounds during braking.
Continued driving is possible but
have the brake lining replaced as
soon as possible.
Once new brake linings are installed,
do not brake unnecessarily hard for
the first few journeys.
Brake fluid
9 Warning
Brake fluid is poisonous and
corrosive. Avoid contact with eyes,
skin, fabrics and painted surfaces.
The brake fluid level must be between
the MIN and MAX marks.
If fluid level is below MIN seek the
assistance of a workshop.
Brake and clutch fluid 3 199.
Vehicle battery
The vehicle battery is maintenance-
free provided that the driving profile
allows sufficient charging of the
battery. Short-distance-driving and
frequent engine starts can discharge
the vehicle battery. Avoid the use of
unnecessary electrical consumers.
Batteries do not belong in household
waste. They must be disposed of at
an appropriate recycling collection
point.
Laying up the vehicle for more than
four weeks can lead to vehicle battery
discharge. Disconnect the clamp from
the negative terminal of the vehicle
battery.
Ensure the ignition is switched off
before connecting or disconnecting
the vehicle battery.
Battery discharge protection 3 107.
Disconnecting the battery
If the vehicle's battery is to be
disconnected (e.g. for maintenance
work), the alarm siren must be
deactivated as follows: Switch the
ignition on then off, then disconnect
the vehicle's battery within
15 seconds.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
156
Vehicle care
Replacing the vehicle battery
Note
Any deviation from the instructions
given in this section may lead to
temporary deactivation or
disturbance of the stop-start system.
When the vehicle battery is being
replaced, please ensure that there
are no open ventilation holes in the
vicinity of the positive terminal. If a
ventilation hole is open in this area, it
must be closed off with a dummy cap,
and the ventilation in the vicinity of the
negative terminal must be opened.
Ensure that the battery is always
replaced by the same type of battery.
We recommend the use of an original
Opel battery.
Note
Using an AGM vehicle battery
different from the original Opel
vehicle battery may result in a lower
performance.
We recommend that you have the
vehicle battery replaced by a
workshop.
Charging the vehicle battery
9 Warning
On vehicles with stop-start
system, ensure that the charging
potential does not exceed 14.6 V
when using a battery charger.
Otherwise the vehicle battery may
be damaged.
Jump starting 3 191.
Stop-start system 3 120.
Warning label
Meaning of symbols:
● No sparks, naked flames or
smoking.
● Always shield eyes. Explosive
gases can cause blindness or
injury.
● Keep the vehicle battery out of
the reach of children.
● The vehicle battery contains
sulfuric acid which could cause
blindness or serious burn
injuries.
● See the Owner's instruction for
further information.
● Explosive gas may be present in
the vicinity of the battery.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
157
Wiper blade replacement
Windscreen
Lift the wiper arm until it stays in the
raised position, press button to
disengage the wiper blade and
remove.
Attach the wiper blade slightly angled
to the wiper arm and push until it
engages.
Lower wiper arm carefully.
Rear window
Lift wiper arm. Disengage wiper blade
as shown in illustration and remove.
Attach the wiper blade slightly angled
to the wiper arm and push until it
engages.
Lower wiper arm carefully.
Bulb replacement
Switch off the ignition and switch off
the relevant switch or close the doors.
Only hold a new bulb at the base! Do
not touch the bulb glass with bare
hands.
Use only the same bulb type for
replacement.
Replace headlight bulbs from within
the engine compartment.
Bulb check
After a bulb replacement switch on
the ignition, operate and check the
lights.
Halogen headlights
Halogen headlights with separate
bulbs for low beam and high beam.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
158
Vehicle care
Low beam outer bulb (1).
High beam inner bulb (2).
Low beam (1)
1. Rotate the cap anticlockwise and
remove it.
2. Press the clip to disengage bulb
holder. Withdraw the bulb holder
from the reflector.
3. Detach the bulb from the bulb
holder and replace the bulb.
4. Insert the bulb holder with the clip
downwards and engage into the
reflector until it clicks.
5. Install cap.
High beam (2)
1. Rotate the cap anticlockwise and
remove it.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
159
2. Press the clip to disengage bulb
holder. Withdraw the bulb holder
from the reflector.
3. Detach the bulb from the bulb
holder and replace the bulb.
4. Insert the bulb holder with the clip
upwards and engage into the
reflector until it clicks.
5. Install cap.
Sidelight / Daytime running light
with bulbs (3)
1. Rotate bulb socket (3)
anticlockwise to disengage.
Withdraw the bulb socket from the
headlamp housing.
2. Remove the bulb from the socket
by pulling.
3. Replace and insert new bulb into
socket.
4. Insert the bulb socket into the
headlamp housing and turn
clockwise.
Sidelight / Daytime running light
with LEDs
Sidelights and daytime running lights
consist of LEDs which cannot be
changed. Consult a workshop in case
of a defective LED.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
160
Vehicle care
Front turn lights
1. Undo screw and remove cover.
2. Undo screw and remove light
assembly from the bumper.
3. Disengage and remove the bulb
socket by turning anticlockwise.
4. Remove bulb by turning
anticlockwise slightly and
withdrawing. Replace the bulb.
5. Insert the bulb socket into the
assembly and turn clockwise.
6. Attach light assembly into the
bumper and fix with the screw.
7. Insert cover into the bumper and
fix with the screw.
Adam Rocks
1. Disengage the small cap with a
screwdriver at the marked
position.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
161
2. Remove the cover by pulling with
fingers at the marked positions,
see arrows in the illustration.
3. Undo both screws and remove
light assembly from the bumper.
4. Disengage and remove the bulb
socket by turning anticlockwise.
5. Remove bulb by turning
anticlockwise slightly and
withdrawing. Replace the bulb.
6. Insert the bulb socket into the
assembly and turn clockwise.
7. Attach light assembly into the
bumper and fix with both screws.
8. Insert and engage cover into the
bumper. Insert small cap.
Tail lights
Versions with subwoofer box
Remove the load compartment floor
cover. On right side also remove the
tool box to gain access to the cover
57.
Versions with storage box
Remove storage box to gain access
to the cover 3 56.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
162
Vehicle care
1. Release the cover on the
respective side and remove.
2. Unscrew the plastic securing nut
from the inside by hand.
3. Carefully withdraw the light
assembly from the recesses and
remove.
4. Turn bulb holder anticlockwise
and remove. Replace bulb by
withdrawing:
turn light 1
tail light 2
tail light / brake light 3
If tail light 2 and tail light / brake
light 3 are LEDs, seek the
assistance of a workshop for
replacement.
5. Insert and turn bulb holder
clockwise into the tail light
assembly. Ensure the wires
remain in the cable ducts.
Fit light assembly with the
retaining pins into the recesses of
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
163
the vehicle body and tighten the
plastic securing nut from inside
the load compartment. Pull the
circular gasket over the recess in
the lamp housing.
Close cover and engage.
Reversing light / rear fog light
Left-hand drive vehicles
Reversing light is located on the right
side of the bumper, and the rear fog
light is located on the left side of the
bumper.
Right-hand drive vehicles
Reversing light is located on the left
side of the bumper, and the rear fog
light is located on the right side of the
bumper.
The description of bulb replacement
is the same for both lights.
1. Undo screw and remove cover.
2. Undo screw and remove light
assembly from the bumper.
3. Disengage and remove the bulb
socket by turning anticlockwise.
4. Remove bulb by turning
anticlockwise slightly and
withdrawing. Replace the bulb.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
164
Vehicle care
5. Insert the bulb socket into the
assembly and turn clockwise.
6. Replace light assembly in the
bumper and fix with the screw.
7. Insert cover into the bumper and
fix with the screw.
Adam Rocks
1. Remove the cover by pulling by
hand at the marked position, see
arrow in the illustration.
2. Undo both screws and remove
light assembly from the bumper.
3. Disengage and remove the bulb
socket by turning anticlockwise.
4. Remove bulb by turning
anticlockwise slightly and
withdrawing. Replace the bulb.
5. Insert the bulb socket into the
assembly and turn clockwise.
6. Attach light assembly into the
bumper and fix with both screws.
7. Insert and engage cover into the
bumper.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
165
Side turn lights
To replace bulb, remove lamp
housing:
1. Slide lamp to its left side and
remove with its right end.
2. Turn bulb holder anticlockwise
and remove from housing.
3. Pull bulb from bulb holder and
replace it.
4. Insert bulb holder and turn
clockwise.
5. Insert left end of the lamp, slide to
the left and insert right end.
Number plate light
1. Insert screwdriver in recess of the
cover, press to the side and
release spring.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
166
Vehicle care
2. Remove lamp downwards, taking
care not to pull on the cable.
3. Remove bulb holder from lamp
housing by turning anticlockwise.
4. Pull bulb from bulb holder and
replace it.
5. Insert bulb holder into lamp
housing and turn clockwise.
6. Insert lamp into bumper and allow
it to engage.
Interior lights
Have the following bulbs replaced by
a workshop:
● courtesy light, reading lights
● load compartment light
● dome light
● ambient light
● starlight panel
● instrument panel illumination
Electrical system
Fuses
Data on the replacement fuse must
match the data on the defective fuse.
There are two fuse boxes in the
vehicle:
● in the front left of the engine
compartment,
● in left-hand drive vehicles behind
the light switch, or, in right-hand
drive vehicles, behind the
glovebox.
Before replacing a fuse, turn off the
respective switch and the ignition.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст