Opel Astra Saloon (2014 year). Instruction — part 11
166
Vehicle care
Wiper blade on the rear window
Lift the wiper arm. Disengage the
wiper blade and remove.
Bulb replacement
Switch off the ignition and switch off
the relevant switch or close the doors.
Only hold a new bulb at the base! Do
not touch the bulb glass with bare
hands.
Use only the same bulb type for
replacement.
The bulbs of the front outer lights are
replaced through openings in the
front wheel housing: turn wheels in a
way that allows access, release catch
and remove cover.
To replace bulbs on the right side of
the engine compartment, detach the
air hose from the air filter. On the left
side, detach the plug to the fuse box.
Halogen headlights
Headlights have separate systems for
high beam 1 (inner bulbs) and low
beam 2 (outer bulbs).
Low beam
1. Replace bulbs through the
opening in the wheel housing.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
167
2. Remove protective cover 2.
3. Rotate the bulb holder anti-
clockwise to disengage. Withdraw
the bulb holder from the reflector.
4. Detach bulb from bulb holder and
renew the bulb.
5. Insert the bulb holder, engaging
the two lugs into the reflector and
rotate clockwise to secure.
6. Rotate bulb carrier to the right as
far as it will go.
7. Install protective cover.
8. Close the opening in the wheel
housing with the cover.
High beam
1. Access to the bulbs is through the
engine compartment.
2. Remove protective cover 1.
3. Detach wiring plug from bulb.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
168
Vehicle care
4. Disengage spring clip from
retainer by pressing forward and
then swinging downwards.
5. Withdraw the bulb from reflector
housing.
6. When installing the new bulb,
insert lugs in the reflector
recesses and engage the spring
clip.
7. Install the wiring plug onto bulb.
8. Install protective cover.
Side lights
1. Access to the bulbs is through the
engine compartment.
2. Remove protective cover 1.
3. Withdraw parking light bulb holder
from reflector.
4. Remove bulb from socket and
renew the bulb.
5. Insert holder in reflector. Install
the headlamp protective cover.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
169
Xenon headlights
Headlamps have separate systems
for low beam 1 (inner bulbs) and high
beam 2 (outer bulbs).
Low beam
9 Danger
Low beam works under extremely
high electrical voltage. Do not
touch. Have bulbs replaced by a
workshop.
High beam
1. Replace bulbs through the
openings in the wheel arches.
2. Remove protective cover.
3. Rotate left bulb holder and
disengage.
4. Remove the bulb holder with bulb
from the reflector.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
170
Vehicle care
5. Detach bulb from bulb holder.
6. Insert new bulb so that the two
lugs on the bulb holder engage in
the recesses in the reflector.
7. Rotate bulb holder to the right as
far as it will go.
8. Place protective cover in position
and close.
Side lights
1. Replace bulbs through the
openings in the wheel arches.
2. Remove main beam headlight
protective cover.
3. Remove parking light socket from
reflector.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
171
4. Remove bulb from socket and
renew bulb.
5. Insert holder in reflector. Place
protective cap in position and
close.
Fog lights
Have bulbs replaced by a workshop.
Front turn signal lights
1. Replace the bulbs through the
opening in the wheel housing.
2. Rotate bulb holder anti-clockwise
and disengage.
3. Push bulb slightly into the socket,
rotate anti-clockwise, remove and
renew bulb.
4. Insert bulb holder in the reflector,
rotate clockwise and engage.
Tail lights
Saloon 5-door
1. To change the bulbs on the right
side, use a coin to open the lock
and fold down the cover.
To change bulbs on the left side,
use a coin to turn both locks and
2. Detach plug connector from bulb
holder.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
172
Vehicle care
3. Loosen fastening nuts with wheel
bolt wrench and unscrew by hand.
Vehicle tools 3 187.
4. Detach bulb housing towards the
rear.
5. Unscrew the three screws using a
screwdriver. Press the locking
tabs on the outside of the bulb
holder inwards and remove the
bulb holder.
6. Remove and renew the bulb.
Reverse light (1)
Turn signal light (2)
Reverse light/brake light (3)
Reverse light (4)
Fog light, may be only on one side
(5)
7. Engage bulb holder in bulb
housing, ensuring that it properly
engages.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
173
8. Ensure that the seals are applied
to the bulb holder and fixing
screws.
9. Insert the bulb housing in the
body, engaging the lug and the
ball pin in the recesses. Tighten
the fastening nuts using a wheel
bolt wrench. Attach the plug
connector. Close and engage the
flap.
Saloon 3-door
1. To change the bulbs, fold down
the cover.
2. Detach plug connector from bulb
holder.
3. Loosen fastening nuts with wheel
bolt wrench and unscrew by hand.
Vehicle tools 3 187.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
174
Vehicle care
4. Detach bulb housing towards the
rear.
5. Remove seal from the fastening
bolt. Press the locking tabs on the
outside of the bulb holder outward
and remove the bulb holder.
6. Remove and renew the bulb.
Reverse light (1)
Turn signal light (2)
Reverse light/brake light (3)
Reverse light (4)
Fog light, may be only on one side
(5)
7. Engage bulb holder in bulb
housing, ensuring that it properly
engages.
8. Ensure that the seals are applied
to the bulb holder and fixing
screws.
9. Insert the bulb housing in the
body, engaging the lug and the
ball pin in the recesses. Tighten
the fastening nuts using a wheel
bolt wrench. Attach the plug
connector. Close and engage the
flap.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
175
Saloon 4-door
1. To replace bulbs, fold up cover in
load compartment after twisting
the catch.
2. Release the bolts behind the
cover using a conventional bolt
wrench, and remove.
3. Unscrew the three screws with a
screwdriver and remove the bulb
holder. Vehicle tools 3 187.
4. Press tail lights back, holding the
bulb housing from the outside.
Remove plug from bulb carrier.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
176
Vehicle care
5. Press out six locking catches on
the bulb housing and remove bulb
carrier.
6. Remove and renew the bulb.
Brake light (1)
Reverse light (2)
Fog light, may be only on one side
(3)
Turn signal light (4)
Reverse light (5)
7. Engage bulb holder in bulb
housing. Ensure the seal is
applied correctly and the carrier
has engaged properly.
8. Attach the plug connector. Place
bulb housing in body, clipping the
round- head bolts into the
recesses. Attach bulb housing to
the body with four screws. Close
cover and lock.
Station wagon, Van
1. Disengage cover by pressing
retaining lugs and remove.
2. Detach plug connector from bulb
holder.
3. Loosen fastening nuts and
remove the bulb housing
rearwards.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
177
4. Unscrew the three screws with a
screwdriver and remove the bulb
holder. Vehicle tools 3 187.
5. Remove and renew the bulb.
Reverse light/brake light (1)
Turn signal light (2)
Reverse light (3)
Fog light, may be only on one side
(4)
6. Engage bulb holder in bulb
housing and screw in place. Insert
the bulb housing into the body and
tighten the fastening nuts by
hand.
Attach the plug connector.
Close and engage the cover.
TwinTop
1. Unscrew retaining nuts.
2. Remove bulb housing from
outside. Disengage plug by
pressing on flap and remove from
bulb holder.
3. Detach seal from bulb holder.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
178
Vehicle care
4. Disengage sockets by turning and
remove. Press locking tabs on the
long sides of the bulb holder
outwards; lift bulb holder at front
end and remove.
5. Remove and renew the bulb.
Reverse light/brake light (1)
Reverse light (2)
Fog light, may be only on one side
(3)
Reverse light (4)
Turn signal light (5)
6. Insert bulb holder in bulb housing
by first inserting the lug at the front
of the plug. Fold together bulb
holder, ensuring that it engages
properly. Insert sockets and
engage by turning.
7. Fit seal on bulb holder. Ensure
that the seal is flat in the area of
the screws.
8. Engage plug. Insert bulb housing
in body, ensuring proper
positioning of the ball pins in the
recesses. Tighten the retaining
nuts.
Side turn signal lights
Have the bulbs replaced by a
workshop.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
179
Number plate light
1. Insert a screwdriver in the
housing, press to the side and
release spring.
2. Remove bulb housing
downwards, taking care not to pull
on the cable.
3. Lift flap and disconnect wiring
plug from bulb holder.
4. Rotate bulb holder anti-clockwise
to disengage.
5. Remove bulb from holder and
renew bulb.
6. Insert bulb holder in bulb housing
and rotate clockwise.
7. Connect wiring plug to bulb
holder.
8. Insert and engage bulb housing.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
180
Vehicle care
Interior lights
Front courtesy light, reading
lights
1. Disengage lens, press it slightly
downwards and remove at a
downward angle.
2. Remove bulb and renew.
3. Engage lens.
Rear courtesy light and reading
lights
Have bulbs replaced by a workshop.
Glovebox light, load
compartment light, foot well light
1. Prise the lamp out with a
screwdriver.
2. Press bulb slightly towards spring
clip and remove.
3. Insert new bulb.
4. Install lamp.
Instrument panel
illumination
Have bulbs replaced by a workshop.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
181
Electrical system
Fuses
Data on the replacement fuse must
match data on the defective fuse.
The vehicle has two fuse boxes: one
behind a cover on the left side of the
load compartment and one in the front
left of the engine compartment.
Store spare fuses in the load
compartment fuse box version B.
Open the cover 3 185.
Before replacing a fuse, turn off the
respective switch and the ignition.
A blown fuse can be recognised by its
melted wire. Do not replace the fuse
until the cause of the fault has been
remedied.
Some functions are protected by
several fuses.
Fuses may also be inserted without
existence of a function.
Fuse extractor
A fuse extractor may be located in the
fuse box in the load compartment.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст