Opel Astra Saloon (2014 year). Instruction — part 8
118
Lighting
High beam
To switch from low to high beam,
push lever.
To switch to low beam, push lever
again or pull.
Headlight flash
To activate the headlight flash, pull
lever.
Headlight range
adjustment
Instruction headlight range
adjustment
To adapt headlight range to the
vehicle load to prevent dazzling:
Press knob to disengage and turn to
required position.
Vehicles without automatic level
control system
0 = front seats occupied
1 = all seats occupied
2 = all seats occupied and load
compartment laden
3 = driver's seat occupied and load
compartment laden
Vehicles with automatic level control
system
0 = front seats occupied
1 = all seats occupied
1 = all seats occupied and load
compartment laden
2 = driver's seat occupied and load
compartment laden
Automatic headlight range
adjustment
Headlight range is automatically
adjusted based on vehicle load.
Headlights when driving
abroad
The asymmetrical headlight beam
extends visibility at the edge of the
road on the passenger side.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
119
However, when driving in countries
where traffic drives on the opposite
side of the road, adjust the headlights
to prevent dazzling of oncoming
traffic.
Vehicles with halogen headlight
system
Have the headlights adjusted by a
workshop.
Vehicles with adaptive forward
lighting
Adapting the aim of the headlight
beam:
1. Pull lever and hold.
2. Switch on ignition.
3. An acoustic signal sounds after
approx. 3 seconds.
Control indicator B 3 101.
Daytime running lights
With the ignition on and the light
switch set to 7 or AUTO, the sidelights
are switched on. When the engine is
running, headlights illuminate.
On vehicle without automatic light
control, 9 must be switched on when
it gets dark for illumination of the
instrument panel.
The daytime running lights switch off
when the ignition is switched off.
Adaptive forward lighting
Adaptive forward lighting with Bi-
Xenon headlights improves lighting in
curves and increases headlight
range.
Curve lighting
The light beam pivots based on
steering wheel position and speed.
Motorway lighting
At higher speeds and continuous
straight ahead travel, the beam
automatically raises slightly, thereby
increasing headlight range.
Control indicator B 3 101.
Hazard warning flashers
Operated with the ¨ button.
The hazard warning flashers activate
automatically if the airbags deploy.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
120
Lighting
Turn and lane-change
signals
Lever up
= right turn signal
Lever down = left turn signal
The lever always springs back to its
original position.
If the lever is moved past the
resistance point, the turn signal is
switched on constantly. When the
steering wheel moves back, the turn
signal is automatically deactivated.
For three flashes, e.g. when changing
lanes, press the lever until resistance
is felt and then release.
Move the lever to the resistance point
and hold for longer indication.
Switch the turn signal off instructionly by
moving the lever slightly.
Front fog lights
The front fog lights can only be
switched on when both the ignition
and headlights or sidelights are on.
Operated with the > button.
Rear fog lights
The rear fog light can only be
switched on when both the ignition
and headlights or sidelights (with front
fog lights) are on.
Operated with the r button.
The vehicle rear fog light is
deactivated when towing.
Parking lights
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
121
When parked, the parking light on one
side can be activated:
1. Set light switch to 7 or AUTO.
2. Ignition off.
3. Move turn signal lever all the way
up (right parking light) or down
(left parking light).
Confirmed by a signal and the
corresponding turn signal control
indicator.
To switch it off, switch on the ignition
or move the turn signal lever in the
opposite direction.
Reversing lights
The reversing light comes on when
the ignition is on and reverse gear is
selected.
Misted light covers
The inside of the light covers may mist
up briefly in poor, wet and cold
weather conditions, in heavy rain or
after washing. The mist disappears
quickly by itself; to help, switch on the
headlights.
Interior lighting
Instrument panel
illumination control
Brightness can be adjusted when the
exterior lights are on: Press knob k to
disengage and then turn it and hold
until the desired brightness is
obtained.
Interior lights
During entry and exit of the vehicle,
the front and centre courtesy lights
automatically come on and then
switch off after a delay.
Front courtesy light
Operated with the c button.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
122
Lighting
Courtesy lights and rear reading
lights
Operated with switch.
I
= on
0
= off
centre = automatic
Reading lights
Operated with a buttons or switch.
I
= on
0
= off
centre = automatic
Sunvisor lights
The lighting switches on when the
cover is opened.
Lighting features
Centre console lighting
Spotlight in interior mirror housing.
Daylight-dependent, automatically
regulated centre console lighting.
Entry lighting
After unlocking the vehicle, the
instrument panel lighting and the
number plate lights come on for a few
seconds.
Starting off 3 17.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
123
Exit lighting
Headlights and reversing lights come
on for approx. 30 seconds after the
system is activated and the driver's
door is closed.
Activating
1. Switch off ignition.
2. Remove ignition key.
3. Open driver's door.
4. Pull turn signal lever.
5. Close driver's door.
If the driver's door is not closed the
lights switch off after two minutes.
The lighting is switched off
immediately if the turn signal lever is
pulled while the driver's door is open.
Battery discharge
protection
To prevent the battery from becoming
discharged, all the interior lighting is
switched off automatically after
10 minutes, when the ignition is
switched off.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
124
Climate control
Climate control
Climate control systems . . . . 124
Air vents . . . . . . . . . . 130
Maintenance . . . . . . . .. 131
Climate control systems
Heating and ventilation
system
Controls for:
■ Air distribution
■ Temperature
■ Fan speed
Heated rear window Ü 3 38.
Air distribution
L
= to head area and foot well
M
= to head area
l
= to windscreen and front door
windows
J
= to windscreen, front door
windows and foot well
K
= to foot well
Intermediate settings are possible.
Temperature
red = warm
blue = cold
Heating will not be fully effective until
engine has reached normal operating
temperature.
Fan speed
Adjust the air flow by switching the fan
to the desired speed.
Demisting and defrosting the
windows
■ Set air distribution control to l.
■ Set temperature control to warmest
level.
■ Set fan speed to highest level.
■ Switch on heated rear window Ü.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
125
■ Open side air vents as required and
direct them towards door windows.
■ For simultaneous warming of the
foot well, set air distribution control
to J.
Air conditioning system
In addition to the heating and
ventilation system, the air
conditioning system has:
n
= Cooling
4
= Air recirculation
Cooling n
Operated with the n button and is
functional only when the engine and
fan are running.
The air conditioning system cools and
dehumidifies (dries) as soon as the
outside temperature is slightly above
freezing point. Therefore
condensation may form and drip from
under the vehicle.
If no cooling or drying is required,
switch the cooling system off to save
fuel.
Air recirculation system 4
Operated with the 4 button.
9 Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling the air
humidity increases, so the
windows may mist up. The quality
of the passenger compartment air
deteriorates, which may cause the
vehicle occupants to feel drowsy.
Air distribution to l: Air recirculation
is deactivated.
Maximum cooling
Briefly open the windows so that hot
air can disperse quickly.
■ Cooling n on.
■ Air circulation system 4 on,
■ Set air distribution control to M.
■ Set temperature control to coldest
level.
■ Set fan speed to highest level.
■ Open all vents.
Demisting and defrosting the
windows
■ Cooling n on.
■ Set air distribution control to l.
■ Set temperature control to warmest
level.
■ Set fan speed to highest level.
■ Switch on heated rear window Ü.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
126
Climate control
■ Open side air vents as required and
direct them towards door windows.
■ For simultaneous warming of the
foot well, set air distribution control
to J.
Automatic climate control
system
Controls for:
■ Air distribution
■ Temperature
■ Fan speed
n
= Cooling
4
= Air recirculation
V
= Demisting and defrosting
Heated rear window Ü 3 38.
The preselected temperature is
automatically regulated. In the
automatic mode the fan speed
automatically regulates the air flow.
Automatic mode
Basic setting for maximum comfort:
■ Set fan control to A.
■ Set the air distribution control to the
desired setting.
■ Preset temperature to the desired
level.
■ Cooling n on.
■ Open all of the air vents.
Air distribution
L
= to head area and foot well
M
= to head area
l
= to windscreen and front door
windows
J
= to windscreen, front door
windows and foot well
K
= to foot well
Intermediate settings are possible.
Temperature preselection
Set the temperature control to the
required position. Intermediate
settings are possible.
For reasons of comfort, change
temperature only in small increments.
At the end positions, there is no
temperature regulation. The air
conditioning system works with
maximum cooling or heating.
Heating will not be fully effective until
engine has reached normal operating
temperature.
Fan speed
In the automatic mode A the fan
speed automatically regulates the air
flow. If required the air flow can be
instructionly adjusted.
Cooling n
Operated with the n button and is
functional only when the engine and
fan are running.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
127
The air conditioning system cools and
dehumidifies (dries) when outside
temperature is above a specific level.
Therefore condensation may form
and drip from under the vehicle.
If no cooling or drying is required,
switch the cooling system off to save
fuel.
Air recirculation system 4
The air recirculation mode is operated
with the 4 button.
9 Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling the air
humidity increases, so the
windows may mist up. The quality
of the passenger compartment air
deteriorates, which may cause the
vehicle occupants to feel drowsy.
Maximum cooling
Briefly open the windows so that the
heated air can disappear quickly.
■ Cooling n on.
■ Set air distribution control to M.
■ Set temperature control to required
temperature value.
■ Set fan control to A.
■ Open all vents.
The automatic climate control
automatically cools to the specified
value with the maximum cooling
power.
With the temperature control turned
to its minimum setting, the system
continually runs at maximum cooling.
The system is automatically set to air
recirculation when the air conditioning
is on.
Demisting and defrosting the
windows
■ Cooling n on.
■ Press button V: in position A, fan
automatically switches to maximum
speed, the air distribution is
directed towards the windscreen.
■ Set temperature control to warmest
level.
■ Switch on heated rear window Ü.
Electronic climate control
system
Controls for:
■ Temperature
■ Air distribution and menu selection
■ Fan speed
AUTO = Automatic mode
4
= air recirculation
V
= demisting and defrosting
-------------------------------------------------------------------------------------------------------------------------------------------------------------
128
Climate control
Heated rear window Ü 3 38.
The preselected temperature is
automatically regulated. In the
automatic mode the fan speed and air
distribution automatically regulate the
air flow.
The system can be instructionly adapted
by use of air distribution and air flow
controls.
Data is shown on the Info-Display.
Setting modifications are briefly
shown in the Info-Display,
superimposing over the currently
displayed menu.
The electronic climate control system
is only fully operational when the
engine is running.
Do not cover the sensor on the
instrument panel for correct
operation.
Automatic mode
Basic setting for maximum comfort:
■ Press AUTO button.
■ Open all air vents.
■ Air conditioning on.
■ Set desired temperature.
Temperature preselection
Temperatures can be set to the
desired value.
For reasons of comfort, change
temperature only in small increments.
If the minimum temperature is set,
Lo appears in the display and the
electronic climate control system runs
at maximum cooling.
If the maximum temperature is set,
Hi appears in the display and the
electronic climate control system runs
at maximum heating.
Fan speed
The selected fan speed is indicated
with x and a number in the display.
If the fan is switched off the air
conditioning is also deactivated.
To return to automatic mode: Press
AUTO button.
Demisting and defrosting the
windows
Press the V button. V appears in
the display.
Temperature and air distribution are
set automatically and the fan runs at
a high speed.
To return to automatic mode: press
button V or AUTO.
Switch on heated rear window Ü.
Instruction settings in climate menu
Climate control system settings can
be changed via the centre control, the
buttons and the menus shown on the
display.
To view the menu, press the centre
control. The Climate menu appears in
the display.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
129
Individual menu items are marked by
turning the centre control and
selected by pressing it.
To exit a menu, turn the centre control
until Return or Main appear and
select.
Air distribution
Turn the centre control. The Air
distribut. menu is activated, showing
the possible air distribution settings:
Top
= to windscreen and front
door windows.
Centre = to vehicle occupants.
Bottom = to foot well.
The Air distribut. menu can also be
called up via the Climate menu.
Return to automatic air distribution:
Deactivate corresponding setting or
press button AUTO.
Cooling
In the Climate menu, select menu
item AC and activate or deactivate
cooling.
The air conditioning system cools and
dehumidifies (dries) when outside
temperature is above a specific level.
Therefore condensation may form
and drip from under the vehicle.
If no cooling or drying is required,
switch the cooling system off to save
fuel, Eco appears in the display.
Fan regulation in automatic
mode
Fan regulation in automatic mode can
be adapted.
Select menu item Automatic blower
from the Climate menu and select the
desired fan regulation.
Instruction air recirculation mode
The instruction air recirculation mode is
operated with the 4 button.
9 Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling the air
humidity increases, so the
windows may mist up. The quality
of the passenger compartment air
deteriorates, which may cause the
vehicle occupants to feel drowsy.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
130
Climate control
Air conditioning with the engine
not running
When ignition is off, the residual heat
or cooling in the system can be used
for climate control in passenger
compartment.
Press the AUTO button with the
ignition off. Residual air conditioning
on will appear briefly in the display.
Residual climate control can only
operate for a limited period of time. To
cancel, press the AUTO button.
Auxiliary heater
Air heater
Quickheat is an electric auxiliary air
heater which warms up the
passenger compartment more
quickly.
Coolant heater
Diesel-engined vehicles have a fuel-
powered auxiliary heater.
Air vents
Adjustable air vents
At least one air vent must be open
while cooling is on in order to prevent
the evaporator from icing up due to
lack of air movement.
To open vent, turn the adjuster wheel
to B.
Direct the flow of air by tilting and
swivelling the slats.
To close the vent, turn the adjuster
wheel to 7.
9 Warning
Do not attach any objects to the
slats of the air vents. Risk of
damage and injury in case of an
accident.
Fixed air vents
Additional air vents are located
beneath the windscreen and door
windows and in the foot wells.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
131
Maintenance
Air intake
The air intakes in front of the
windscreen in the engine
compartment must be kept clear to
allow air intake. Remove any leaves,
dirt or snow.
Pollen filter
The pollen filter cleans dust, soot,
pollen and spores from the air
entering the vehicle through the air
intake.
Air conditioning regular
operation
In order to ensure continuously
efficient performance, cooling must
be operated for a few minutes once a
month, irrespective of the weather
and time of year. Operation with
cooling is not possible when outside
temperature is too low.
Service
For optimal cooling performance, it is
recommended to annually check the
climate control system, starting
three years after initial vehicle
registration, including:
■ Functionality and pressure test
■ Heating functionality
■ Leakage check
■ Check of drive belts
■ Cleaning of condenser and
evaporator drainage
■ Performance check
-------------------------------------------------------------------------------------------------------------------------------------------------------------
132
Driving and operating
Driving and operating
Driving hints . . . . . . . ... 132
Starting and operating . . . ... 132
Engine exhaust . . . . . . .. 135
Automatic transmission . . . .. 136
Manual transmission . . . . .. 141
Manual transmission automa‐
ted . . . . . . . . . . . .. 142
Brakes . . . . . . . . . . 146
Ride control systems . . . . . 147
Cruise control . . . . . . . . 149
Object detection systems . . ... 150
Fuel . . . . . . . . . . . 151
Trailer hitch . . . . . . . . 154
Driving hints
Control of the vehicle
Never coast with engine not
running
Many systems will not function in this
situation (e.g. brake servo unit, power
steering). Driving in this manner is a
danger to yourself and others.
Pedals
To ensure the pedal travel is
uninhibited, there must be no mats in
the area of the pedals.
Starting and operating
New vehicle running-in
Do not brake unnecessarily hard for
the first few journeys.
During the first drive, smoke may
occur because of wax and oil
evaporating off the exhaust system.
Park the vehicle in the open for a
while after the first drive and avoid
inhaling the fumes.
Fuel and engine oil consumption may
be higher during the running-in
period.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Driving and operating
133
Ignition switch positions
0 = Ignition off
1 = Steering wheel lock released,
ignition off
2 = Ignition on, for diesel engine:
preheating
3 = Starting
Starting the engine
Starting engine with ignition
switch
Operate clutch and brake, automatic
transmission in P or N, do not
accelerate; for diesel engines, turn
the key to position 2 for preheating
until control indicator ! goes out;
turn key briefly to position 3 and
release key when engine is running.
Before restarting or to switch off the
engine, turn key back to position 0.
Starting engine with the
Start/Stop button
The electronic key must be inside the
vehicle. Operate clutch and brake,
automatic transmission in P or N, do
not accelerate, for diesel engines,
press the button briefly to start
preheating, move the steering wheel
slightly to release the steering wheel
lock, wait until control indicator !
goes out and then press button for
1 second and release when the
engine is running.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст