Opel Mokka X (2019 year). Instruction — part 4
54
Seats, restraints
When the child restraint system is not
in use, secure the seat with a seat belt
or remove it from the vehicle.
Note
Do not affix anything on the child
restraint systems and do not cover
them with any other materials.
A child restraint system which has
been subjected to stress in an
accident must be replaced.
Child restraint systems can be
fastened with:
● Three-point seat belt
● ISOFIX brackets
● Top-tether anchor
Three-point seat belt
Child restraint systems can be
fastened by using a three-point seat
belt. Depending on the size of the
used child restraint systems, up to
three child restraint systems can be
attached to the rear seats. After
fastening the child restraint system
the seat belt has to be tightened
ISOFIX child restraint systems
For the installation of ISOFIX child
restraint systems, two variants are
available:
● Installation of ISOFIX child
restraint systems without
permanent guide
● Installation of ISOFIX child
restraint systems with permanent
guide
Installation of ISOFIX child restraint
systems without permanent guide
Fasten vehicle-approved ISOFIX
child restraint systems to the ISOFIX
mounting brackets. Specific vehicle
ISOFIX child restraint system
positions are marked in the table by
IL.
ISOFIX mounting brackets are
indicated by a label on the backrest.
Installation of ISOFIX child restraint
systems with permanent guide
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Seats, restraints
55
The vehicle might be equipped with
guides in front of the mounting
brackets to support the installation of
the child restraint system.
The covers of the guides will swivel
backwards automatically when
attaching the child restraint system.
Top-tether anchors
Depending on country specific
equipment, the vehicle might have
two or three fastening eyes.
Top-Tether anchors are marked with
the symbol : for a child restraint.
For non-ISOFIX child restraints,
fasten the Top-Tether strap to the
Top-Tether anchors.
For ISOFIX child restraints, fasten the
Top-Tether strap to the Top-Tether
anchors in addition to the ISOFIX
mounting.
ISOFIX child restraint systems of
universal category positions are
marked in the table by IUF.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
56
Seats, restraints
Child restraint installation locations
Permissible options for fitting a child restraint system
Weight class
On front passenger seat
On rear outboard seats
On rear centre seat
activated airbag
deactivated airbag
Group 0: up to 10 kg
X
U
1
U
2
U
2
Group 0+: up to 13 kg
X
U
1
U
2
U
2
Group I: 9 to 18 kg
X
U
1
U
2
U
2
Group II: 15 to 25 kg
X
X
U
2
U
2
Group III: 22 to 36 kg
X
X
U
2
U
2
1
: if the child restraint system is being secured using a three-point seat belt, move seat height adjustment to uppermost
position and ensure that vehicle seat belt runs forwards from the upper anchorage point. Adjust seat backrest
inclination as far as necessary to a vertical position to ensure that the belt is tight on the buckle side.
2
: move the head restraint to uppermost position. If it interferes with the proper installation of the child restraint system,
remove the head restraint 3 39.
U : universal suitability in conjunction with three-point seat belt.
X : no child restraint system permitted in this weight class.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Seats, restraints
57
Permissible options for fitting an ISOFIX child restraint system
Weight class
Size class Fixture
On front passenger seat On rear outboard seats On rear centre seat
Group 0: up to 10 kg
E
ISO/R1 X
IL
1
X
Group 0+: up to 13 kg E
ISO/R1 X
IL
1
X
D
ISO/R2 X
IL
1
X
C
ISO/R3 X
IL
1
X
Group I: 9 to 18 kg
D
ISO/R2 X
IL
1
X
C
ISO/R3 X
IL
1
X
B
ISO/F2
X
IL, IUF
X
B1
ISO/F2X X
IL, IUF
X
A
ISO/F3
X
IL, IUF
X
Group II: 15 to 25 kg
X
IL
X
Group III: 22 to 36 kg
X
IL
X
1
: move front passenger seat to the foremost position or adjust front seat backrest inclination as far as necessary to
a vertical position to ensure that there is no interference between child restraint system and front seat backrest.
IL : suitable for particular ISOFIX restraint systems of the "specific-vehicle", "restricted" or "semi-universal" categories.
The ISOFIX restraint system must be approved for the specific vehicle type.
IUF : suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weight class.
X
: no ISOFIX child restraint system approved in this weight class.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
58
Seats, restraints
ISOFIX size class and seat device
A – ISO/F3
: forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg
B – ISO/F2
: forward-facing child restraint system for smaller children in the weight class 9 to 18 kg
B1 – ISO/F2X : forward-facing child restraint system for smaller children in the weight class 9 to 18 kg
C – ISO/R3
: rear-facing child restraint system for children of maximum size in the weight class up to 18 kg
D – ISO/R2
: rear-facing child restraint system for smaller children in the weight class up to 18 kg
E – ISO/R1
: rear-facing child restraint system for young children in the weight class up to 13 kg
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Storage
59
Storage
Storage compartments . . . . 59
Glovebox . . . . . . . . ... 59
Cupholders . . . . . . . . 59
Front storage . . . . . . . . 60
Underseat storage . . . . . . 60
Centre console storage . . . . 61
Rear carrier system . . . . ... 61
Load compartment . . . . . ... 71
Load compartment cover . . ... 72
Rear floor storage cover . . . 73
Lashing eyes . . . . . . . . 73
Warning triangle . . . . . . 73
First aid kit . . . . . . . . . 73
Roof rack system . . . . . . . 74
Roof rack . . . . . . . . ... 74
Loading information . . . . . . 74
Storage compartments
9 Warning
Do not store heavy or sharp
objects in the storage
compartments. Otherwise, the
storage compartment lid could
open and vehicle occupants could
be injured by objects being thrown
around in the event of hard
braking, a sudden change in
direction or an accident.
Glovebox
To open, pull the handle.
The glovebox should be closed while
driving.
Cupholders
The cupholders are located in the
centre console and rear part of the
centre console.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
60
Storage
To use the rear seat cupholder, fold
down the rear seat armrest.
Front storage
A storage compartment is located
next to the steering wheel. Pull the
handle to open.
A further storage compartment is
located in the centre console.
To open, press the button.
The covers of the storage
compartments should be closed while
driving.
Underseat storage
Lift drawer at the front and pull out. To
close, push the drawer in and
engage.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Storage
61
Centre console storage
Push down the button and slide cover
backwards.
Rear carrier system
Rear carrier system for three
bicycles
The rear carrier system (Flex-Fix
system) allows one bicycle to be
attached to an extendable carrier
integrated into the vehicle floor. It is
possible to attach two further bicycles
on an adapter. The transportation of
other objects is not permitted.
The maximum load of the rear carrier
system is 60 kg with attached adapter
and 30 kg without attached adapter.
This allows the attachment of an
electrically-powered bicycle to the
rear carrier system. The maximum
load per bicycle on the adapter is
20 kg.
The wheelbase of a bicycle must not
exceed 1.15 m. Otherwise the secure
fastening of a bicycle is not possible.
If not in use, the rear carrier system
must be slid back into the vehicle
floor.
There must not be any objects on the
bicycles that could become loose
during transportation.
Caution
If the rear carrier system is
extended and the vehicle is fully
loaded, the ground clearance will
be reduced.
Drive carefully whenever the road
has a steep inclination or when
driving over a ramp, bump, etc.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
62
Storage
Caution
Consult your bicycle dealer before
attaching bicycles with carbon
frames. The bicycles may get
damaged.
Note
The tail lights of the vehicle will be
deactivated if the tail lights of the
rear carrier system are installed.
Extending
Open the tailgate.
9 Warning
No-one should be in the extension
zone of the rear carrier system,
risk of injury.
Pull release lever up. The rear carrier
system disengages and travels
quickly out of the rear bumper.
Completely pull out the rear carrier
system until you hear it engage.
Ensure that it is not possible to push
in the rear carrier system without
pulling the release lever again.
9 Warning
It is only permissible to fit objects
to the rear carrier system if the
system has been correctly
engaged. If the rear carrier system
will not engage correctly, do not fit
objects to the system and slide the
system back. Seek the assistance
of a workshop.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Storage
63
Unfold number plate holder
Lift the number plate holder and fold
it backwards.
Affix the number plate before first use
of the rear carrier system.
Fold out tail lights
To install the tail lights, remove both
pins (1). Pull tail lights out of the
retainer towards the front (2) and
downwards and swivel them to the
side.
Push the tail lights into the retainer
(1) and reinstall pins (2) all the way to
attach the lights.
Fold out wheel recess
-------------------------------------------------------------------------------------------------------------------------------------------------------------
64
Storage
Remove strap and fold out the wheel
recess.
Lock the rear carrier system
Remove strap and swivel both
clamping levers sideways as far as
they will go.
Otherwise safe functionality is not
guaranteed.
Assembling the bicycle rack
Lift the rack at the rear (1) and pull it
backwards.
Fold up the rack (2).
Push down the rack (1) and swivel
handle (2) backwards to engage.
Press button (1) and remove left part
of rack (2).
Press button (1) and insert left part of
rack into the right part (2).
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Storage
65
Attaching a bicycle
1. Rotate the pedals into position, as
shown in the illustration, and put
the bicycle on the wheel recess.
Make sure that the bicycle stands
centrally on the wheel recesses.
2. Attach the short mounting bracket
to the bicycle frame. Turn the
knob clockwise to fasten.
3. Secure both bicycle wheels to the
wheel recesses using the strap
retainers.
4. Check the bicycle to make sure it
is secure.
Caution
Ensure gap between bicycle and
vehicle is at least 5 cm. If
necessary, loosen handlebar and
swivel sideways.
Attaching the adapter
When carrying more than one bicycle,
the adapter must be fixed.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
66
Storage
1. Apply the adapter to the rear
carrier system, as shown in the
illustration.
2. Turn the lever (1) forwards and
hold it, then lower the adapter (2)
at the rear.
3. Release lever and check if the
adapter is engaged securely.
4. Guide the strap attached to the
adapter underneath the lever
when folding back the rear carrier
system. Fasten the strap.
Attaching further bicycles
The attachment of further bicycles is
similar to the attachment of the first
bicycle. Additionally, some steps
must be considered:
1. Before putting on the bicycle,
always unfold the wheel recesses
for the next bicycle if necessary.
2. Always rotate the pedals into an
appropriate position before
putting on the bicycle.
3. Position the bicycles on the rear
carrier system alternately aligned
to the left and to the right.
4. Align the bicycles with the one
attached previously. The wheel
hubs of the bicycles must not
touch each other.
5. Attach the bicycles with mounting
brackets and strap retainers as
described for the first bicycle. The
mounting brackets should be
fixed in parallel.
Use the long mounting bracket to
attach the second bicycle to the
rack.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Storage
67
Use the short accessory mounting
bracket to attach the third bicycle.
The bracket must be fixed
between the frames of the second
and third bicycle.
6. Additionally, secure both bicycle
wheels of the third bicycle to the
wheel recesses using the
tensioning straps.
It is recommended to attach a
warning sign to the rearmost bicycle,
to increase visibility.
Fold the rear carrier system
backwards
The rear carrier system can be folded
backwards to gain access to the load
compartment.
● Without attached adapter:
Push the lever (1) to disengage
and hold it.
Pull the rack (2) backwards to
fold the rear carrier system.
● With attached adapter:
9 Warning
Take care when disengaging the
rear carrier system as it will tilt
backwards. Risk of injury.
Hold frame (1) of rearmost
bicycle with one hand and pull the
loop (2) to disengage.
Hold rearmost bicycle with both
hands and fold the rear carrier
system backwards.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
68
Storage
To increase visibility, the tail lights of
the vehicle are activated when the
rear carrier system is folded back.
9 Warning
When folding the rear carrier
system forwards again, ensure
that the system is engaged
securely.
Removing bicycles
Undo strap retainers on both bicycle
tyres.
Turn knob anticlockwise and remove
mounting brackets.
Detaching adapter
Detach the adapter before removing
the bicycle on the rear carrier system.
1. Fold in wheel recesses.
2. Unbutton the strap.
3. Turn the lever (1) forwards and
hold it.
4. Lift the adapter (2) at the rear and
remove.
Disassembling the bicycle rack
Press button (1) and remove upper
part of rack (2).
Press button (1) and reinstall rack (2).
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Storage
69
Arrange mounting brackets as shown
in the illustration.
Swivel handle (1) sideways to
disengage and lift the rack (2).
Fold the rack backwards, then push
forwards until it stops (1).
Press the rack down at the rear (2).
Fold in wheel recess
Fold in wheel recess. Fasten strap.
Stow the strap retainers accurately.
Unlock the rear carrier system
Swivel both clamping levers inwards
as far as they will go. Fasten strap.
Fold in tail lights
Remove both pins. Pull tail lights out
of the retainer and put them in the
position to be stored in.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст