Opel Mokka X (2019 year). Instruction — part 12
182
Vehicle care
Vehicle checks
Performing work
9 Warning
Only perform engine compartment
checks when the ignition is off.
The cooling fan may start
operating even if the ignition is off.
9 Danger
The ignition system and Xenon
headlights use extremely high
voltage. Do not touch.
Bonnet
Opening
Pull the release lever and return it to
its original position.
Move the safety catch sideways to the
left vehicle side and open the bonnet.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
183
Pull up the support rod lightly from the
holder. And then secure it at the left
side hook on the bonnet.
If the bonnet is opened during an
Autostop, the engine will be restarted
automatically for safety reasons.
Closing
Before closing the bonnet, press the
support into the holder.
Lower the bonnet and allow it to fall
into the latch from a low height
(20-25 cm). Check that the bonnet is
engaged.
Caution
Do not press the bonnet into the
latch, to avoid dents.
Engine oil
Check the engine oil level instructionly
on a regular basis to prevent damage
to the engine. Ensure that the correct
specification of oil is used.
Recommended fluids and lubricants
The maximum engine oil
consumption is 0.6 l per 1000 km.
Check with the vehicle on a level
surface. The engine must be at
operating temperature and switched
off for at least 5 min.
Pull out the dipstick, wipe it clean,
insert it to the stop on the handle, pull
out and read the engine oil level.
Insert dipstick to the stop on the
handle.
When the engine oil level has
dropped to the MIN mark, top up
engine oil.
We recommend the use of the same
grade of engine oil that was used at
last change.
The engine oil level must not exceed
the MAX mark on the dipstick.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
184
Vehicle care
The engine oil filler cap is located on
the camshaft cover.
Caution
Overfilled engine oil must be
drained or suctioned out. If the oil
exceeds the maximum level, do
not start the vehicle and contact a
workshop.
Capacities 3 234.
Fit the cap on straight and tighten it.
Engine coolant
The coolant provides freeze
protection down to approx. -30 °C. In
northern countries with very low
temperatures the factory filled coolant
provides frost protection down to
approx. -40 °C.
Caution
Only use approved antifreeze.
Coolant level
Caution
Too low a coolant level can cause
engine damage.
If the cooling system is cold, the
coolant level should be above the
filling line mark. Top up if the level is
low.
9 Warning
Allow the engine to cool before
opening the cap. Carefully open
the cap, relieving the pressure
slowly.
To top up use a 1:1 mixture of
released coolant concentrate mixed
with clean tap water. If no coolant
concentrate is available, use clean
tap water. Install the cap tightly. Have
the coolant concentration checked
and have the cause of the coolant
loss remedied by a workshop.
Power steering fluid
Caution
Extremely small amounts of
contamination can cause steering
system damage and cause it to not
work properly. Do not allow
contaminates to contact the fluid
side of the reservoir cap / dipstick
or from entering the reservoir.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
185
Power steering fluid level normally
does not need to be checked. If an
unusual noise sounds during steering
or the power steering reacts
conspicuously, seek the assistance of
a workshop.
Washer fluid
Fill with clean water mixed with a
suitable quantity of approved
windscreen washer fluid which
contains antifreeze.
Caution
Only washer fluid with a sufficient
antifreeze concentration provides
protection at low temperatures or
a sudden drop in temperature.
Brakes
In the event of minimum thickness of
the brake lining, a squealing noise
sounds during braking.
Continued driving is possible but
have the brake lining replaced as
soon as possible.
Once new brake linings are installed,
do not brake unnecessarily hard for
the first few journeys.
Brake fluid
9 Warning
Brake fluid is poisonous and
corrosive. Avoid contact with eyes,
skin, fabrics and painted surfaces.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
186
Vehicle care
The brake fluid level must be between
the MIN and the MAX marks.
If fluid level is below MIN seek the
assistance of a workshop.
Brake and clutch fluid 3 222.
Vehicle battery
The vehicle battery is maintenance-
free provided that the driving profile
allows sufficient charging of the
battery. Short-distance-driving and
frequent engine starts can discharge
the battery. Avoid the use of
unnecessary electrical consumers.
Batteries do not belong in household
waste. They must be disposed of at
an appropriate recycling collection
point.
Laying up the vehicle for more than
four weeks can lead to battery
discharge. Disconnect the clamp from
the negative terminal of the vehicle
battery.
Ensure the ignition is switched off
before connecting or disconnecting
the vehicle battery.
Vehicle battery discharge protection
Replacing the vehicle battery
Note
Any deviation from the instructions
given in this section may lead to
temporary deactivation or
disturbance of the stop-start system.
When the vehicle battery is being
replaced, please ensure that there
are no open ventilation holes in the
vicinity of the positive terminal. If a
ventilation hole is open in this area, it
must be closed off with a dummy cap,
and the ventilation in the vicinity of the
negative terminal must be opened.
Only use vehicle batteries that allow
the fuse box to be mounted above the
vehicle battery.
Ensure that the battery is always
replaced by the same type of battery.
We recommend that you have the
vehicle battery replaced by a
workshop.
Stop-start system 3 139.
Charging the vehicle battery
9 Warning
On vehicles with stop-start
system, ensure that the charging
potential does not exceed 14.6 V
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
187
when using a battery charger.
Otherwise the vehicle battery may
be damaged.
Jump starting 3 214.
Warning label
Meaning of symbols:
● No sparks, naked flames or
smoking.
● Always shield eyes. Explosive
gases can cause blindness or
injury.
● Keep the vehicle battery out of
reach of children.
● The vehicle battery contains
sulphuric acid which could cause
blindness or serious burn
injuries.
● See the Owner's Instruction for
further information.
● Explosive gas may be present in
the vicinity of the vehicle battery.
Diesel fuel system bleeding
If the tank has been run dry, the diesel
fuel system must be bled. Switch on
the ignition three times for
15 seconds at a time. Then crank the
engine for a maximum of
40 seconds. Repeat this process after
no less than 5 seconds. If the engine
fails to start, seek the assistance of a
workshop.
Wiper blade replacement
Windscreen
Lift the wiper arm, press button to
disengage the wiper blade and
remove.
Attach the wiper blade slightly angled
to the wiper arm and push until it
engages.
Lower wiper arm carefully.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
188
Vehicle care
Rear window
1. Remove the wiper cover from the
wiper assembly.
2. Lift wiper blade.
3. Press slider holder pin.
4. Pull wiper blade out.
Bulb replacement
Switch off the ignition and turn off the
relevant switch or close the doors.
Only hold a new bulb at the base. Do
not touch the bulb glass with bare
hands.
Use only the same bulb type for
replacement.
Replace headlight bulbs from within
the engine compartment.
Note
After driving in heavy rain or after
washing, some exterior light lenses
could appear frosty.
This condition is caused by the
temperature difference between the
inside and outside of the light.
This is similar to the condensation
on your windows inside your vehicle
during the rain and doesn't indicate
a problem with your vehicle.
If the water leaks into the light bulb
circuitry, have the vehicle checked
by your authorised workshop.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
189
Halogen bulbs
9 Warning
Halogen bulbs have pressurized
gas inside and can burst if you
drop or scratch the bulb. You or
others could be injured. Be sure to
read and follow the instructions on
the bulb package.
LED lighting
This vehicle has several LED lights.
For replacement of any LED lighting
assembly, contact a workshop.
Halogen headlights
Baselevel headlight assembly
The base model vehicle has halogen
high beam and low beam headlights,
LED turn lights, a sidelight and
daytime running lights on the
headlight assembly.
Passenger side shown, driver side
similar.
On the driver side remove the
windscreen washer bottle filler neck,
before changing a bulb.
1. High beam headlights
2. Low beam headlights
High beam and low beam headlights
1. Open the bonnet.
2. Remove the protective cover.
3. Turn the bulb anticlockwise and
pull straight back.
4. Disconnect the wiring harness
connector from the bulb.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
190
Vehicle care
5. Install the new bulb in the
headlight assembly by turning
clockwise.
6. Reconnect the wiring harness
connector.
7. Install the protective cover.
For the driver side, reinstall the
windscreen washer bottle filler neck
by firmly pushing it straight into the
bottle. Ensure that the filler neck clip
engages into the underhood electrical
centre retainer.
Uplevel headlight assembly
The uplevel model vehicle has LED
high beam and low beam headlights,
turn lights, a sidelight and daytime
running lights on the headlight
assembly.
Front fog lights
The bulbs are accessible from the
underside of the vehicle
1. Turn the respective wheel inside
to get better access and remove
three torx screws on outside of
wheel house.
Vehicle tools 3 199.
2. Pull and hold lining to get access
to the bulb holder.
3. Pull the retaining rib outwards and
remove plug connector from the
bulb socket.
4. Turn the bulb holder anticlockwise
and remove it from the reflector.
5. Remove and replace the bulb
socket with bulb and attach the
plug connector.
6. Insert the bulb socket into the
reflector by turning clockwise and
engage.
7. Re-assemble the lining and fasten
the three torx screws.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
191
Tail lights
Left-hand side
1. Disengage both covers at the
respective outer side by inserting
a screwdriver. Remove both
covers and unscrew screws.
Remove the panel.
2. First disengage cover by inserting
a screwdriver at the recess. Then
disengage cover at the front and
upper side. Remove cover.
Right-hand side
1. Remove the storage door and the
tyre repair kit.
2. Remove the cover.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
192
Vehicle care
3. Tail / stop light, if not equipped
with LEDs (1)
Turn light (2)
Back-up light (3)
4. Remove bulb holder. Remove
and renew bulb.
5. Insert bulb holder into the tail light
assembly. Install tail light
assembly in body and tighten.
Close covers and engage.
6. Switch on ignition, operate and
check all lights.
Number plate light
1. Prise the light out with a
screwdriver.
2. Remove bulb housing
downwards, taking care not to pull
on the cable.
Rotate bulb holder anticlockwise
to disengage.
3. Remove bulb from holder and
renew bulb.
4. Insert bulb holder in bulb housing
and rotate clockwise.
5. Insert bulb housing and secure
using a screwdriver.
Rear fog light
The bulbs are accessible from the
underside of the vehicle.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
193
1. Turn the bulb holder anticlockwise
and remove it from reflector.
2. Disengage the bulb socket from
the plug connector by pressing
the retaining lug.
3. Remove and replace the bulb
socket with bulb and attach the
plug connector.
4. Insert the bulb socket into the
reflector and turn clockwise to
engage.
Electrical system
Fuses
Data on the replacement fuse must
match the data on the defective fuse.
In a box above the positive terminal of
the battery are some main fuses. If
necessary have them changed by a
workshop.
Before replacing a fuse, turn off the
respective switch and the ignition.
A blown fuse can be recognised by its
melted wire. Do not replace the fuse
until the cause of the fault has been
remedied.
Some functions are protected by
several fuses.
Fuses may also be inserted without
existence of a function.
Note
Not all fuse box descriptions in this
instruction may apply to your vehicle.
When inspecting the fuse box, refer
to the fuse box label.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
194
Vehicle care
Fuse extractor
A fuse extractor may be located in the
fuse box in the engine compartment.
Place the fuse extractor on the
various types of use from the top or
side, and withdraw fuse.
Engine compartment fuse
box
The fuse box is in the engine
compartment.
Disengage the cover, lift it upwards
and remove.
Mini Fuses
No. Circuit
1
Sunroof
2
Exterior mirror switch / Rain
sensor / Power window DRV
3
–
4
–
5
Electrical brake control module
6
Intelligent battery sensor
7
Steering column lock
8
Transmission control module
9
–
10 Rear view camera / Interior rear
view mirror / Headlight switch /
Headlight
11 Rear window wiper
12 Heated rear window
13 Seat, lumbar support
14 Heated exterior mirrors
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
195
No. Circuit
15 LPG module / Fuel system
control module
16 Seat heating
17 Transmission control module R/
C / Water pump / Auxiliary
heater
18 Engine control module R/C
19 Fuel pump
20 –
21 Cooling fan
22 –
23 Ignition coil / Injectors
24 Washer pump
25 Headlamp actuator
26 Engine control sensors
27 –
28 Ignition
29 Ignition 1/2
No. Circuit
30 Exhaust system
31 Left-hand high beam
32 Right-hand high beam
33 Engine control module
34 Horn
35 Air conditioning system
36 Front fog light
J-cases Fuses
No. Circuit
1
Electrical brake control module
2
Front wiper
3
Linear power module
4
Power terminal of instrument
panel fuse box
5
–
6
Fuel heater
7
Starter
No. Circuit
8
Cooling fan
9
Cooling fan
10 Engine control module / Glow
plug
11 Starter
Instrument panel fuse box
In left-hand drive vehicles, the interior
fuse box is located on the underside
of the driver's side instrument panel.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
196
Vehicle care
To access the fuses, remove the
storage. To remove the storage, open
and pull it.
In right-hand drive vehicles, the
interior fuse box is located behind a
cover in the glovebox on the
passenger side. To access the fuses,
open the glovebox, then open the
cover, fold it down and pull it.
Mini Fuses
No. Circuit
1
Body control module
2
Body control module
3
Body control module
4
Body control module
5
Body control module
6
Body control module
7
Body control module
8
Body control module
9
Ignition switch
10 Safety diagnosis module
11 Data link connector
12 Climate control
13 Tailgate
14 Central gateway module
15 Lane departure warning / Inte‐
rior mirror
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
197
No. Circuit
16 Adaptive forward lighting
17 Column lock
18 Ultrasonic park assist module
19 Body control module / Regu‐
lated voltage control
20 Steering wheel
21 –
22 Cigarette lighter / DC accessory
power outlet (front)
23 Cigarette lighter / DC accessory
power outlet (rear center
console)
24 Spare
25 Telematics service module
26 Heated steering wheel
27 Instrument panel cluster / Info‐
tainment system / Auxiliary
heater switch
28 Trailer socket
No. Circuit
29 Info Display / Infotainment
system
30 Transmission control module
31 Instrument panel cluster
32 Infotainment system
33 Trailer socket
34 Passive entry / Passive start
module
S/B Fuses
No. Circuit
01
Power seat switch
02
Spare
03
Power windows front
04
Power windows rear
05
Logistic mode
06
Power seat switch
No. Circuit
07
Spare
08
Spare
Midi Fuse
No.
Circuit
M01
PTC
Load compartment fuse box
Located in the left side of rear
compartment.
To access the fuses, remove the
cover.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст