Opel Mokka X (2019 year). Instruction — part 8
118
Lighting
Pull lever to deactivate high beam.
High beam assist 3 120.
High beam assist
This feature automatically activates
the high beam at night when vehicle
speed is faster than40 km/h.
It switches automatically back to low
beam when:
● The camera or a sensor in the
windscreen detects the lights of
oncoming or preceding vehicles.
● The vehicle speed drops below
20 km/h.
● It is foggy or snowy.
● Driving in urban areas.
If there are no restrictions detected,
the system switches back to high
beam.
Activation
The high beam assist is activated by
pushing the indicator lever twice. The
high beam is switched on
automatically at a speed above
40 km/h.
The green control indicator f
illuminates continuously when the
assist is activated, the blue one 7
illuminates when high beam is on.
Control indicator f 3 96.
Deactivation
Push indicator lever once. It is also
deactivated when front fog lights are
switched on.
If a headlight flash is activated when
the high beam is on, the high beam
assist will be deactivated.
If a headlight flash is activated when
the high beam is off, the high beam
assist will remain activated.
The latest setting of the high beam
assist will remain after the ignition is
switched on again.
Headlight flash
Pull lever to activate the headlight
flash.
Pulling lever deactivates high beam.
AFL-LED headlights 3 120.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
119
Headlight range adjustment
Instruction headlight range
adjustment
To adapt headlight range to the
vehicle load to prevent dazzling: turn
thumb wheel ? to required position.
0 : front seats occupied
1 : all seats occupied
2 : all seats occupied and load
compartment laden
3 : driver's seat occupied and load
compartment laden
Dynamic automatic headlight
Headlights when driving
abroad
The asymmetrical headlight beam
extends visibility at the edge of the
road at the passenger side.
However, when driving in countries
where traffic drives on the opposite
side of the road, adjust the headlights
to prevent dazzling of oncoming
traffic.
Vehicles with halogen headlight
system
The adjusting screws are located
above the headlight.
Turn the adjusting screws with the
screwdriver clockwise by half a turn.
To reset to left-hand traffic mode, turn
adjuster elements on both headlight
housings anticlockwise by half a turn.
Caution
Have the adjustment of the
headlights checked after
deactivation.
We recommend consulting a
workshop.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
120
Lighting
Vehicles with adaptive forward
lighting system
1. Key in ignition switch.
2. Pull turn signal lever and hold
(headlight flash).
3. Switch on ignition.
4. After approx. five seconds the
control indicator f starts flashing
and an acoustic signal sounds.
On another version the headlights are
adjusted for driving on the opposite
side of the road via the vehicle
personalisation menu. Select the
relevant setting in Settings, I Vehicle.
Vehicle personalisation 3 106.
Every time the ignition is switched on,
control indicator f flashes as a
reminder for approx. four seconds.
For deactivation, operate the same
procedure as described above.
Control indicator f will not flash when
function is deactivated.
Control indicator f 3 96.
Daytime running lights
Daytime running lights increase
visibility of the vehicle during daylight.
They are switched on automatically
during daytime when engine is
running.
The system switches between
daytime running lights and headlights
automatically, depending on the
lighting conditions.
Automatic light control 3 117.
Adaptive forward lighting
The Adaptive forward lighting
functions are only available with LED
headlights for low and high beam.
Light range, light distribution and
intensity of light are variably triggered
depending on the lighting conditions,
road type and driving situation.
LED headlights for low and high
beam
LED headlights for low and high beam
ensure better visibility under all
conditions.
Operation is the same as for halogen
headlights.
Light switch 3 116.
High beam 3 117.
Headlight flash 3 118.
Headlights when driving abroad
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
121
AFL-LED lighting functions
AFL-LED lighting functions are active
automatically with light switch in
position AUTO. AFL-LED includes
following functions:
● curve and cornering lights
● town light
● country light
● motorway light
● high beam assist
● reverse parking function
● eco mode
● dynamic automatic headlight
levelling
Curve and cornering lights
On tight bends or when turning off,
depending on the steering angle or
the indicator light signal, an additional
left or right reflector is switched on
which illuminates the road in the
direction of travel. It is activated up to
a speed of 70 km/h.
Town light
Activated automatically at a speed up
to approx. 55 km/h. In situations with
exterior ambient light both cornering
lights are switched on with reduced
intensity. The light is wide and
symmetrical.
Country light
Activated automatically at a speed of
approx. 55 km/h. The beam of light
and the brightness is different
between the left and the right side.
High beam assist
This feature allows high beam to
function as the main driving light at
night and when vehicle speed
exceeds 40 km/h.
It switches automatically to low beam
when:
● The camera or a sensor in the
windscreen detects the lights of
oncoming or preceding vehicles.
● The vehicle speed drops below
20 km/h.
● It is foggy or snowy.
● Driving in urban areas.
If there are no restrictions detected,
the system switches back to high
beam.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
122
Lighting
Activation
The high beam assist is activated by
pushing the indicator lever twice. The
high beam is switched on
automatically at a speed above
40 km/h.
The green control indicator f
illuminates continuously when the
assist is activated, the blue one 7
illuminates when high beam is on.
Control indicator f 3 96.
Deactivation
Push indicator lever once. It is also
deactivated when front fog lights are
switched on.
If a headlight flash is activated when
the high beam is on, the high beam
assist will be deactivated.
If a headlight flash is activated when
the high beam is off, the high beam
assist will remain activated.
The latest setting of the high beam
assist will remain after the ignition is
switched on again.
Reverse parking function
To assist driver's orientation when
parking, both corner lights and
reversing light illuminate when
headlights are on and reverse gear is
engaged. They remain illuminated for
a short time after disengaging reverse
gear or until driving faster than
7 km/h in a forward gear.
Eco mode
If the vehicle stops, e. g. due to traffic
lights, an energy saving mode for
headlights is activated.
Dynamic automatic headlight
levelling
To prevent oncoming traffic from
being dazzled, headlight levelling is
automatically adjusted based on
vehicle inclination information.
Fault in AFL-LED lighting system
When the system detects a failure in
the LED headlight system, f
illuminates and a warning is displayed
in the Driver Information Centre.
Hazard warning flashers
Operated by pressing ¨.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
123
Turn lights
lever up
: right turn signal
lever down : left turn signal
A resistance point can be felt when
moving the lever.
Constant flashing is activated when
the lever is being moved beyond the
resistance point. It is deactivated
when the steering wheel is moved in
the opposite direction or lever is
instructionly moved back to its neutral
position.
Activate temporary flashing by
holding the lever just before the
resistance point. Turning lights will
flash until lever is being released.
To activate three flashes, tap the
lever briefly without passing the
resistance point.
With a trailer connected, turn signal
flashes six times and tone frequency
changes when pressing the lever until
resistance is felt and then releasing.
Move the lever to the resistance point
and hold for flashing until lever is
released.
Front fog lights
Operated by pressing >.
Rear fog light
Operated by pressing ø.
Light switch in position AUTO:
switching on rear fog light will switch
headlights on automatically.
Light switch in position 8: rear fog
light can only be switched on with
front fog lights.
Reversing lights
The reversing light comes on when
the ignition is on and reverse gear is
selected.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
124
Lighting
Misted light covers
The inside of the light housing may
mist up briefly in poor, wet and cold
weather conditions, in heavy rain or
after washing. The mist disappears
quickly by itself. To help, switch on the
headlights.
Interior lighting
Instrument panel
illumination control
Brightness of the following lights can
be adjusted when the exterior lights
are on:
● instrument panel illumination
● steering wheel controls
Turn thumb wheel A and hold until
the desired brightness is obtained.
Interior lights
Courtesy light
Front
press v : off
w
: automatic switching on
and off
press u : on
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
125
Rear
⃒ : on
w
: automatic switching on and off
§
: off
Reading lights
The front reading lights are located in
the overhead console.
Press s and t to turn each light on
or off.
Glove box lighting
Illuminates when the glovebox is
opened.
Sunvisor lights
Illuminates when the cover is opened.
Lighting features
Entry lighting
Welcome lighting
Following lights are switched on for a
short time by unlocking the vehicle
with the radio remote control:
● low beam
● sidelights
● tail lights
● number plate lights
● instrument panel light
● interior lights
This function works only in the dark
and facilitates locating the vehicle.
Activation or deactivation of this
function can be changed in the
vehicle settings.
Vehicle personalisation 3 106.
The following lights will additionally
switch on when driver's door is
opened:
● illumination of some switches
● some interior lights
-------------------------------------------------------------------------------------------------------------------------------------------------------------
126
Lighting
Exit lighting
Low beam, sidelights and tail lights
illuminate the surrounding area for an
adjustable time after leaving the
vehicle.
Switching on
Activation, deactivation and duration
of lighting of this function can be
changed in the vehicle settings.
Vehicle personalisation 3 106.
1. Switch off ignition.
2. Remove ignition key.
3. Open driver's door.
4. Pull turn signal lever.
5. Close driver's door.
If the driver's door is not closed the
lights switch off after a few seconds.
The lighting is switched off
immediately if the turn signal lever is
pulled while the driver's door is open.
Battery discharge protection
To prevent discharge of the battery
when the ignition is switched off,
some interior lights are switched off
automatically after some time.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
127
Climate control
Climate control systems . . . . 127
Heating and ventilation system 127
Air conditioning system . . ... 128
Electronic climate control
system . . . . . . . . . 129
Auxiliary heater . . . . . . 131
Air vents . . . . . . . . . . 131
Adjustable air vents . . . . . 131
Fixed air vents . . . . . . . 132
Maintenance . . . . . . . .. 132
Air intake . . . . . . . . . 132
Air conditioning regular
operation . . . . . . . . 132
Service . . . . . . . . . 132
Climate control systems
Heating and ventilation
system
Controls for:
● air distribution
● temperature
● fan speed
● demisting and defrosting
Heated rear window Ü 3 37.
Temperature
red : warm
blue : cold
Heating will not be fully effective until
the engine has reached normal
operating temperature.
Air distribution
l
: to windscreen and front door
windows
M
: to head area
K
: to foot well and windscreen
Combination settings are possible.
Fan speed
Adjust the air flow by switching the fan
to the desired speed.
Demisting and defrosting
● Press V: fan automatically
switches to higher speed, the air
distribution is directed towards
the windscreen.
● Set temperature control to
warmest level.
● Switch on heated rear window Ü.
● Open side air vents as required
and direct them towards the door
windows.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
128
Climate control
Air conditioning system
In addition to the heating and
ventilation system, the air
conditioning system has controls for:
n
: cooling
4
: air recirculation
Cooling n
Press n to switch on cooling. The
LED in the button illuminates to
indicate activation. Cooling is only
functional when the engine is running
and climate control fan is switched on.
Press n again to switch off cooling.
The air conditioning system cools and
dehumidifies (dries) as soon as the
outside temperature is above a
specific level. Therefore
condensation may form and drip from
under the vehicle.
If no cooling or drying is required,
switch off the cooling system for fuel
saving reasons. Activated cooling
may inhibit Autostops.
Stop-start system 3 139.
Air recirculation system 4
Press 4 to activate air recirculation
mode. The LED in the button
illuminates to indicate activation.
Press 4 again to deactivate air
recirculation mode.
9 Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling the air
humidity increases, so the
windows may mist up from inside.
The quality of the passenger
compartment air deteriorates,
which may cause the vehicle
occupants to feel drowsy.
In warm and very humid ambient air
conditions, the windscreen may mist
up from outside when cold air is
directed towards it. If windscreen
mists up from outside, activate
windscreen wiper and deactivate l.
Maximum cooling
Briefly open the windows so that hot
air can disperse quickly.
● Switch on cooling n.
● Air recirculation system 4 on.
● Press air distribution switch M.
● Set temperature control to
coldest level.
● Set fan speed to highest level.
● Open all vents.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
129
Demisting and defrosting the
windows V
● Press V: fan automatically
switches to higher speed, the air
distribution is directed towards
the windscreen.
● Set temperature control to
warmest level.
● Switch on heated rear window Ü.
● Open side air vents as required
and direct them towards the door
windows.
Note
If V is pressed while the engine is
running, an Autostop will be inhibited
until V is pressed again.
If l is pressed with the fan switched
on and the engine running, an
Autostop will be inhibited until l is
pressed again or until the fan is
switched off.
If V is pressed while the engine is
in an Autostop, the engine will restart
automatically.
If l is pressed with the fan switched
on while the engine is in an
Autostop, the engine will restart
automatically.
Electronic climate control
system
Controls for:
● air distribution
● temperature
● fan speed
AUTO : automatic mode
4
: instruction air recirculation
V
: demisting and defrosting
Heated rear window Ü 3 37.
The preselected temperature is
automatically regulated. In automatic
mode, the fan speed and air
distribution automatically regulate the
air flow.
The system can be instructionly adapted
via the use of air distribution and air
flow controls.
Each change of settings is shown in
the Info Display for a few seconds.
The electronic climate control system
is only fully operational when the
engine is running.
Automatic mode AUTO
Basic setting for maximum comfort:
● Press AUTO: the air distribution
and fan speed are regulated
automatically.
● Open all air vents.
● Press n to switch on cooling.
● Set the desired temperature.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
130
Climate control
Temperature preselection
Temperatures can be set to the
desired value.
If the minimum temperature is set, the
climate control system runs at
maximum cooling.
If the maximum temperature is set,
the climate control system runs at
maximum heating.
Note
If the temperature is to be reduced
for climate comfort reasons, an
Autostop may be inhibited or the
engine will restart automatically
when cooling is switched on.
Stop-start system 3 139.
The temperature can be adjusted
separately for driver and front
passenger side.
Demisting and defrosting the
windows V
● Press V.
● Temperature and air distribution
are set automatically and the fan
runs at high speed.
● Switch on heated rear window Ü.
● To return to previous mode:
press V, to return to automatic
mode: press AUTO.
Note
If V is pressed while the engine is
running, an Autostop will be inhibited
until V is pressed again.
If l is pressed with the fan switched
on and the engine running, an
Autostop will be inhibited until l is
pressed again or until the fan is
switched off.
If V is pressed while the engine is
in an Autostop, the engine will restart
automatically.
If l is pressed with the fan switched
on while the engine is in an
Autostop, the engine will restart
automatically.
Instruction settings
Climate control system settings can
be changed by activating the buttons
and rotary knobs as follows.
Changing a setting will deactivate the
automatic mode.
Fan speed Z
The selected fan speed is indicated
with x and a number in the display. If
the fan is switched off, the air
conditioning is also deactivated.
To return to automatic mode: Press
AUTO.
Air distribution l, M, K
Press appropriate button for desired
adjustment. The LED in the button
illuminates to indicate activation.
l
: to windscreen and front door
windows (air conditioning is
activated in the background to
help prevent windows from
fogging)
M
: to head area
K
: to foot well and windscreen
Combination of settings are possible.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
131
Return to automatic air distribution:
Deactivate corresponding setting or
press AUTO.
Cooling n
Press n to switch on cooling. The
LED in the button illuminates to
indicate activation. Cooling is only
functional when the engine is running
and climate control fan is switched on.
Press n again to switch off cooling.
The air conditioning system cools and
dehumidifies (dries) when outside
temperature is above a specific level.
Therefore condensation may form
and drip from under the vehicle.
If no cooling or drying is required,
switch off the cooling system for fuel
saving reasons. Activated cooling
may inhibit an Autostop.
Stop-start system 3 139.
Eco appears in the display when
cooling is deactivated.
Air recirculation mode 4
Press 4 once to activate the
manual air recirculation mode.
9
Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling the air
humidity increases, so the
windows may mist up from inside.
The quality of the passenger
compartment air deteriorates,
which may cause the vehicle
occupants to feel drowsy.
Air conditioning with the engine
not running
When ignition is off, the residual heat
or cooling in the system can be used
for climate control in passenger
compartment.
Auxiliary heater
Air heater
Quickheat is an electric auxiliary air
heater which automatically warms up
the passenger compartment more
quickly.
Air vents
Adjustable air vents
At least one air vent must be open
while the cooling is on.
To open the vent, turn the adjuster
wheel to the right. Adjust the air
amount at the vent outlet by turning
the adjuster wheel.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
132
Climate control
Direct the flow of air by tilting and
swivelling the slats.
To close the vent, turn the adjuster
wheel to the left.
9 Warning
Do not attach any objects to the
slats of the air vents. Risk of
damage and injury in case of an
accident.
Fixed air vents
Additional air vents are located
beneath the windscreen and door
windows and in the foot wells.
Maintenance
Air intake
The air intake in front of the
windscreen in the engine
compartment must be kept clear to
allow air intake.
Remove any leaves, dirt or snow.
Air conditioning regular
operation
In order to ensure continuously
efficient performance, cooling must
be operated for a few minutes once a
month, irrespective of the weather
and time of year. Operation with
cooling is not possible when the
outside temperature is too low.
Service
For optimal cooling performance, it is
recommended to annually check the
climate control system, starting
three years after initial vehicle
registration, including:
● functionality and pressure test
● heating functionality
● leakage check
● check of drive belts
● cleaning of condenser and
evaporator drainage
● performance check
Note
Refrigerant R-134a contains
fluorinated greenhouse gases.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Driving and operating
133
Driving and
operating
Driving hints . . . . . . . ... 134
Control of the vehicle . . . ... 134
Steering . . . . . . . . ... 134
Starting and operating . . . ... 134
New vehicle running-in . . . 134
Ignition switch positions . . ... 135
Power button . . . . . . ... 136
Retained power off . . . . .. 137
Starting the engine . . . . .. 137
Overrun cut-off . . . . . . 139
Stop-start system . . . . . 139
Parking . . . . . . . . . 141
Engine exhaust . . . . . . .. 142
Exhaust filter . . . . . . . 142
Catalytic converter . . . . ... 143
AdBlue . . . . . . . . . . 144
Automatic transmission . . . .. 146
Transmission display . . . ... 146
Selector lever . . . . . . .. 147
Manual mode . . . . . . ... 148
Electronic driving programmes 148
Fault . . . . . . . . . . 148
Interruption of power supply . 149
Manual transmission . . . . .. 149
Drive systems . . . . . . . 150
All-wheel drive . . . . . . . 150
Brakes . . . . . . . . . . 151
Antilock brake system . . . . 151
Parking brake . . . . . . .. 151
Brake assist . . . . . . . . 152
Hill start assist . . . . . . . 152
Ride control systems . . . . . 152
Traction Control system . . .. 152
Electronic Stability Control . .. 153
Descent control system . . ... 154
Driver assistance systems . . . 155
Cruise control . . . . . . .. 155
Speed limiter . . . . . . ... 157
Forward collision alert . . . . 158
Following distance indication ... 160
Parking assist . . . . . . .. 161
Rear view camera . . . . ... 163
Traffic sign assistant . . . . 165
Lane departure warning . . .. 168
Fuel . . . . . . . . . . . 169
Fuel for petrol engines . . . . 169
Fuel for diesel engines . . . 171
Fuel for liquid gas operation . 171
Refuelling . . . . . . . . 172
Trailer hitch . . . . . . . . 176
General information . . . . . 176
Driving characteristics and
towing tips . . . . . . . .. 176
Trailer towing . . . . . . ... 177
Towing equipment . . . . ... 177
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст