Opel Vivaro (2018 year). Instruction — part 7
Instruments and controls
103
steering column controls, the voice
recognition system (if available) or via
the touchscreen display.
Touchscreen operation
Make the appropriate selection from
the available menus and options by
touching the display screen with the
finger.
For further information, refer to the
Infotainment instruction.
Vehicle messages
Messages are displayed in the Driver
Information Centre and may be
accompanied by illumination of
control indicator F or C in the
instrument cluster.
Information messages
Information messages regarding, e.g.
engine starting conditions, stop-start
system, parking brake application,
central locking, steering wheel lock
etc. provide the current status of
certain vehicle functions and
instructions for use.
Fault messages
Fault messages regarding, e.g. fuel
filter, airbags, exhaust emissions etc.
are displayed together with control
indicator F. Drive with caution and
seek the assistance of a workshop as
soon as possible.
To remove fault messages, e.g.
"CHECK INJECTION", from the
display, press button on end of wiper
lever. After a few seconds the
message may disappear
automatically and F remains
illuminated. The fault will then be
stored in the on board system.
Warning messages
Warning messages regarding, e.g.
engine, battery or brake system
failure, are displayed together with
control indicator C and may be
accompanied by a warning chime.
Stop engine immediately and seek
the assistance of a workshop.
Warning messages, e.g. "BATTERY
CHARGING FAULT" disappear from
the display automatically when the
cause of the fault has been remedied.
Fuel economy messages
Fuel economy messages provide tips
to improve fuel efficiency. Journeys
can be saved in the system memory,
enabling you to compare
performances.
Refer to Infotainment instruction for
further information.
Fuel economy rating 3 105.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
104
Instruments and controls
Warning chimes
Only one warning chime will sound at
a time.
A corresponding message may also
appear in the Driver Information
Centre when a warning chime is
sounded.
When starting the engine or whilst
driving:
● If seat belt is not fastened 3 55.
● If the parking assist detects an
● If the vehicle speed briefly
● If a door or the bonnet is not
properly closed when vehicle
exceeds a certain speed.
● During activation and
deactivation of alarm monitoring
of vehicle inclination 3 38.
● If there is a fault in the brake
system 3 98.
● If the vehicle battery is not
charging 3 98.
● If engine lubrication is interrupted
● If AdBlue needs to be refilled or a
fault is present 3 141.
● If the electronic key is outside of
the detection range.
Electronic key system 3 24.
Power button 3 132.
When the vehicle is parked and /
or the driver's door is opened:
● If the key has been left in the
ignition.
● If the electronic key has been left
in the card reader.
Electronic key system 3 24.
Power button 3 132.
● If the vehicle is in an Autostop.
Stop-start system 3 136.
● If the exterior lights are on
108.
Engine oil level
If the minimum engine oil level is
reached, a message is displayed in
the Driver Information Centre 3 102
for 30 seconds after the engine is
started.
Check oil level 3 167.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
105
Trip computer
The trip computer provides
information on driving data, which is
continually recorded and evaluated
electronically.
Depending on vehicle, the following
functions can be selected by pressing
button repeatedly on end of wiper
lever:
● fuel used
● average consumption
● instantaneous consumption
● range
● distance travelled
● average speed
● AdBlue percentage remaining
● distance before service 3 93
● clock 3 88
● outside temperature 3 87
● cruise control and speed limiter
stored speed 3 152
● fuel economy rating (ecoScoring)
● fault and information messages
● odometer 3 91
● trip odometer 3 91
Fuel used
Displays the amount of fuel
consumed since the last reset.
The measurement can be restarted at
any time by pressing and holding the
button.
Average consumption
The value is displayed after driving a
distance of 400 metres.
Average consumption is displayed,
taking into consideration the distance
travelled and the fuel used since the
last reset.
The measurement can be restarted at
any time.
Instantaneous consumption
The value is displayed after reaching
a speed of 30 km/h.
Range
The value is displayed after driving a
distance of 400 metres.
The range is calculated from the
current contents of the fuel tank and
the average consumption since the
last reset.
The range will not display if control
indicator Y is illuminated in the
instrument cluster 3 101.
Distance travelled
Displays the distance driven since the
last reset.
The measurement can be restarted at
any time.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
106
Instruments and controls
Average speed
The value is displayed after driving a
distance of 400 metres.
The average speed since the last
reset is displayed.
The measurement can be restarted at
any time.
Interruptions in the journey with the
ignition off are not included in the
calculations.
Reset trip computer information
To reset the trip computer, select one
of its functions then press and hold
the button on the end of the wiper
lever.
The following trip computer
information can be reset:
● fuel used
● average consumption
● distance travelled
● average speed
The trip computer will reset
automatically when the maximum
value of any of the parameters is
exceeded.
Fuel economy rating (ecoScoring)
If equipped, a rating of 0 to 100 is
shown in the Info-Display to help
evaluate fuel efficiency, based on
your driving style.
Higher ratings indicate better fuel
economy.
Tips to improve fuel economy are also
given in the Info-Display. Journeys
can be saved in the system memory,
enabling you to compare
performances. Refer to Infotainment
instruction for further information.
Vehicle messages 3 103.
Journey record
When the engine is switched off, a
record of the last journey may be
shown in the Info-Display.
The following information is
displayed:
● average fuel consumption
● total fuel consumption
● trip odometer
● fuel saved in km
Unit of measurement
To change the unit of measurement
for the duration of a journey:
Vehicles with power button:
With ignition off, simultaneously press
and hold button on end of wiper lever
and press the power button 3 132;
the central display flashes for approx.
ten seconds until the new unit is
displayed. Release button on end of
wiper lever when the display stops
flashing.
Vehicles without power button:
With ignition off, simultaneously press
and hold button on end of wiper lever
and switch on the ignition; the central
display flashes for approx.
ten seconds until the new unit is
displayed. Release button on end of
wiper lever when the display stops
flashing.
When the engine is switched off, the
trip computer automatically returns to
the original unit of measurement.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
107
Interruption of power supply
If the power supply has been
interrupted or if the vehicle battery
voltage has dropped too low, the
values stored in the trip computer will
be lost.
Tachograph
The tachograph is operated as
described in the operating
instructions supplied. Observe
regulations regarding use.
Depending on equipment, the
tachograph may be fitted in a console
located above the Infotainment
system in the instrument panel.
Note
When a tachograph is fitted, the total
distance travelled may be shown
only on the tachograph and not in the
odometer within the instrument
display.
Odometer 3 91.
Control indicator & 3 102 illuminates
in the instrument cluster in the event
of a fault. Seek the assistance of a
workshop.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
108
Lighting
Lighting
Exterior lighting . . . . . . .. 108
Light switch . . . . . . . .. 108
Automatic light control . . . . 109
High beam . . . . . . . ... 109
Headlight flash . . . . . . . 109
Headlight range adjustment . 109
Headlights when driving
abroad . . . . . . . . . 110
Daytime running lights . . . . 110
Adaptive forward lighting . . . 110
Hazard warning flashers . . .. 111
Turn and lane-change signals . 111
Front fog lights . . . . . . . 111
Rear fog lights . . . . . . . 112
Reversing lights . . . . . ... 112
Misted light covers . . . . ... 112
Interior lighting . . . . . . ... 112
Instrument panel illumination
control . . . . . . . . . . 112
Interior lights . . . . . . . 112
Load compartment lighting . .. 114
Reading lights . . . . . . .. 114
Glove box lighting . . . . . 114
Lighting features . . . . . . 114
Entry lighting . . . . . . . 114
Exit lighting . . . . . . . .. 114
Battery discharge protection . 115
Exterior lighting
Light switch
Turn outer switch:
7
: off
8
: sidelights
9P
: headlights
High beam control indicator P
Low beam control indicator 9 3 101.
Note
If the headlights have been switched
on instructionly, a warning chime will
sound when the engine is switched
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
109
off and when the driver's door is
opened as a reminder that the lights
are still on.
Tail lights
Tail lights are illuminated together
with low beam and sidelights.
Automatic light control
AUTO : automatic light control
When the automatic light control
function is activated and the engine is
running, the system switches
between daytime running lights and
headlights depending on the external
lighting conditions.
For reasons of safety, it is advisable
to have the automatic light control
function activated.
Automatic headlight activation
During poor lighting conditions the
headlights are switched on.
Additionally, headlights are switched
on if the windscreen wipers have
been activated for several wipes.
Daytime running lights 3 110.
High beam
To switch from low to high beam,
push lever.
To switch back to low beam, push
lever again or pull.
Headlight flash
To activate the headlight flash, pull
lever.
Headlight range adjustment
Instruction headlight range
adjustment
Adapt headlight range to the vehicle
load to prevent dazzling of oncoming
traffic.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
110
Lighting
Turn thumb wheel ? to required
position:
0 : No load
4 : Loaded up to permissible
maximum weight
Headlights when driving
abroad
The asymmetrical headlight beam
extends visibility at the edge of the
road at the passenger side.
However, when driving in countries
where traffic drives on the opposite
side of the road, adjust the headlights
to prevent dazzling of oncoming
traffic.
Adjustment
Open the bonnet 3 166 and identify
the marking (shown in the illustration)
beside each of the headlights.
For each headlight:
Using a screwdriver, turn the screw
by a
1
/
4
turn towards the ] symbol to
lower the beams or towards the <
symbol to raise the beams.
Ensure the headlight beams are
returned to their original positions
when required.
Daytime running lights
Daytime running lights increase
visibility of the vehicle during daylight.
They may be switched on
automatically when the engine is
running.
If required, the daytime running lights
can be deactivated via the
Infotainment system. For further
information, refer to Infotainment
instruction.
Automatic light control 3 109.
Adaptive forward lighting
Cornering light
With the low beam switched on,
depending on the steering angle,
vehicle speed and gear selected
when cornering, the front fog light will
also switch on, to illuminate the
corner of the road on the respective
side.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
111
Hazard warning flashers
Operated by pressing ¨.
In the event of hard braking, the
hazard warning flashers may turn on
automatically. Switch off by pressing
¨
.
Turn and lane-change
signals
lever up
: right turn signal
lever down : left turn signal
A resistance point can be felt when
moving the lever.
Constant flashing is activated when
the lever is moved beyond the
resistance point. It is deactivated
when the steering wheel is moved in
the opposite direction or lever is
instructionly moved back to its neutral
position.
Activate temporary flashing by
holding the lever just before the
resistance point. Turn signal lights will
flash until lever is released.
To activate three flashes, tap the
lever briefly without passing the
resistance point.
Front fog lights
Turn inner switch to position >;
control indicator > illuminates in the
instrument cluster.
Front fog lights will only operate when
the ignition and headlights are
switched on.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
112
Lighting
Rear fog lights
Turn inner switch to position ø;
control indicator ø illuminates in the
instrument cluster.
Rear fog light comes on together with
front fog lights and will only operate
when the ignition and headlights are
switched on.
Reversing lights
The reversing lights come on when
the ignition is on and reverse gear is
selected.
Misted light covers
The inside of the light covers may mist
up briefly in poor, wet and cold
weather conditions, in heavy rain or
after washing. The mist disappears
quickly by itself; to help, switch on the
headlights.
Interior lighting
Instrument panel
illumination control
Brightness of the following lights can
be adjusted when the exterior lights
are on:
● instrument panel illumination
● info-display
● illuminated switches and
operation elements.
Turn thumb wheel b until the desired
brightness is obtained.
Interior lights
Courtesy lights
During entry and exit of the vehicle,
depending on switch position the front
and rear courtesy lights automatically
switch on, together with the foot well
lights, then switch off after a delay.
Front courtesy lights
Operate rocker switch:
press 7
: off
centre posi‐
tion
: automatic switching
on and off
press d
: on
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
113
With the rocker switch in its central
position, the light functions as a
courtesy light and illuminates when
the front doors are opened.
When the front doors are closed, the
courtesy light extinguishes after a
delay.
Rear courtesy lights
The upper load compartment lights
can be set to illuminate when the side
or rear doors are opened, or switched
on constantly.
Operate rocker switch:
press 7
: off
centre posi‐
tion
: automatic switching
on and off
press d
: on
With the rocker switch in its central
position, the light functions as a
courtesy light and illuminates when
the side or rear doors are opened.
When the doors are closed, the
courtesy light extinguishes after a
delay.
LED spotlights
Depending on vehicle, adjustable
LED spotlights, also including rocker
switch, may be present.
Bench seat lights
Depending on vehicle, bench seat
light illuminates when the sliding side
door is opened.
Rear seats lights
Depending on vehicle, rear seats
lights may be available.
The lights ar operated by pressing the
switch of the respective light.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
114
Lighting
Load compartment lighting
The lower load compartment lights
come on when the load compartment
is opened.
Reading lights
Front reading light
Operate rocker switch:
press 7 : off
press l : on
Glove box lighting
The glovebox light comes on when
the glovebox is opened.
Lighting features
Entry lighting
Welcome lighting
Vehicle lights are switched on for a
short time to facilitate locating the
vehicle when it is dark.
Remote control operation
Lights switch on when unlocking the
vehicle with the remote control.
Electronic key system operation
Press t. Press again to switch off.
Exit lighting
If equipped, headlights come on for
approx. 30 seconds after the vehicle
is parked and the system is activated.
Activating
1. Switch off lights (position 7).
2. Switch off ignition.
3. Remove ignition key.
4. Open driver's door.
5. Pull turn signal lever towards
steering wheel.
A corresponding message may
appear in the Driver Information
Centre 3 102.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
115
This action can be repeated up to four
times to a maximum period of
two minutes.
The lighting is turned off immediately
by switching on the ignition or turning
the light switch.
Battery discharge protection
To prevent discharge of the vehicle
battery when the ignition is switched
off, some interior lights may be
switched off automatically after some
time.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
116
Climate control
Climate control
Climate control systems . . . . 116
Heating and ventilation system 116
Air conditioning system . . ... 117
Electronic climate control
system . . . . . . . . . 118
Rear heating system . . . ... 120
Rear air conditioning system ... 121
Auxiliary heater . . . . . . 122
Air vents . . . . . . . . . . 127
Adjustable air vents . . . . . 127
Fixed air vents . . . . . . . 128
Glovebox cooler . . . . . .. 128
Maintenance . . . . . . . .. 128
Air intake . . . . . . . . . 128
Pollen filter . . . . . . . ... 128
Air conditioning regular
operation . . . . . . . . 128
Service . . . . . . . . . 129
Climate control systems
Heating and ventilation
system
Controls for:
● temperature
● fan speed
● air distribution
Heated rear window Ü 3 45.
Temperature
red : warm
blue : cold
Heating will not be fully effective until
the engine has reached normal
operating temperature.
Fan speed
Adjust the air flow by switching the fan
to the desired speed.
Air distribution
M
: to head area
L
: to head area and foot well
K
: to foot well
J
: to windscreen, front door
windows and foot well
V
: to windscreen and front door
windows
Intermediate settings are possible.
Demisting and defrosting the
windows
● Set temperature control to
warmest level.
● Set fan speed to highest level.
● Set air distribution control to V.
● Switch on heated rear window Ü.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
117
● Open side air vents as required
and direct them towards door
windows.
● For simultaneous warming of the
foot well, set air distribution
control to J.
Heated rear window 3 45.
Air conditioning system
In addition to the heating and
ventilation system, the air
conditioning system has controls for:
A/C : cooling
4
: air recirculation
Cooling (A/C)
Press A/C to switch on cooling.
Activation is indicated by illumination
of the LED in the button. Cooling is
only functional when the engine is
running and climate control fan is
switched on.
Press A/C again to switch off cooling.
The air conditioning system cools and
dehumidifies (dries) the air when
outside temperature is above a
specific level. Therefore
condensation may form and drip from
under the vehicle.
If no cooling or drying is required,
switch off the cooling system for fuel
saving reasons. Activated cooling
may inhibit an Autostop.
Stop-start system 3 136.
Note
Air conditioning performance is
reduced when ECO mode has been
Air recirculation system 4
Press 4 to activate air recirculation
mode. Activation is indicated by
illumination of the LED in the button.
Press 4 again to deactivate air
recirculation mode.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
118
Climate control
9 Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling, the
air humidity increases, so the
windows may mist up from inside.
The quality of the passenger
compartment air deteriorates,
which may cause the vehicle
occupants to feel drowsy.
In warm and very humid ambient air
conditions, the windscreen might mist
up from outside when cold air is
directed towards it. If windscreen
mists up from outside, activate
windscreen wiper and avoid the use
of air distribution settings J and V.
Maximum cooling
Briefly open the windows so that hot
air can disperse quickly.
● Cooling A/C on.
● Air recirculation system 4 on.
● Set air distribution control to M.
● Set temperature control to
coldest level.
● Set fan speed to highest level.
● Open all air vents.
Demisting and defrosting the
windows
● Set temperature control to
warmest level.
● Set fan speed to highest level.
● Set air distribution control to V.
● Switch cooling A/C on.
● Switch on heated rear window Ü.
● Open side air vents as required
and direct them towards door
windows.
● For simultaneous warming of the
foot well, set air distribution
control to J.
Electronic climate control
system
Controls for:
● air distribution
● temperature
● fan speed
AUTO
: automatic mode
Ê
: demisting and defrosting
Ü
: heated rear window
A/C OFF : switch off air conditioning
u
: manual air recirculation
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст