Opel Vivaro (2018 year). Instruction — part 8
Climate control
119
The preselected temperature is
automatically regulated. In Automatic
mode, the fan speed and air
distribution automatically regulate the
air flow.
The system can be instructionly adapted
via the use of air distribution and air
flow controls.
Electronic climate control system is
only fully operational when the engine
is running.
Automatic mode AUTO
Basic setting for maximum comfort:
● Switch on the fan.
● Press AUTO; fan speed, air
distribution, cooling and air
recirculation are regulated
automatically.
● Set the desired temperature.
● Open all air vents.
To switch off the electronic climate
control system, switch off the fan.
Temperature preselection
Temperatures can be set to the
desired value.
If the minimum temperature is set, the
climate control system runs at
maximum cooling.
If the maximum temperature is set,
the climate control system runs at
maximum heating.
Demisting and defrosting the
windows
● Press Ê; LED illuminates in the
button when activated.
● Temperature, air distribution and
cooling are regulated
automatically and the fan runs at
high speed.
● Switch on heated rear window Ü
To return to Automatic mode: press
Ê
or AUTO.
Note
If Ê is pressed while the engine is
running, an Autostop will be inhibited
until Ê is pressed again.
If Ê is pressed while the engine is in
an Autostop, the engine will restart
automatically.
Stop-start system 3 136.
Instruction settings
Instructionly changing any of the
following settings will deactivate
Automatic mode:
Fan speed Z
Adjust the air flow instructionly by
switching the fan to the desired
speed.
If the fan is switched off, the air
conditioning is also deactivated.
Air distribution M
Press appropriate button for desired
adjustment. LED illuminates in the
button when activated.
R
: to windscreen and front door
windows
M
: to head area
S
: to foot well
Combinations of settings are possible
by pressing two buttons until both
LEDs are illuminated.
To return to Automatic mode: Press
AUTO button.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
120
Climate control
Cooling A/C
The air conditioning system cools and
dehumidifies (dries) the air when
outside temperature is above a
specific level. Therefore
condensation may form and drip from
under the vehicle.
Note
Air conditioning performance is
reduced when ECO mode has been
If no cooling or drying is required
press A/C OFF to switch the cooling
system off, thus saving fuel. LED
illuminates in the button.
To return to Automatic mode: Press
AUTO button.
Air recirculation mode u
Activate or deactivate instruction air
recirculation mode with u. LED
illuminates in the button when
activated.
9 Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling the air
humidity increases, so the
windows may mist up from inside.
The quality of the passenger
compartment air deteriorates,
which may cause the vehicle
occupants to feel drowsy.
To return to Automatic mode: Press
AUTO button.
Rear heating system
The rear passenger compartment
heating fan assists air flow to the rear
passenger compartment via the rear
air vents.
The rate of air flow is determined by
the fan. Air temperature is controlled
using the temperature control on the
instrument panel.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
121
To operate the heating fan, press -
to activate the heating fan. The
heating fan is activated if both the
LED of the button and the LED of the
fan control at the roof are not
illuminated.
Set the heating fan y to regulate the
amount of heated air to be flown into
the rear passenger compartment.
Rear air conditioning
system
The rear air conditioning system is
actuated in conjunction with the front
passenger compartment air
conditioning system.
Rear air conditioning fan switch
The rear air conditioning fan assists
air flow to the rear passenger
compartment via the rear air vents.
The rate of air flow is determined by
the fan.
To allow cooled and dehumidified
(dried) air to be distributed:
Press A/C OFF to switch on the air
conditing system. The system is
operating if the LED of the button is
not illuminated.
Press - to activate the rear air
conditioning fan. The fan is activated
if both the LED of the button and the
LED of the fan control at the roof are
not illuminated.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
122
Climate control
Set the fan < to regulate the amount
of cooled air to be flown into the rear
passenger compartment.
Auxiliary heater
Coolant heater
The engine-independent, fuel-
powered coolant heater provides
rapid heating of the engine coolant to
enable heating of the vehicle interior
without the engine running.
9 Warning
Do not operate the system when
refuelling, when dust or
combustible vapours are present
or in enclosed spaces (e.g.
garage).
Before starting or programming the
system to start, turn the vehicle's
climate control system to heat, set the
air distribution to V and turn the fan
on.
Switch off when not required. Heating
stops automatically after the
programmed runtime. It will also
cease to operate if the vehicle fuel
level drops too low.
During operation, power from the
vehicle battery is used. The driving
time should therefore be at least as
long as the heating time. For short
journey times, check the vehicle
battery regularly and recharge if
necessary.
To ensure efficient performance,
briefly operate the auxiliary heater
once a month.
Control units
The timer or remote control unit turns
the system on and off, and is used to
programme specific departure times.
Timer (Type A)
1 Display : Displays preset, current
time or preset time,
temperature, Y, Ö and x
2 l
: Adjusts values up
3 7
: Long press: switch
heater on, short press:
turns display on or
confirms selection
4 d
: Long press: switch
heater off, short press:
turns display on or exit
menu
5 k
: Adjusts values down
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
123
Remote control (Type A)
1 Display : Displays preset, current
time or preset time,
temperature, Z, Ü, Y,
Ö
and x
2 7 : Long press: switch heater on,
short press: turns display on
or confirms selection
3 l : Adjusts values up
4 d : Long press: switch heater off,
short press: turns display on
or exit menu
5 k : Adjusts values down
If no buttons are pressed within
ten seconds the display automatically
turns off.
Remote control (Type A) fault
displays
INIT
: automatic detection –
wait until automatic
detection is finished
NO
SIGNAL
: no signal –
check heater fuse
Z
: poor signal –
move closer
Ü
: battery low –
replace battery
Y
: heater fault –
consult workshop
Add, AddE : system in learning
mode
Teach remote control (Type A)
If the vehicle battery is reconnected,
the LED in the instrument panel
button illuminates and the system
configures the remote control menu
automatically. If the LED flashes,
select Add or AddE and confirm.
Additional remote control units may
also be configured. Press the button
until LED flashes, switch on the
remote control, select Add and
confirm.
AddE teaches the current remote
control unit exclusively and blocks all
previously configured units. Add
teaches up to four remote control
units, but only one unit can operate
the system at any one time.
Remote control (Type B)
1 Display : Displays preset, current
time or preset time,
temperature, Z, Ü, Y,
Ö
and x
-------------------------------------------------------------------------------------------------------------------------------------------------------------
124
Climate control
2 l : Adjusts values up
3
OFF
: Switch heater off, or press
Y and OFF simultaneously
to confirm selection
4 Y : Switch heater on, or press Y
and OFF simultaneously to
confirm selection
5 k : Adjusts values down
If no buttons are pressed within
30 seconds the display automatically
turns off.
9 Warning
When refuelling, switch off the
remote control unit as well as the
heater!
The remote control has a maximum
range of 1000 metres. The range may
be reduced due to environmental
conditions and as the battery
becomes weaker.
Remote control (Type B) fault
displays
Z
: poor signal – adjust position
FAIL : error during signal
transmission –
move closer or check heater
fuse
Ü
: battery low – replace battery
Teach remote control (Type B)
Up to four additional remote control
units may also be configured. During
additional teaching processes, the
oldest transmitter will be deleted each
time.
Remove the heater fuse for
five seconds, then refit the fuse.
Within two - six seconds press OFF
for one second. Teaching is
completed.
If the remote has not been used for a
long period, press the OFF button six
times at intervals of two seconds,
then press and hold for another
two seconds, then wait two minutes.
Instruction control
Depending on version, the auxiliary
heater can also be switched on for the
last duration time or the default
duration 30 minutes, or cut-off
immediately, using the button on the
lower part of the instrument panel,
beside the steering wheel.
The LED in the button confirms
operation.
Battery replacement
Replace the battery when the range
of the remote control is reduced or
when the battery charge symbol
flashes.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
125
Open the cover and replace the
battery (Type A: CR 2430, Type B:
2CR 11108, or equivalent), ensuring
the new battery is correctly installed
with the positive (<) side facing the
positive terminals. Replace the cover
securely.
Dispose of old batteries in
accordance with environmental
regulations.
Batteries do not belong in household
waste. They must be disposed of at
an appropriate recycling collection
point.
Operation (Type A)
Heating Y
Select Y in the menu bar and press
G
to confirm. The predetermined
heating duration, e.g. L 30, flashes in
the display. The factory setting is
30 minutes.
Adjust the heating duration using k
or l and confirm. The value can be
set from ten to 120 minutes. Due to
the power consumption, note the
heating duration.
To switch off, select Y in the menu bar
again and press d.
Ventilation x
Select x in the menu bar and press
G
to confirm.
Adjust the ventilation duration using
k
or l and confirm. The value can
be set from ten to 120 minutes. Due
to the power consumption, note the
heating duration.
To switch off, select x in the menu bar
again and press d.
Programming P
Up to three preset departure times
can be programmed, either during
one day or over one week.
● Select P in the menu bar and
press G to confirm.
● Select desired preset memory
number P1, P2 or P3 and
confirm.
● Select F and confirm.
● Select weekday or weekday
group and confirm.
● Select hour and confirm.
● Select minutes and confirm.
● Select Y or x and confirm.
● Select ECO or HIGH and confirm.
● Select duration and confirm.
● Press d to exit.
Repeat the procedure to programme
the other preset memory numbers if
required.
To activate a desired preset memory
number select P1, P2 or P3, then
select On and confirm.
When a program is activated P and
Y will be displayed together.
To deactivate a preset memory,
select P1, P2 or P3, then select Off
and confirm.
Heating stops automatically
five minutes after the programmed
departure time.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
126
Climate control
Note
The remote control system features
a temperature sensor which
calculates the runtime according to
the ambient temperature and the
desired heating level (ECO or
HIGH). The system starts
automatically between five and
60 minutes prior to the programmed
departure time.
Set time and weekday Þ
If the vehicle battery is disconnected
or its voltage is too low, the unit will
need to be reset.
● Select F in the menu bar and
confirm.
● Select Þ in the menu bar and
confirm.
● Adjust using k or l to change
the hour and confirm.
● Adjust using k or l to change
the minutes and confirm.
● Press d to exit.
● Select F in the menu bar and
confirm.
● Select Mo in the menu bar and
confirm.
● Adjust using k or l to change
the weekday and confirm.
● Press d to exit.
Heating level
The preferred heating level for
programmed departure times can be
set to either ECO or HIGH.
● Select Y in the menu bar and
confirm.
● Select ECO or HIGH and confirm.
● Press d to exit.
Operation (Type B)
Heating Y or Ventilation x
Select the operating mode Y or x, if
necessary.
● Press l three times.
● Press Y and OFF
simultaneously, Y or x flashes.
● Adjust using k or l to select Y
or x.
● Press Y and OFF simultaneously
to confirm.
To switch on, press Y for
one second. The predetermined
heating duration, e.g. 30, is
displayed. The factory setting is
30 minutes.
The heating duration can be set in
increments of ten minutes. Due to the
power consumption, note the heating
duration.
● Press l four times.
● Press Y and OFF
simultaneously, Y/x flashes.
● Adjust using k or l to select the
desired heating duration.
● Press Y and OFF simultaneously
to confirm.
To switch off, press OFF.
Programming y
The system calculates the operating
time of the heater depending on the
temperature inside the vehicle.
● Press k twice.
● Press Y and OFF
simultaneously, y flashes.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
127
● Adjust using k or l to select the
departure time.
● Press Y and OFF simultaneously
to confirm.
To switch on, press Y for one second,
HTM is displayed.
Heating stops automatically after the
programmed departure time, or can
be instructionly switched off.
● Press k twice.
● Press OFF for one second, HTM
goes out.
Set time
If the vehicle battery is disconnected
or its voltage is too low, the time will
need to be reset.
● Press l once.
● Press Y and OFF
simultaneously, Ö flashes.
● Adjust using k or l to set the
time.
● Press Y and OFF simultaneously
to confirm.
Heating level
The preferred heating level for
programmed departure times can be
set to between C1 and C5.
● Press k three times.
● Press Y and OFF
simultaneously, Y flashes.
● Adjust using k or l to set the
heating level.
● Press Y and OFF simultaneously
to confirm.
To display the passenger
compartment temperature, press l
twice.
Air vents
Adjustable air vents
At least one air vent must be open
while cooling is on, in order to prevent
the evaporator from icing up due to
lack of air movement.
9 Warning
Do not attach any objects to the
slats of the air vents. Risk of
damage and injury in case of an
accident.
Centre air vents
-------------------------------------------------------------------------------------------------------------------------------------------------------------
128
Climate control
To open or close the centre air vents
and direct the flow of air, tilt the slats
up or down and turn the adjuster
wheel left or right.
Side air vents
To open or close the side air vents, tilt
the slats up or down.
Direct the flow of air by rotating the
vents.
Depending upon the position of the
temperature control, air will be
directed into the vehicle via the side
air vents.
Rear air vents
Depending on vehicle, additional
adjustable air vents are located in the
rear passenger compartment.
Fixed air vents
Additional air vents are located
beneath the windscreen and door
windows, in the foot wells and,
depending on vehicle, in the rear
passenger compartment.
Glovebox cooler
The air conditioning system can also
keep the contents of the glovebox
cool.
Maintenance
Air intake
The air intake in front of the
windscreen in the engine
compartment must be kept clear to
allow air intake. Remove any leaves,
dirt or snow.
Pollen filter
The pollen filter cleans dust, soot,
pollen and spores from the air
entering the vehicle through the air
intake.
Note
Pollen filter is only fitted to vehicles
with air conditioning system.
Air conditioning regular
operation
In order to ensure continuously
efficient performance, cooling must
be operated for a few minutes once a
month, irrespective of the weather
and time of year. Operation with
cooling is not possible when outside
temperature is too low.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
129
Service
For optimal cooling performance, it is
recommended to annually check the
climate control system, starting
three years after initial vehicle
registration, including:
● functionality and pressure test
● heating functionality
● leakage check
● check of drive belts
● cleaning of condenser and
evaporator drainage
● performance check
Note
Refrigerant R-134a contains
fluorinated greenhouse gases with a
global warming potential of 1430.
Front air conditioning system is filled
with 0.58 kg and has a CO
2
equivalent of 0.83 tonnes, the front
and rear air conditioning system is
filled with 0.88 kg and has a CO
2
equivalent of 1.26 tonnes.
Depending on vehicle, information
regarding air conditioning refrigerant
appears on a label located in the
engine compartment.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
130
Driving and operating
Driving and
operating
Driving hints . . . . . . . ... 130
Driving economically . . . ... 130
Control of the vehicle . . . ... 131
Steering . . . . . . . . ... 131
Starting and operating . . . ... 132
New vehicle running-in . . . 132
Ignition switch positions . . ... 132
Power button . . . . . . ... 132
Starting the engine . . . . .. 134
Idle speed control . . . . . 135
Vehicle shutdown . . . . . 135
Overrun cut-off . . . . . . 136
Stop-start system . . . . . 136
Parking . . . . . . . . . 139
Engine exhaust . . . . . . .. 140
Diesel particle filter . . . . .. 140
Catalytic converter . . . . ... 140
AdBlue . . . . . . . . . . 141
Manual transmission . . . . .. 146
Brakes . . . . . . . . . . 147
Antilock brake system . . . . 147
Parking brake . . . . . . .. 148
Brake assist . . . . . . . . 148
Hill start assist . . . . . . . 148
Ride control systems . . . . . 149
Traction Control system . . .. 149
Electronic stability program . . 150
Driver assistance systems . . . 152
Cruise control . . . . . . .. 152
Speed limiter . . . . . . ... 155
Parking assist . . . . . . .. 155
Rear view camera . . . . ... 157
Fuel . . . . . . . . . . . 159
Fuel for diesel engines . . . 159
Refuelling . . . . . . . . 160
Fuel consumption - CO
2
-
Emissions . . . . . . . ... 161
Trailer hitch . . . . . . . . 162
General information . . . . . 162
Driving characteristics and
towing tips . . . . . . . .. 162
Trailer towing . . . . . . ... 162
Trailer stability assist . . . ... 163
Driving hints
Driving economically
ECO mode
ECO mode is a function that
optimises fuel consumption. It affects
engine power and torque,
acceleration, gear shift indication,
heating, air conditioning and electrical
consumers.
Activation
Press ECO. Control indicator ECO
illuminates in the instrument cluster
when activated.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Driving and operating
131
Note
The use of ECO mode may affect the
performance of the climate control
During driving, it is possible to
temporarily disable ECO mode, e.g.
to increase engine performance, by
depressing the accelerator pedal
firmly.
ECO mode is reactivated when
pressure is reduced on the
accelerator pedal.
Deactivation
Press ECO again. Control indicator
ECO extinguishes in the instrument
cluster.
Control of the vehicle
Never coast with engine not
running (except during Autostop)
Many systems will not function in this
situation (e.g. brake servo unit, power
steering). Driving in this manner is a
danger to yourself and others. All
systems function during an Autostop,
but there may be a controlled
reduction in power steering assist and
vehicle speed is reduced.
Stop-start system 3 136.
Pedals
To ensure the pedal travel is
uninhibited, there must be no mats in
the area of the pedals.
Use only floor mats which fit properly
and are fixed by the retainers on the
driver's side.
Driving downhill
Engage a gear when driving downhill
to ensure that sufficient brake
pressure is available.
Steering
If power steering assist is lost
because the engine stops or due to a
system malfunction, the vehicle can
be steered but may require increased
effort.
Caution
Vehicles equipped with hydraulic
power steering:
If the steering wheel is turned until
it reaches the end of its travel, and
is held in that position for more
than 15 seconds, damage may
occur to the power steering
system and there may be loss of
power steering assist.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
132
Driving and operating
Starting and operating
New vehicle running-in
Do not brake unnecessarily hard for
the first few journeys and after new
disc brake pads have been fitted.
During the first drive, smoke may
occur because of wax and oil
evaporating off the exhaust system.
Park the vehicle in the open for a
while after the first drive and avoid
inhaling the fumes.
During the running-in period, fuel and
engine oil consumption may be
higher and the cleaning process of
the diesel particle filter may take
place more often. Autostop may be
inhibited to allow for charging the
vehicle battery.
Stop-start system 3 136.
Diesel particle filter 3 140.
Ignition switch positions
Turn key:
0 : ignition off: Some functions
remain active until key is
removed or driver's door is
opened, provided the ignition was
on previously
1 : accessory power mode: Steering
wheel lock released, some
electrical functions are operable,
ignition is off
2 : ignition is on, diesel engine is
preheating. Control indicators
illuminate and most electrical
functions are operable
3 : engine start: Release key after
starting procedure begins
Steering wheel lock
Remove key from ignition switch and
turn steering wheel until it engages.
9 Danger
Never remove the key from
ignition switch during driving as
this will cause steering wheel lock.
Power button
Electronic key must be inside the
vehicle, either in the card reader or
the front passenger compartment.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Driving and operating
133
If the electronic key is not inside the
vehicle, a corresponding message
appears in the Driver Information
Note
Do not put the electronic key in the
load compartment during driving, as
this is outside of the detection zone
(indicated by a warning chime at low
speed 3 104 and a message in the
Driver Information Centre 3 103).
Note
In the event the electronic key is kept
in the front passenger compartment
and a message appears in the Driver
Information Centre (possibly
accompanied by a warning chime)
indicating that it is out of reception
range, we recommend inserting the
electronic key in the card reader.
Some functions, e.g. Infotainment
system, are available for use as soon
as you enter the vehicle.
Accessory power mode
Press START/STOP without
operating clutch or brake pedal to
enable further electrical functions to
be operated.
These functions switch off
automatically after a delay.
Engine start
Operate clutch and brake pedal and
press START/STOP. Release button
after starting procedure begins.
If a gear is engaged, the engine can
be started only by operating the clutch
pedal and pressing the
START/STOP button.
In some cases, it may be necessary
to move the steering wheel slightly
while pressing START/STOP to
release the steering wheel lock. A
corresponding message appears in
the Driver Information Centre 3 102.
At very low outside temperatures (e.g.
below -10 °C) keep the clutch pedal
depressed while pressing
START/STOP until the engine starts.
If one of the starting conditions is not
applied, a corresponding message
appears in the Driver Information
Centre 3 102.
Vehicle messages 3 103.
Engine stop
Electronic key must be inside the
vehicle, either in the card reader or
the front passenger compartment.
With the vehicle stationary, press
START/STOP to stop the engine. The
steering wheel lock is engaged when
the driver's door is opened and the
vehicle is locked.
If the electronic key is not detected, a
corresponding message appears in
the Driver Information Centre 3 102.
In this event, press START/STOP for
two seconds to stop the engine.
Central locking system 3 26.
Retained power off
Press START/STOP for more than
two seconds; the engine is stopped
while some functions, e.g.
Infotainment system, are available for
use for approx. 10 minutes.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
134
Driving and operating
These functions stop working when
the driver's door is opened and the
vehicle is locked.
Note
Always take the electronic key with
you when exiting the vehicle.
The electronic key being left in the
card reader is indicated by a warning
chime 3 104 and a message in the
Driver Information Centre 3 103
when the driver's door is opened.
9 Danger
Never leave an electronic key
inside the vehicle when children or
animals are left in the vehicle, to
avoid unintended operation of
windows, doors or engine. Risk of
fatal injury.
Fault
If the engine cannot be started, the
cause may be one of the following:
● Fault in electronic key.
● Electronic key out of reception
range.
● Battery voltage too low.
● Overload of the central locking
system by operating at frequent
intervals, the power supply is
interrupted for a short time.
● Interference from higher-power
radio waves from other sources.
Battery replacement 3 22.
Central locking system 3 26.
Electronic key system 3 24.
Starting the engine
Manual transmission: operate clutch.
Do not accelerate.
Diesel engines: turn the key to
position 2 for preheating until control
indicator ! extinguishes in the
instrument cluster 3 100.
Turn key to position 3 and release.
The increased engine speed
automatically returns to normal idling
speed as the engine temperature
rises.
Start attempts should not last longer
than 15 seconds. If engine does not
start, wait 15 seconds before
repeating starting procedure. If
necessary, depress accelerator
before repeating starting procedure.
Before restarting or to switch off the
engine, turn key back to 0.
During an Autostop, the engine can
be started by depressing the clutch
pedal.
Stop-start system 3 136.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст