Chevrolet Silverado / GMC Sierra. Service manual — part 2261
FRONT SIDE DOOR MOLDING REPLACEMENT (GMC DENALI)
Fig. 23: View Of Front Side Door Molding (GMC Denali)
Courtesy of GENERAL MOTORS CORP.
HOOD FRONT MOLDING REPLACEMENT (CHEVROLET V22)
Callout
Component Name
1
Front Side Door Molding
Tip:
1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should
remain 21°C (70°F) for one hour after assembly to allow adhesive to develop
sufficient bond strength.
2. Using a J 25070 Heat Gun in a circular motion, warm the front side door molding
prior to removal. Carefully clean the body panel thoroughly prior to bonding the new
front body side molding to the door.
3. Ensure the front door is in the closed position prior to installing the new front side
door moldings.
4. Remove the protective liner from the backside of the molding adhesive tape.
5. Position the pin on the backside of the molding to the round hole at the front edge of
the rear door first, then to the oval hole at the rear edge of the door.
6. Ensure full adhesion of the molding to the door using the palm of the hand with a
clean dry towel working from the rear edge of the door to the front, down the entire
molding.
2008 Chevrolet Silverado 1500
2008 ACCESSORIES & EQUIPMENT Exterior Trim - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
Fig. 24: View Of Hood Front Molding (Chevrolet V22)
Courtesy of GENERAL MOTORS CORP.
HOOD FRONT MOLDING REPLACEMENT (GMC HD)
Callout
Component Name
Preliminary Procedure:
Release the hood in order to access the front hood molding.
1
Hood Front Molding Locator Tab
Tip: Position the locator tab first into the hood panel center hole followed by the remaining
retainers.
2
Hood Front Molding Retainer Clips
Tip: Secure the retainer clips working from the center of the molding, outward until all the
clips are secure to the hood.
3
Hood Front Molding
2008 Chevrolet Silverado 1500
2008 ACCESSORIES & EQUIPMENT Exterior Trim - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
Fig. 25: View Of Hood Front Molding (GMC HD)
Courtesy of GENERAL MOTORS CORP.
HOOD FRONT MOLDING REPLACEMENT (GMC DENALI)
Callout
Component Name
Preliminary Procedure:
Release the hood in order to access the front hood molding.
1
Hood Front Molding Locator Tab
Tip: Position the locator tab first into the hood panel center hole followed by the remaining
retainers.
2008 Chevrolet Silverado 1500
2008 ACCESSORIES & EQUIPMENT Exterior Trim - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
Fig. 26: View Of Hood Front Molding (GMC Denali)
Courtesy of GENERAL MOTORS CORP.
HOOD REAR MOLDING REPLACEMENT (CHEVROLET HD)
Callout
Component Name
Preliminary Procedure:
Open the hood in order to access and remove the front hood molding.
1
Hood Front Molding Assembly
Tip:
1. Release the integral retainers from the hood.
2. Upon installation, align the left hand center retainer first into the hood as indicated.
3. Gently secure the remaining retainers working from left to right across the entire
hood front molding.
2008 Chevrolet Silverado 1500
2008 ACCESSORIES & EQUIPMENT Exterior Trim - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст