Chevrolet Silverado / GMC Sierra. Service manual — part 2262
Fig. 27: View Of Hood Rear Molding (Chevrolet HD)
Courtesy of GENERAL MOTORS CORP.
PICKUP BOX SIDE UPPER MOLDING REPLACEMENT (HD)
Callout
Component Name
1
Hood Rear Molding Screw (Qty: 2)
Tighten:: 1.5 N.m (13 lb in)
NOTE:
Refer to Fastener Notice .
2
Hood Rear Molding Assembly Nut (Qty: 2)
3
Hood Rear Molding Integral Clip (Qty: 4)
Tip: Ensure all four clips are fully seated prior to installing the hood rear molding screws.
4
Hood Rear Molding
Tip: Gently pry the hood molding upward, in order to remove.
2008 Chevrolet Silverado 1500
2008 ACCESSORIES & EQUIPMENT Exterior Trim - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
Fig. 28: Viwe Of Pickup Box Side Upper Molding (HD)
Courtesy of GENERAL MOTORS CORP.
ROOF PANEL JOINT FINISH MOLDING REPLACEMENT
Callout
Component Name
1
Pick Up Box Side Upper Molding Locators (Qty: 3)
Tip: Upon installation of the new molding, align the 3 locators to the pick up box side rail
and secure the retainers.
2
Pick Up Box Side Upper Molding Retainers (Qty: 23)
3
Pick Up Box Side Upper Molding
2008 Chevrolet Silverado 1500
2008 ACCESSORIES & EQUIPMENT Exterior Trim - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
Fig. 29: View Of Roof Panel Joint Finish Molding
Courtesy of GENERAL MOTORS CORP.
Callout
Component Name
1
Roof Panel Joint Finish Molding (Rear)
Tip:
1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should
remain 21°C (70°F) for one hour after assembly to allow adhesive to develop
sufficient bond strength.
2. Remove the roof panel finish joint from the roof ditch.
3. Use of a heat gun is recommended.
4. Using a 50/50 mixture of isopropyl alcohol and clean drinkable water and a clean
towel, remove the left over adhesive residue from the ditch.
5. Wipe the roof ditch clean with a clean dry towel.
6. Peel the adhesive tape backing from the roof panel joint finish molding.
7. Secure the molding starting at the front edge working rearward.
8. Completely wet out the roof panel finish joint molding.
NOTE:
Refer to Exterior Trim Emblem Removal Notice .
2008 Chevrolet Silverado 1500
2008 ACCESSORIES & EQUIPMENT Exterior Trim - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
REAR SPOILER REPLACEMENT (901/902)
Fig. 30: View Of Rear Spoiler (901/902)
Courtesy of GENERAL MOTORS CORP.
Callout
Component Name
1
Endgate Spoiler Assembly Screws (Qty: 4)
Tighten: 10 N.m (89 lb in)
NOTE:
Refer to Fastener Notice .
2
Endgate Spoiler Assembly Locator Pin
3
Endgate Spoiler Assembly Adhesive Tape Liner
Tip:
The part and surface should be ambient temperature prior to installation. The vehicle
should remain ambient temperature for one hour after assembly to allow adhesive to
develop sufficient bond strength.
Release the liner and wet out once the endgate spoiler is in position and the screws
2008 Chevrolet Silverado 1500
2008 ACCESSORIES & EQUIPMENT Exterior Trim - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст