Mitsubishi ASX (2018 year). Manual — part 8

Information screen (when the

ignition switch or the operation

mode is ON)

E00521100576

Each time you lightly press the multi-infor-
mation meter switch, the display screen
switches in the following order.

Type 1

Type 2

When there is no warning display

When there is a
warning display

1- Odometer (Type1)/Tripmeter
2- Odometer (Type1)/Tripmeter

3- Service reminder
4- Engine coolant temperature display

(Type 1)

5- Driving range display (Type 1)
6- Average speed display, average fuel

consumption display, momentary fuel
consumption display (Type 1)

7- Driving range display, momentary fuel

consumption display (Type 2)

8- Average fuel consumption display, mo-

mentary fuel consumption display (Type
2)

9- Average speed display, momentary fuel

consumption display (Type 2)

10- Function setting screen
11- Redisplay of a warning display screen

NOTE

While driving, even if you operate the multi-
information meter switch, the function set-
ting screen is not displayed. Always stop the
vehicle in a safe place before operating.
Refer to “Changing the function settings
(when the ignition switch or the operation
mode is ON)” on page 5-19.

When there is information to be announced,
such as a system fault, the buzzer sounds
and the screen display is switched.
Refer to “Interrupt display screen (when the
ignition switch or the operation mode is
ON)” on page 5-14.

Odometer/Tripmeter

E00568400046

Type 1

Type 2

The operation method is the same as when
the ignition switch or the operation mode is
OFF.
Refer to “Odometer/Tripmeter” for further
details on page 5-06.

Multi-information display

5-10

OGAE18E1

Instruments and controls

Service reminder

E00522500694

This displays the distance
and number of months until
the next periodic inspection.
Refer to “Service reminder”
on page 5-16.

Type 2

Type 1

Engine coolant temperature

display

E00521400566

This indicates the engine
coolant temperature.
If the coolant becomes hot,
“ ” will blink.
Pay careful attention to the
engine coolant temperature
display while you are driv-
ing.

CAUTION

If the engine is overheating, “ ” will blink.
In this case, the bar graph is on the red zone.
lmmediately park the vehicle in a safe place
and take the required measures. Refer to
“Engine overheating” on page 8-04.

Driving range display

E00568500047

This displays the approximate driving range
(how many more kilometres or miles you can
drive). When the driving range falls below
approximately 50 km (30 miles), “---” is dis-
played.

Type 1

Type 2

Refuel as soon as possible.

Type 1

Type 2

NOTE

The driving range is determined based on
the fuel consumption data. This may vary
depending on the driving conditions and
habits. Treat the distance displayed as just a
rough guideline.

When you refuel, the driving range display
is updated.
However, if you only add a small amount of
fuel, the correct value will not be displayed.
Fill with a full tank whenever possible.

On rare occasions, the value displayed for
the driving range may change if you are
parked on an extremely steep incline. This is
due to the movement of fuel in the tank and
does not indicate a malfunction.

Multi-information display

5-11

OGAE18E1

Instruments and controls

NOTE

The display setting can be changed to the
preferred units (km or miles).
Refer to “Changing the function settings
(when the ignition switch or the operation
mode is ON)” on page 5-19.

Average speed display

E00568600048

This displays the average speed from the last
reset to the present time.
There are the following 2 mode settings.
For the method for changing the average
speed display setting, refer to “Changing the
function settings (when the ignition switch or
the operation mode is ON)” on page 5-19.

Type 1

Type 2

Manual reset mode

When the average speed is being dis-
played, if you hold down the multi-infor-
mation meter switch, the average speed
displayed at that time is reset.

When the following operation is per-
formed, the mode setting is automatical-
ly switched from manual to auto.
[Except for vehicles equipped with key-
less operation system]
Turn the ignition switch from the
“ACC” or “LOCK” position to the “ON”
position.
[For vehicles equipped with keyless op-
eration system]
Change the operation mode from ACC
or OFF to ON.

Switching to auto occurs automatically.
If switching to manual mode is done,
however, the data from the last reset is
displayed.

Auto reset mode

When the average speed is being dis-
played, if you hold down the multi-infor-
mation meter switch, the average speed
displayed at that time is reset.

When the engine switch or the operation
mode is in the following conditions, the
average speed display is automatically
reset.
[Except for vehicles equipped with key-
less operation system]
The ignition switch is in the “ACC” or
“LOCK” position for about 4 hours or
longer.

NOTE

The average speed display and the average
fuel consumption display can be reset indi-
vidually for the auto reset mode and manual
reset mode.

“---” is displayed when the average speed
cannot be measured.

The initial (default) setting is “Auto reset
mode”.

The display setting can be changed to the
preferred units (km/h or mph).
Refer to “Changing the function settings
(when the ignition switch is “ON”)” on page
5-19.

The memory of the auto reset mode or man-
ual reset mode for the average speed display
is erased if the battery is disconnected.

Average fuel consumption dis-

play

E00568700137

This displays the average fuel consumption
from the last reset to the present time.

Multi-information display

5-12

OGAE18E1

Instruments and controls

There are the following 2 mode settings.
For information on how to change the aver-
age fuel consumption display setting, refer to
“Changing the function settings (when the ig-
nition switch or the operation mode is ON)”
on page 5-19.

Type 1

Type 2

The “ ” mark (A) in the momentary fuel
gauge shows the average fuel consumption.
(Type 2)

Manual reset mode

When the average fuel consumption is
being displayed, if you hold down the
multi-information meter switch, the
average fuel consumption displayed at
that time is reset.

Auto reset mode

When the average fuel consumption is
being displayed, if you hold down the
multi-information meter switch, the
average fuel consumption displayed at
that time is reset.

When the engine switch or the operation
mode is in the following conditions, the
average fuel consumption display is au-
tomatically reset.
[Except vehicles equipped with keyless
operation system]
The ignition switch is in the “ACC” or
“LOCK” position for about 4 hours or
longer.
[For vehicles equipped with keyless op-
eration system]
The operation mode is in ACC or OFF
for about 4 hours or longer.

NOTE

The average speed display and the average
fuel consumption display can be reset indi-
vidually for the auto reset mode and manual
reset mode.

“---” is displayed when the average fuel con-
sumption cannot be measured.

The initial (default) setting is “Auto reset
mode”.

The average fuel consumption depends on
the driving condition (road condition, driv-
ing behavior, etc.). The displayed fuel con-
sumption may vary from the actual fuel con-
sumption. Treat the fuel consumption dis-
played as just a rough guideline.

The memory of the auto reset mode or man-
ual reset mode for the average fuel con-
sumption display is erased if the battery is
disconnected.

Multi-information display

5-13

OGAE18E1

Instruments and controls

NOTE

The display setting can be changed to the
preferred units {km/L, mpg (US), mpg (UK)
or L/100 km}.
Refer to “Changing the function settings
(when the ignition switch or the operation
mode is ON)” on page 5-19.

Momentary fuel consumption

display

E00568800040

While driving, this displays the momentary
fuel consumption, using a bar graph.

Type 2

Type 1

When the value of momentary fuel consump-
tion surpasses the value of average fuel con-
sumption, the momentary fuel consumption
is displayed with a white bar graph. (Type 2)

Be conscious of maintaining the value of mo-
mentary fuel consumption below the value of
average fuel consumption, driving with the
bet-ter fuel consumption can be possible.

NOTE

When the momentary fuel consumption can-
not be measured, the bar graph is not dis-
played.

It is possible to cancel the green bar graph.
Refer to “Changing the function settings
(when the ignition switch or the operation
mode is ON)” on page 5-19.

Function setting screen

E00521900271

The “Display language”,
“Temperature unit”, “Fuel
consumption

unit”,

and

“Average fuel consumption
and speed reset method” etc.
settings can be modified as

desired.
Refer to “Changing the function settings
(when the ignition switch or the operation
mode is ON)” on page 5-19 for further de-
tails.

Interrupt display screen (when

the ignition switch or the oper-

ation mode is ON)

E00522000673

Warning display

When there is information to be announced,
such as a system fault, a sound is emitted and
the information screen switches to the warn-
ing display screen.
Refer to the warning list and take the neces-
sary measures.
Refer to “Warning display list (when the ig-
nition switch or the operation mode is ON)”
on page 5-31.
When the cause of the warning display is
eliminated, the warning display goes out au-
tomatically.

To return to the screen displayed before
the warning display
Even if the cause of the warning display is
not eliminated, you can return to the screen
that was displayed before the warning dis-
play.

Multi-information display

5-14

OGAE18E1

Instruments and controls

If you press the multi-information meter
switch, the display screen switches to the
screen that was displayed before the warning
display and the mark (A) is displayed.

Type 1

Type 2

NOTE

Warning display screens with a “ ” or “ ”
mark displayed in the upper right of the
screen can be switched. If you want to
switch the display, press the multi-informa-
tion meter switch as follows.
“ ”: Press lightly.
“ ”: Press for about 2 seconds or more.

Redisplay of a warning display

screen

When the mark is displayed, if you lightly
press the multi-information meter switch a
few times, the warning display screen you
switched from is displayed again.

Other interrupt displays

The operation status of each system is dis-
played on the information screen.
Refer to the appropriate page in the warning
display list for further details.
Refer to “Other interrupt displays” on page
5-42.

Selector lever position display

screen*

E00532500323

Shows the position of the se-
lector lever.
Refer to “Selector lever op-
eration” on page 6-33.

Outside temperature display

screen

E00522100300

This shows the temperature
outside the vehicle.

NOTE

The display setting can be changed to the
preferred units (°C or °F).
Refer to “Changing the function settings
(when the ignition switch or the operation
mode is ON)” on page 5-19.

Depending on factors such as the driving
conditions, the displayed temperature may
vary from the actual outside temperature.

Fuel remaining display screen

E00522200402

This displays the amount of fuel remaining.

Type 1

Type 2

Multi-information display

5-15

OGAE18E1

Instruments and controls

CAUTION

For petrol-powered vehicles, do not run out
of fuel, or the catalytic converter may be ad-
versely affected. If the warning display ap-
pears, refuel as soon as possible.

For diesel-powered vehicles, do not drive
with an extremely low fuel level; running
out of fuel could cause damage to the fuel
system.

NOTE

It may take several seconds to stabilise the
display after refilling the tank.

If fuel is added with the ignition switch or
the operation mode is in ON, the fuel gauge
may incorrectly indicate the fuel level.

Fuel lid mark

E00522300070

The arrow (A) indicates that the fuel tank fill-
er is located on the left side of the body.

Fuel remaining warning display

E00522402235

When the fuel is reduced to about 10 litres*

or 7 litres*

, the information screen switches

to the interrupt display of the fuel remaining
warning display, and the “ ” mark (B) on the
fuel remaining display flashes slowly (about
once per second).
If the warning display appears, refuel as soon
as possible.

After a few seconds, the information screen
returns from the fuel remaining warning dis-
play to the previous screen.
If the remaining fuel level is reduced further,
the information screen switches to the fuel re-
maining warning display and the “ ” mark
(B) on the fuel remaining display flashes
quickly (about twice per second).

: Except for diesel-powered 1600 models

: Diesel-powered 1600 models

Type 1

Type 2

NOTE

On inclines or curves, the display may be in-
correct due to the movement of fuel in the
tank.

Service reminder

E00522500708

Displays the approximate time until the next
periodic

inspection

recommended

MITSUBISHI MOTORS. “---” is displayed
when the inspection time has arrived.

NOTE

Depending on the vehicle specifications, the
displayed time until the next periodic inspec-
tion may differ from that recommended by
MITSUBISHI MOTORS.
In addition, the display settings for the next
periodic inspection time can be modified.
To modify the display settings, have it adjus-
ted at a MITSUBISHI MOTORS Authorized
Service Point.
For more details, consult a MITSUBISHI
MOTORS Authorized Service Point.

Multi-information display

5-16

OGAE18E1

Instruments and controls

Type 1

Type 2

1. Displays the time until the next periodic

inspection.

NOTE

The distance is shown in units of 100 km
(100 miles). The time is shown in units of
months.

2. This informs you that a periodic inspec-

tion is due. We recommend you to con-
sult a MITSUBISHI MOTORS Author-
ized Service Point.

At that time, when the ignition switch is
switched from the “LOCK” position to
the “ON” position or the operation mode
is changed from OFF to ON, the warn-
ing display is displayed for a few sec-
onds on the information screen.

Type 1

Type 2

3. After your vehicle is inspected at a

MITSUBISHI MOTORS Authorized
Service Point, it displays the time until
the next periodic inspection.

To reset

The “---” display can be reset while the igni-
tion switch or the opertion mode is in OFF.
When the display is reset, the time until the
next periodic inspection is displayed and the
warning display is no longer displayed when
the ignition switch is turned from the
“LOCK” position to the “ON” position or the
operation mode is changed from OFF to ON.

1. When you lightly press the multi-infor-

mation meter switch a few times, the in-
formation screen switches to the service
reminder display screen.

Type 1

Type 2

Multi-information display

5-17

OGAE18E1

Instruments and controls

2. Press and hold the multi-information

meter switch for about 2 seconds or
more to display “ ” and make it flash.
(If there is no operation for about 10 sec-
onds with flashing, the display returns to
the previous screen.)

3. Lightly press the multi-information me-

ter switch while the icon is flashing to
change the display from “---” to
“CLEAR”. After this, the time until the
next periodic inspection will be dis-
played.

Type 1

Type 2

CAUTION

The customer is responsible for making sure
that periodic inspection and maintenance are
performed. Inspections and maintenance
must be performed to prevent accidents and
malfunctions.

NOTE

“---”display cannot be reset when the igni-
tion switch or the operation mode is in ON.

When “---” is displayed, after a certain dis-
tance and a certain period of time, the dis-
play is reset and the time until the next peri-
odic inspection is displayed.

If you accidentally reset the display, we rec-
ommend you to consult a MITSUBISHI
MOTORS Authorized Service Point.

Door ajar warning display

screen (when the ignition

switch or the operation mode is

ON)

E00522600565

Type 1

Type 2

If any of the doors or the tailgate is not com-
pletely closed, this displays the open door or
tailgate.
If the vehicle speed exceeds approximately
8 km/h (5 mph) while a door is ajar, a buzzer
sounds 4 times. This notifies the driver that a
door is ajar.

CAUTION

Before moving your vehicle, check that the
warning lamp is OFF.

Multi-information display

5-18

OGAE18E1

Instruments and controls

Changing the function settings

(when the ignition switch or the

operation mode is ON)

E00522702023

1. Stop the vehicle in a safe place.

Firmly apply the parking brake and put
the gearshift lever into the “N” (Neutral)
position (M/T) or the selector lever into
the “P” (Park) position (A/T or CVT).

2. Lightly press the multi-information me-

ter switch a few times to switch the in-
formation screen to the function setting
screen.
Refer to “Information screen (when the
ignition switch or the operation mode is
ON)” on page 5-10.

Type 1

Type 2

CAUTION

For safety, stop the vehicle before operating.
While driving, even if you operate the multi-
information meter switch, the function set-
ting screen is not displayed.

3. Press and hold the multi-information

meter switch for about 2 seconds or
more to switch from the setting mode
screen to the menu screen.

Type 1

Type 2

NOTE

To return the menu screen to the function
setting screen, press and hold the multi-in-
formation meter switch for about 2 seconds
or more.

NOTE

If no operations are made within about 15
seconds of the menu screen being displayed,
the display returns to the function setting
screen.

4. Select the item to change on the menu

screen and change to the desired setting.
Refer to the following items for further
details on the operation methods.
Refer to “Changing the reset mode for
average fuel consumption and average
speed” on page 5-20.
Refer to “Changing the fuel consump-
tion display unit” on page 5-21.
Refer to “Changing the temperature
unit” on page 5-22.
Refer to “Changing the display lan-
guage” on page 5-22.
Refer to “Operation sound setting” on
page 5-23.
Refer to “Changing the time until
“REST REMINDER” is displayed” on
page 5-23.
Refer to “Changing the turn-signal
sound” on page 5-24.
Refer to “Changing the momentary fuel
consumption display” on page 5-25.
Refer to “Reset of low tyre pressure
warning threshold” on page 6-76
Refer to “Tyre ID set change” on page
6-76

Multi-information display

5-19

OGAE18E1

Instruments and controls

Refer to “Returning to the factory set-
tings” on page 5-25.

Changing the reset mode for
average fuel consumption and
average speed

E00522900845

The mode conditions for the average fuel
consumption and average speed display can
be switched between “Auto reset” and “Man-
ual reset”.

1. Press and hold the multi-information

meter switch for about 2 seconds or
more to switch from the setting mode
screen to the menu screen.
Refer to “Changing the function settings
(when the ignition switch or the opera-
tion mode is ON)” on page 5-19.

2. Lightly press the multi-information me-

ter switch to select “AVG” (average fuel
consumption and average speed setting).

Type 1

Type 2

3. Press and hold the multi-information

meter switch for about 2 seconds or
more to switch in sequence from A or 1
(Auto reset mode) → M, 2 or P (Manual
reset mode) → A or 1 (Auto reset
mode).
The setting is changed to the selected
mode condition.

Manual reset mode

When the average fuel consumption and
average speed are being displayed, if
you hold down the multi-information
meter switch, the average fuel consump-
tion and average speed displayed at that
time are reset.

When the following operation is per-
formed, the mode setting is automatical-
ly switched from manual to auto.
[Except vehicles equipped with keyless
operation system]
Turn the ignition switch from the
“ACC” or “LOCK” position to the “ON”
position.
[For vehicles equipped with the keyless
operation system] Change the operation
mode from ACC or OFF to ON.

Switching to auto occurs automatically.
If switching to manual mode is done,
however, the data from the last reset is
displayed.

Auto reset mode

Multi-information display

5-20

OGAE18E1

Instruments and controls

When the engine switch or the operation
mode is in the following conditions, the
average fuel consumption display and
average speed display are automatically
reset.
[Except vehicles equipped with keyless
operation system]
The ignition switch is in the “ACC” or
“LOCK” position for about 4 hours or
longer.
[For vehicles equipped with keyless op-
eration system]
The operation mode is in ACC or OFF
for about 4 hours or longer.

NOTE

The average fuel consumption display and
average speed display can be reset individu-
ally for the auto reset mode and manual reset
mode.

The memory of the auto reset mode or man-
ual reset mode for the average fuel con-
sumption display and average speed display
is erased if the battery is disconnected.

The initial (default) setting is “Auto reset
mode”.

Changing the fuel consumption
display unit

E00523000579

The display unit for fuel consumption can be
switched. The distance, speed, and amount
units are also switched to match the selected
fuel consumption unit.

1. Press and hold the multi-information

2. Lightly press the multi-information me-

ter switch to select “AVG UNIT” (fuel
consumption display setting).

Type 1

Type 2

3. Press and hold the multi-information

meter switch for about 2 seconds or
more to display “AVG UNIT” (fuel con-
sumption display unit setting).

4. Lightly press the multi-information me-

ter switch to switch in sequence from
km/L → L/100 km → mpg (US) → mpg
(UK) → RETURN → km/L.

Type 1

Type 2

5. Press and hold the multi-information

meter switch for about 2 seconds or
more to change the setting to the selec-
ted unit.

NOTE

The display units for the driving range, the
average fuel consumption, the average speed
and the momentary fuel consumption are
switched, but the units for the indicating
needle (speedometer), the odometer and the
tripmeter will remain unchanged.

Multi-information display

5-21

OGAE18E1

Instruments and controls

NOTE

The memory of the unit setting is erased if
the battery is disconnected, and it returns au-
tomatically to L/100 km.

The distance and speed units are also switch-
ed in the following combinations to match
the selected fuel consumption unit.

Fuel con-
sumption

Distance

(driving

range)

Speed

(average

speed)

L/100 km

km/h

mpg (US)

mile(s)

mph

mpg (UK)

mile(s)

mph

km/L

km/h

Changing the temperature unit

E00523100466

The display unit for temperature can be
switched.

1. Press and hold the multi-information

2. Lightly press the multi-information me-

ter switch to select “ ” (temperature
unit setting).

Type 1

Type 2

3. Press and hold the multi-information

meter switch for about 2 seconds or
more to switch in sequence from °C →
°F → °C.
The setting is changed to the selected
temperature unit.

NOTE

If the battery is disconnected, the unit setting
is erased from memory and is automatically
set to °C.

Changing the display language

E00523200715

The language of the multi-information dis-
play can be switched.

1. Press and hold the multi-information

2. Lightly press the multi-information me-

ter switch to select “LANGUAGE” (lan-
guage setting).

Type 1

Type 2

Multi-information display

5-22

OGAE18E1

Instruments and controls

3. Press and hold the multi-information

meter switch for about 2 seconds or
more to display “LANGUAGE” (lan-
guage setting).

4. Lightly press the multi-information me-

ter switch to select the desired language.

5. If you hold down the multi-information

meter switch for about 2 seconds or
more, the setting is changed to the selec-
ted language.

NOTE

The memory of the language setting is
erased if the battery is disconnected, and it
returns automatically to ENGLISH or RUS-
SIAN.

If “---” is selected in the language setting, a
warning message is not displayed when
there is a warning display or interrupt dis-
play.

Operation sound setting

E00523401714

You can turn off the operation sounds of the
multi-information meter switch and daytime
dipper button.

1. Press and hold the multi-information

2. Lightly press the multi-information me-

ter switch to select “ ” (operation sound
setting).

Type 1

Type 2

3. Press and hold the multi-information

meter switch for about 2 seconds or
more to switch in sequence from ON
(operation sound on) → OFF (operation
sound off) → ON (operation sound on).
The setting is changed to the selected
condition.

NOTE

The memory of the operation sound setting
is erased if the battery is disconnected, and it
returns automatically to ON (operation
sound on).

The operation sound setting only deactivates
the operation sound of the multi-information
meter switch and daytime dipper button. The
warning display and other sounds cannot be
deactivated.

Changing the time until “REST
REMINDER” is displayed

E00523501715

The time until the display appears can be
changed.

1. Press and hold the multi-information

Multi-information display

5-23

OGAE18E1

Instruments and controls

2. Lightly press the multi-information me-

ter switch to select “ALARM” (rest time
setting).

Type 1

Type 2

3. Press and hold the multi-information

meter switch for about 2 seconds or
more to display “ALARM” (rest time
setting).

Type 1

Type 2

4. Lightly press the multi-information me-

ter switch to select the time until the dis-
play.

5. Press and hold the multi-information

meter switch for about 2 seconds or
more, the setting is changed to the selec-
ted time.

NOTE

If the battery is disconnected, the unit setting
is erased from memory and is automatically
set to OFF.

The drive time is reset when the ignition
switch is turned off or the operation mode is
put in OFF.

Changing the turn-signal sound

E00529101407

It is possible to change the turn-signal sound.

1. Press and hold the multi-information

2. Lightly press the multi-information me-

ter switch to select

(changing the

turn-signal sound).

Type 1

Type 2

Multi-information display

5-24

OGAE18E1

Instruments and controls

3. Press and hold the multi-information

meter switch for about 2 seconds or
more to switch in sequence from 1 (turn-
signal sound 1) → 2 (turn-signal sound
2) → 1 (turn-signal sound 1).
The setting changes to the selected turn-
signal sound.

Changing the momentary fuel
consumption display (Type 2)

E00529200195

It is possible to change the bar graph setting
of the momentary fuel consumption display.

1. Press and hold the multi-information

2. Lightly press the multi-information me-

ter switch to select

(changing the

momentary fuel consumption display)

3. Press and hold the multi-information

meter switch for about 2 seconds or
more to switch in sequence from ON
(with the green bar graph) → OFF (with-
out the green bar graph) → ON (with the
green bar graph).
The setting changes to the selected bar
graph setting.

Returning to the factory set-
tings

E00523601888

Many of the function settings can be returned
to their factory settings.

1. Press and hold the multi-information

2. Lightly press the multi-information me-

ter switch to select “RESET” (returning
to the factory settings).

Type 1

Type 2

3. When you press and hold the multi-in-

formation meter switch for about 5 sec-
onds or more, the buzzer sounds and all
of the function settings are returned to
the factory settings.

Multi-information display

5-25

OGAE18E1

Instruments and controls

Была ли эта страница вам полезна?

Да!Нет

4 посетителя считают эту страницу полезной.

Mitsubishi ASX (2018 year). Manual — part 8

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.