Mitsubishi L200 (2018 year). Manual — part 4

Electric window control switch

E00302303161

Each door window opens or closes while the
corresponding switch is operated.

Driver’s switch
LHD

Driver’s switch
RHD

1- Driver’s door window
2- Front passenger’s door window
3- Rear left door window (Double cab)
4- Rear right door window (Double cab)
5- Lock switch

WARNING

Before operating the electric window con-
trol, make sure that nothing can get trap-
ped (head, hand, finger, etc.).

Never leave the vehicle without removing
the key.

Never leave a child (or other person who
might not be capable of safe operation of
the electric window control) in the vehicle
alone.

WARNING

The child may tamper with the switch at
the risk of its hands or head being trap-
ped in the window.

Driver’s switches

The driver’s switches can be used to operate
all door windows. A window can be opened
or closed by operating the corresponding
switch.
Press the switch down to open the window,
and pull up the switch to close it.
If the switch for the driver’s window is fully
pressed down/pulled up, the door window au-
tomatically opens/closes completely.
If you want to stop the window movement,
operate the switch lightly in the reverse direc-
tion.

Passenger’s switches

The passenger’s switches can be used to op-
erate the corresponding passenger’s door
windows.

Press the switch down for opening the win-
dow, and pull up the switch for closing it.

NOTE

Repeated operation with the engine stopped
will run down the battery. Operate the win-
dow switches only while the engine is run-
ning.

The rear door windows only open halfway.

Lock switch

E00303102361

When this switch is operated, the passenger’s
switches cannot be used to open or close the
door windows and the driver’s switch cannot
open or close any door windows other than
the driver’s door window.

Electric window control*

3-22

OKTE18E1

Locking and unlocking

To unlock, press it once again.

1- Lock
2- Unlock

WARNING

A child may tamper with the switch at the
risk of its hands or head being trapped in
the window. When driving with a child in
the vehicle, please press the window lock
switch to disable the passenger’s switches.

Timer function

E00302402080

The door windows can be opened or closed
for 30 seconds after the engine is stopped.
However, once the driver’s door or the front
passenger’s door is opened, the windows can-
not be operated.

Safety mechanism (driver’s

window only)

E00302502108

When the door window is automatically
closed by pulling up the switch fully, if a
hand or head is trapped in the closing win-
dow, it will lower automatically.
Nonetheless, make sure that nobody puts
their head or hand out of the window when
closing the driver’s door window.
The lowered window will become operation-
al after a few seconds.

WARNING

If the battery terminals are disconnected
or the fuse for electric window is replaced,
the safety mechanism will be cancelled.
If a hand or head got trapped, a serious
injury could result.

CAUTION

The safety mechanism is cancelled just be-
fore the window is fully closed. This allows
the window to close completely. Therefore
be especially careful that no fingers are trap-
ped in the window.

The safety mechanism is deactivated while
the switch is pulled up. Therefore be espe-
cially careful that fingers are not trapped in
the door window opening.

NOTE

The safety mechanism can be activated if the
driving conditions or other circumstances
cause the driver’s door window to be subjec-
ted to a physical shock similar to that caused
by a trapped hand or head.

If the safety mechanism is activated five or
more times in a row, the safety mechanism
will be cancelled and the door window will
not close correctly.
In such a case, the following procedure
should be implemented to rectify this situa-
tion. If the window is open, repeatedly raise
the driver’s door window switch until that
window has been fully closed. Following
this, release the switch, raise the switch once
again and hold it in this condition for at least
1 second, then release it. You should now be
able to operate in the normal fashion.

If the battery terminals are disconnected or
the fuse for electric window is replaced, the
safety mechanism will be cancelled and the
door window will not automatically open/
close completely.
If the window is open, repeatedly raise the
driver’s door window switch until the win-
dow has been fully closed. Following this,
release the switch, raise the switch once
again and hold it in this condition for at least
1 second, then release it. You should now be
able to operate the driver’s door window in
the normal fashion.

Electric window control*

3-23

OKTE18E1

Locking and unlocking

OKTE18E1

Seat and seat belts

OKTE18E1

Seat adjustment

E00400301887

Adjust the driver’s seat so that you are com-
fortable and that you can reach the pedals,
steering wheel, switches etc. while retaining
a clear field of vision.

WARNING

Do not attempt to adjust the seat while
driving. This can cause loss of vehicle con-
trol and result in an accident. After ad-
justments are made, ensure the seating is
locked in position by attempting to move
the seat forward and rearward without
using the adjusting mechanism.

It is extremely dangerous to ride in the
cargo area (inside or outside) of a vehicle.
Also, the cargo area and rear seats should
never be used as a play area by children.
In a collision, people or children riding
unrestrained in these areas are more like-
ly to be seriously injured or killed.

Do not allow people or children to ride in
any area of your vehicle that is not equip-
ped with seats and seat belts, and make
sure that everyone travelling in your vehi-
cle is in a seat and wearing a seat belt, or
in the case of a child is strapped in a child
restraint.

WARNING

To minimize the risk of personal injury in
the event of a collision or sudden braking,
the seatbacks should always be in the al-
most upright position while the vehicle is
in motion. The protection provided by the
seat belts may be reduced significantly
when the seatback is reclined. There is
greater risk that the passenger will slide
under the seat belt, resulting in serious in-
jury, when the seatback is reclined.

Do not place objects under the seats. This
could prevent the seat from locking se-
curely, and it could lead to an accident. It
may also cause damage to the seat or oth-
er parts.

CAUTION

Make sure the seat is adjusted by an adult or
with adult supervision for correct and safe
operation.

Do not place a cushion or the like between
your back and the seatback while driving.
The effectiveness of the head restraints will
be reduced in the event of an accident.

The reclining mechanism of the front man-
ual seat’s seatback is spring loaded, causing
it to fold the seatback forward when the lock
lever is operated. When using the lever, sit
close to the seatback or hold it with your
hand to control its return motion.

When sliding the seats, be careful not to
catch your hand or foot.

CAUTION

If your vehicle is equipped with the rear
seat, when sliding or reclining the seat rear-
ward, pay careful attention to the rear seat
passengers. (Club cab and Double cab)

Front seats

E00400401468

Manual type*

1- To adjust forward or backward

Lift the handle and adjust the seat to the
desired position, and release the handle.

2- To recline the seatback

Pull the lever up and then lean backward
to the desired position, and release the
lever.

Seat adjustment

4-02

OKTE18E1

Seat and seat belts

3- To adjust seat cushion height (driver’s

side only of Club cab and Double cab)
Turn the dial and adjust the seat cushion
height to the desired position.

Power type*

1- To adjust forward or backward

Operate the switch as indicated by the
arrows and adjust the seat to the desired
position.

2- To recline the seatback

Operate the switch as indicated by the
arrows and adjust the seatback angle to
the desired position.

3- To adjust seat height

Operate the switch as indicated by the
arrows and adjust the seat height to the
desired position.
If the entire switch is operated, then the
entire seat moves.

4- To adjust seat cushion angle

Operate the switch as indicated by the
arrows and adjust the seat cushion angle
to the desired position.

NOTE

To prevent the battery from running down,
operate the switch with the engine running.

Heated seats*

E00401102254

The heated seats can be operated with the ig-
nition switch or the operation mode in ON.
Operate the switch as indicated by arrows.
The indication lamp (A) will illuminate while
the heater is on.

1 (HI)

Heater high (for quick heating).

Heater off.

3 (LO)

Heater low (to keep the seat
warm).

CAUTION

Operate in the high position for quick heat-
ing. Once the seat is warm, set the heater to
low to keep it warm. Slight variations in seat
temperature may be felt while using the
heated seats. This is caused by the operation
of the heater’s internal thermostat and does
not indicate a malfunction.

If the following types of persons use the
heated seats, they might become too hot or
receive minor burns (red skin, heat blisters,
etc.):

•

Children, elderly or ill people

•

People with sensitive skin

•

Excessively tired people

•

People under the influence of alcohol or
sleep inducing medication (cold medicine,
etc.)

Do not place heavy objects on the seat or
stick pins, needles, or other pointed objects
into it.

Do not use a blanket, cushion, or other mate-
rial with high heat insulation properties on
the seat while using the heater; this might
cause the heater element to overheat

Do not use benzine, kerosene, petrol, alcohol
or other organic solvents when cleaning the
seats. Doing so could damage not only the
seat cover, but also the heater element.

Front seats

4-03

OKTE18E1

Seat and seat belts

CAUTION

If water or any other liquid is spilled on the
seat, allow it to dry thoroughly before at-
tempting to use the heater.

Turn the heater off immediately if it appears
to be malfunctioning during use.

Rear seat (Club cab and
Double cab)*

E00401301536

When a person is sitting in the middle seating
position of the rear seat, adjust the head re-
straint to height at which it lock in position.
Refer to “Head restraints*” on page 4-05.
(Double cab)

Folding the seatback forward

(Double cab)

E00401601467

Pull up the band on the top of the seatback
and fold it forward.

To return

E00415600041

Raise the seatback until it is locked securely
in place.
Push and pull the seatback lightly to be sure
it is secure.

Folding up the seat cushion

(Club cab)*

E00411301063

The right and left seat cushions can be folded
up separately.
To fold the seat cushions up, raise the seat
cushions.

Securely retain the seat cushion by hooking
the retaining band (A) onto the head restraint
(B) of the rear seat.

Armrest (Double cab)

E00401701804

To use the armrest, fold it down.
To return to the original position, push it
backward (into the seatback) until it is level
with the seat. (Double cab)

Rear seat (Club cab and Double cab)*

4-04

OKTE18E1

Seat and seat belts

NOTE

Do not climb or sit on the armrest. Doing so
could damage the armrest.

The top surface of the armrest contains a cup
holder for rear seat occupants.
Refer to “Cup holder” on page 7-106.

Head restraints*

E00403302869

WARNING

Driving without the head restraints in
place can cause you and your passengers
serious injury or death in an accident. To
reduce the risk of injury in an accident,
always make sure the head restraints are
installed and properly positioned when
the seat is occupied.

Never place a cushion or similar device on
the seatback. This can adversely affect
head restraint performance by increasing
the distance between your head and the
restraint.

To adjust height

Front seats

Adjust the head restraint height so that the
centre of the head restraint is as close as pos-
sible to ear level to reduce the chances of in-
jury in the event of collision. Any person too
tall for the head restraint to reach their seated
ear level, should adjust the restraint as high
as possible.
To raise the head restraint, move it upward.
To lower the restraint, move it downward
while pushing the height adjusting knob (A)
in the direction of the arrow. After adjust-
ment, push the head restraint downward and
make sure that it is locked.

Rear centre seat

To reduce the risk of injury in an accident,
pull up the head restraint to the locked posi-
tion.

To raise the head restraint, move it upward.
To lower the restraint, move it downward
while pushing the height adjusting knob (A)
in the direction of the arrow. After adjust-
ment, push the head restraint downward and
make sure that it is locked.

Head restraints*

4-05

OKTE18E1

Seat and seat belts

WARNING

When a person sits in the middle seating
position of the rear seat, pull up the head
restraint to a height at which it locks in
position. Be sure to make this adjustment
before starting to drive. Serious injuries
could otherwise be suffered as the result
of an impact. (Double cab)

NOTE

The head restraint height of the outer seat in
the rear seat cannot be adjusted.

To remove

Lift the head restraint with the height adjust-
ing knob (A) pushed in.

To install

Confirm that the head restraint is facing the
correct direction, and then insert it into the
seatback while pressing the height adjusting
knob (A) in the direction indicated by the ar-
row.
The head restraint stalk with the adjustment
notches (B) must be installed in the hole with
the adjusting knob (A) (except head restraints
of the outer seat).

CAUTION

Confirm that the height adjusting knob (A)
is correctly adjusted as shown in the illustra-
tion, and also lift the head restraints to en-
sure that they do not come out of the seat-
back.

CAUTION

The shape and size of the head restraint dif-
fers according to the seat. Always use the
correct head restraint provided for the seat
and do not install the head restraint in the
wrong direction.

Head restraints*

4-06

OKTE18E1

Seat and seat belts

Seat belts

E00404802089

To protect you and your passengers in the
event of an accident, it is most important that
the seat belts are worn correctly while driv-
ing.
The front seat belts each have a pretensioner
system. (Single cab and Club cab)
The front seat belts and the rear outer seat
belts each have a pretensioner system. (Dou-
ble cab)
These belts are used the same way as a con-
ventional seat belt.
Refer to “Seat belt pretensioner system and
force limiter system*” on page 4-10.

WARNING

Seat belts should always be worn by every
adult who drives or rides in this vehicle,
and by all children who are tall enough to
wear seat belts properly.
Other children should always use proper
child restraint systems.

Always place the shoulder belt over your
shoulder and across your chest. Never put
it behind you or under your arm.

One seat belt should be used by only one
person. Doing otherwise can be danger-
ous.

WARNING

The seat belt will provide its wearer with
maximum protection if the recliner seat-
back is placed in fully upright position.
When the seatback is reclined, there is
greater risk that the passenger will slide
under the belt, especially in a forward im-
pact accident, and may be injured by the
belt or by striking the instrument panel or
seatbacks.

Remove any twists when using the belt.

No modifications or additions should be
made by the user which will either pre-
vent the seat belt adjusting devices from
operating to remove slack, or prevent the
seat belt assembly from being adjusted to
remove slack.

Never hold a child in your arms or on
your lap when riding in this vehicle, even
if you are wearing your seat belt. To do so
risks severe or fatal injury to the child in
a collision or sudden stop.

Always adjust the seat belt to a snug fit.

Always wear the lap portion of the belt
over your hips.

3-point type seat belt (with

emergency locking mechanism)

E00404902888

This type of belt requires no length adjust-
ment. Once worn, the belt adjusts itself to the
movement of the wearer, but in the event of a
sudden or strong shock, the belt automatical-
ly locks to hold the wearer’s body.

NOTE

You can check if the belt locks by pulling it
forward quickly.

To fasten

1. Pull the seat belt out slowly while hold-

ing the latch plate.

NOTE

When the seat belts cannot be pulled out in a
locked condition, pull the belts once force-
fully and then return them. After that, pull
the belts out slowly once again.

2. Insert the latch plate into the buckle until

a “click” is heard.

Seat belts

4-07

OKTE18E1

Seat and seat belts

WARNING

Never wear the lap portion of the belt
across your abdomen. During accidents it
can press sharply against the abdomen
and increase the risk of injury.

The seat belts must not be twisted when
worn.

3. Pull the belt slightly to adjust slackness

as desired.

To unfasten

Hold the latch plate and push the button on
the buckle.

NOTE

As the belt retracts automatically, keep hold-
ing the latch plate while retracting so that the
belt stows slowly. Failure to do this could
damage the vehicle.

NOTE

If the seat belt (A) or ring (B) becomes dirty,
the belt may not retract smoothly. If the seat
belt and ring are dirty, clean them with a
mild soap or detergent solution.

Seat belt reminder

E00409802361

For the driver and the front

passenger’s seat*

For the driver

For the front passenger

Type 1

Type 2

This warning lamp shows the case
of the left-hand drive vehicles.

If the ignition switch is turned to the “ON”
position or the operation mode is put in ON
while the driver’s and/or the front passen-
ger’s (if so equipped) seat belt is not fas-
tened, the warning lamp comes on and the
tone sounds for approximately 6 seconds to
remind the driver and/or the front passenger
(if so equipped) to fasten the seat belt.
If the vehicle is driven with the seat belt still
unfastened, the warning lamp will blink and
the tone will sound intermittently until the
seat belt is fastened.

WARNING

Do not install any accessory or sticker
that makes the lamp difficult to see.

NOTE

If the seat belt subsequently remains unfas-
tened, the warning lamp and the tone will is-
sue further warnings each time the vehicle
starts moving from a stop.

For the front passenger seat, the warning
function works only while a person is sitting
on the seat. (Club cab and Double cab)

Seat belts

4-08

OKTE18E1

Seat and seat belts

NOTE

When luggage is placed on the front passen-
ger seat, a sensor in the seat cushion may,
depending on the weight and position of the
luggage, cause the warning tone to sound
and the warning lamp to come on. (Club cab
and Double cab)

For the rear passenger’s seats*

E00415501047

This warning lamp shows the
case of the 5-passenger vehicles.

If the ignition switch is turned to the “ON”
position or the operation mode is put in ON
while a seat belt is not fastened, the warning
lamp comes on for approximately 30 seconds
to remind the rear passenger to fasten the seat
belt.

If the vehicle is driven with the seat belt still
unfastened, the warning lamps come on for
approximately another 30 seconds. (This illu-
mination happens only the first time the vehi-
cle starts moving with the seat belt still un-
fastened.)
The warning lamps go off when the seat belt
is fastened.

WARNING

Do not install any accessory or sticker
that makes the lamp difficult to see.

NOTE

The warning lamp comes on even if no one
is sitting on the rear seats.

If a seat belt is unfastened while the vehicle
is being driven, the tone sounds for approxi-
mately 1 second and the warning lamp
comes on for approximately 30 seconds. At
the same time, the warning lamp for the seat
where the seat belt is not fastened comes on.

If the seat belts are initially fastened but a
seat belt is unfastened while the vehicle is
stationary and the vehicle is then driven with
the seat belt still unfastened, the warning
lamp comes on again for approximately 30
seconds.

Adjustable seat belt anchor

(front seats of Club cab and

Double cab)

E00405001720

The seat belt anchor height can be adjusted.
To move the anchor, pull the lock knob (A)
and slide the anchor to the desired position.
Release the lock knob to lock the anchor into
position.

WARNING

When adjusting the seat belt anchor, set it
at a position that is sufficiently high so
that the belt will make full contact with
your shoulder but will not touch your
neck.

Seat belts

4-09

OKTE18E1

Seat and seat belts

Pregnant women restraint

E00405600064

WARNING

Seat belts work for everyone, including
pregnant women. Pregnant women should
use the available seat belts. This will re-
duce the likelihood of injury to both the
woman and the unborn child. The lap belt
should be worn across the thighs and as
snug against the hips as possible, but not
across the waist. Consult your doctor if
you have any additional questions or con-
cerns.

Seat belt pretensioner
system and force limiter
system*

E00405701567

The front seat belts each have a pretensioner
system and force limiter system. (Single cab
and Club cab)
The front seat belts and the rear outer seat
belts each have a pretensioner system and
force limiter system. (Double cab)

Pretensioner system

E00405802464

When the ignition switch or the operation
mode is under the following conditions, if
there is a frontal impact or a side impact (ve-
hicles equipped with SRS side airbags and
SRS curtain airbags) severe enough to injure
the driver and/or front passenger or when a
rollover or overturning of the vehicle is de-
tected (if so equipped), the pretensioner sys-
tem will retract the respective seat belts in-
stantaneously, thus maximizing the seat
belt’s effectiveness.
[Except for vehicles equipped with keyless
operation system]
The ignition switch is in the “ON” or
“START” position.
[Vehicles equipped with keyless operation
system]
The operation mode is in ON.

WARNING

To obtain the best results from your pre-
tensioner seat belt, make sure you have
adjusted your seat correctly and wear
your seat belt properly.

CAUTION

Installation of audio equipment or repairs in
the vicinity of the pretensioner seat belts or
floor console must be performed in line with
MITSUBISHI MOTORS guidelines. It is
important to do so because the work could
affect the pretensioner systems.

If you need to scrap the vehicle, please con-
sult a MITSUBISHI MOTORS Authorized
Service Point. It is important to do so be-
cause unexpected activation of the preten-
sioner seat belts could cause injuries.

NOTE

The pretensioner seat belts will be activated
if the vehicle suffers a severe impact, even if
the seat belts are not worn.

The pretensioner seat belts are designed to
work only once. After the pretensioner seat
belts have been activated, we recommend
you to have them replaced by a
MITSUBISHI MOTORS Authorized Serv-
ice Point.

SRS warning lamp

E00405901413

This warning lamp is shared by the SRS air-
bags and the pretensioner seat belts.
Refer to “SRS warning lamp” on page 4-34.

Pregnant women restraint

4-10

OKTE18E1

Seat and seat belts

Force limiter system

E00406001280

In the event of a collision, each force limiter
system will effectively absorb the load ap-
plied to the seat belt so as to minimize the
impact to the passenger.

Child restraint

E00406403552

When transporting children in your vehicle,
some type of child restraint system should al-
ways be used according to the size of the
child. This is required by law in most coun-
tries.
The regulations concerning driving with chil-
dren in the front seat may differ from country
to country. You are advised to comply with
the relevant regulations.

WARNING

When possible, put children in the rear
seat. Accident statistics indicate that chil-
dren of all sizes and ages are safer when
properly restrained in the rear seat rather
than in the front seat.

Holding a child in your arms is no substi-
tute for a restraint system. Failure to use
a proper restraint system can result in se-
vere or fatal injury to the child.

Each child restraint device or fixing is to
be used only by one child.

WARNING

When attaching a child restraint system
to the rear seat, adjust the front seat to
prevent the front seatbacks from touching
the child’s feet and child restraint system.
Otherwise, the child could be seriously in-
jured in the event of hard braking or a
collision.

Caution for installing the child

restraint on vehicles with a

front passenger airbag

E00406501810

The label shown here is attached on vehicles
with a front passenger airbag.

WARNING

Extreme Hazard!
NEVER use a rearward facing child re-
straint on a seat protected by an ACTIVE
AIRBAG in front of it, DEATH or SERI-
OUS INJURY to the CHILD can occur.

NOTE

The labels may be in different positions de-
pending on the vehicle model.

Use rearward facing child restraints in the
rear seat or turn off the front passenger’s air-
bag ON-OFF switch. (Club cab and Double
cab, refer to “To turn an airbag off (Club cab
and Double cab)” on page 4-27)

Front passenger's
airbag ON

Child restraint

4-11

OKTE18E1

Seat and seat belts

WARNING

A REARWARD FACING CHILD RE-
STRAINT must NOT be used in the front
passenger seat if the front passenger’s air-
bag has not been deactivated. The force of
an inflating airbag could kill or cause se-
rious injuries to the child. A rearward
facing child restraint should be used in
the rear seat.

A FORWARD FACING CHILD RE-
STRAINT should be used in the rear seat
whenever possible; if it must be used in
the front passenger seat, turn off the front
passenger’s airbag ON-OFF switch. Fail-
ure to do so could kill or cause serious in-
juries to the child.

Infants and small children

E00406602339

When transporting infants and small children
in your vehicle, follow the instruction given
below.

Instruction:

For small infants, an infant carrier
should be used. For small children
whose height when seated allows the
shoulder belt to lie in contact with the
face or the throat, a child seat should be
used.

The child restraint system should be ap-
propriate for the child’s weight and
height and properly fit in the vehicle.
For a higher degree of safety: THE
CHILD

RESTRAINT

SYSTEM

SHOULD BE INSTALLED IN THE
REAR SEAT.

Before purchasing a child restraint sys-
tem, try installing it in the seat to make
sure there is a good fit. Because of the
location of the seat belt buckles and the
shape of the seat cushion, it may be dif-
ficult to securely install some manufac-
turer’s child restraint systems.
If the child restraint system can be
pulled forward or to either side easily on
the seat cushion after the seat belt has
been tightened, choose another manufac-
turer’s child restraint system.

WARNING

When installing a child restraint system,
refer to the instructions provided by the
manufacturer of the restraint system.
Failure to do so can result in severe or fa-
tal injury to the child.

After installation, push and pull the child
restraint system back and forth, and side
to side, to see that it is properly secured.
If the child restraint system is not instal-
led securely, it may cause injury to the
child or other occupants in the case of ac-
cident or sudden stops.

When the child restraint system is not in
use, keep your child restraint system fixed
firmly or remove it from the vehicle in or-
der to prevent it from being thrown
around inside the vehicle during an acci-
dent.

NOTE

Depending on the seating position in the ve-
hicle and the child restraint system that you
have, the child restraint can be attached us-
ing one of the following two locations:

•

Using the lower anchorage in the rear seat
ONLY if the child restraint has ISOFIX
mountings (Double cab, See page 4-21).

•

Using the seat belt (See page 4-21).

Child restraint

4-12

OKTE18E1

Seat and seat belts

Older children

E00406701418

Children who have outgrown the child re-
straint system should be seated in the seat
and wear combination lap shoulder belt.
The lap portion of the belt should be snug
and positioned low on the abdomen so that it
is below the top of the hip-bone. Otherwise,
the belt could intrude into the child’s abdo-
men during an accident and cause injury.

Child restraint

4-13

OKTE18E1

Seat and seat belts

Была ли эта страница вам полезна?

Да!Нет

8 посетителей считают эту страницу полезной.

Mitsubishi L200 (2018 year). Manual — part 4

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.