KIA Ceed (2017 year). Manual — part 35
JD PE eng 7.QXP
03.01.2017
17:20 Page 69
Maintenance
Engine compartment main fuse panel (for gasoline engine MPI, GDI)
Fuse
Fuse rating
Symbol
Fuse Name
Protected component
POWER
80A
1
EPS Unit
STEERING
B+1
Inner Fuse Panel, IPS1 (H/LAMP HI LH,H/LAMP LOW LH, FRT TURN LH,
60A
B+1
POSITION LAMP LH), IPS2 (STATIC BENDING LAMP LH/RH, DRL LH/RH)
1
40A
ABS1
ESC Control Module, ABS Control Module
2
MULTI
40A
ABS2
ESC Control Module, ABS Control Module, Multipurpose Check Connector
FUSE
W/O Smart Key : Ignition Switch, START RELAY
40A
IG2
IG2
With Smart Key : IG2 RELAY, START RELAY
PTC
PTC
60A
PTC Relay (Gasoline)
HEATER
HEATER
Inner Fuse Panel, IPS3 (H/LAMP HI RH,H/LAMP LOW RH, FRT TURN RH,POSITION
B+2
60A
B+2
LAMP RH), IPS4 (FRT FOG LAMP LH/RH, REAR TURN LH/RH), IPS5 (REAR FOG LAMP,
INT TAIL LAMP)
40A
RR HTD
RR HTD RELAY , RR HTD
W/O Smart Key : Ignition Switch
40A
IG1
IG1
With Smart Key : IG1 RELAY, ACC RELAY,
INNER FUSE PANEL (FUSE No. - 8/13/21/23/28/29/35/36/37/38)
40A
DCT2
DCT2
TCU (DCT)
FUSE
1
30A
EPB1
Electric Parking Brake Module
2
30A
EPB2
Electric Parking Brake Module
40A
C/FAN
C/FAN LO RELAY, C/FAN HI RELAY
7
69
JD PE eng 7.QXP
03.01.2017
17:20 Page 70
Maintenance
Fuse
Fuse rating
Symbol
Fuse Name
Protected component
15A
DEICER
ICM Relay Box (Front Deicer Relay)
STOP
15A
LAMP
STOP LAMP
Stop signal electronic module
5
20A
TCU1
TCU
40A
DCT1
DCT1
TCU (DCT)
7
40A
EMS
EMS Box (FUSE No. - 1/2/3/4/5/6/7/8/9)
B+3
50A
B+3
Inner Fuse Panel (Leak Current Autocut Device, Fuse No. - 6/19/20/17/32/26/25)
FUSE
50A
BLOWER
BLOWER RELAY
10A
A/CON
A/C Control Module
10A
WIPER FRT
ECU, Rain Sensor
B/UP
10A
LAMP
B/UP LP
M/T : Back-up Lamp Switch, A/T : Transaxle Range Switch, TCU
4
15A
ECU4
Smart Key Control Module, Immobilizer Module, ECU
3
10A
ABS3
ESC Control Module, ABS Control Module, Yaw Rate Sensor, HAC, ESS RELAY
6
15A
TCU2
Transaxle Range Switch, TCU, Stop Lamp Switch
7 70
JD PE eng 7.QXP
03.01.2017
17:20 Page 71
Maintenance
Symbol
Relay Name
Type
Fuse rating
Symbol
Fuse Name
Relay Name
LO
COOLING FAN LOW RELAY
PLUG MICRO
15A
F/PUMP
F/PUMP
FUEL PUMP RELAY
HI
3
COOLING FAN HIGH RELAY
PLUG MICRO
15A
ECU3
ECU
BLOWER RELAY
PLUG MICRO
15A
HORN
Horn Relay
INJECTOR, ECU,
REAR DEFOGGER RELAY
PLUG MICRO
10A
INJECTOR
INJECTOR
FUEL PUMP RELAY
2
4 (IG2)
IG2 RELAY
PLUG MICRO
10A
ECU2
ECU
IGN
Ignition Coil #1/#2/#3/#4,
FRT WIPER RELAY
PLUG MICRO
20A
COIL
IGN COIL
Condenser
3 (IG1)
IG1 RELAY
PLUG MICRO
9
E/R Fuse & Relay Box
10A
SENSOR2
(COOLING LOW RELAY),
1
Oil Control Valve #1/#2
START RELAY
PLUG MICRO
1
20A
ECU1
ECU
2 (ACC)
ACC RELAY
PLUG MICRO
8
Oxygen Sensor (UP/DOWN),
GSL
10A
SENSOR1
Variable Intake Solenoid Valve,
PTC
PTC RELAY (GASOLINE)
PLUG MINI
Purge Control Solenoid Valve
HEATER
7 71
JD PE eng 7.QXP
03.01.2017
17:20 Page 72
Maintenance
Engine compartment main fuse panel (for gasoline engine T-GDI)
Fuse
Fuse rating
Symbol
Fuse Name
Protected component
POWER
80A
1
EPS Unit
STEERING
B+1
Inner Fuse Panel, IPS1 (H/LAMP HI LH,H/LAMP LOW LH, FRT TURN LH,
60A
B+1
POSITION LAMP LH), IPS2 (STATIC BENDING LAMP LH/RH, DRL LH/RH)
1
40A
ABS1
ESC Control Module, ABS Control Module
2
MULTI
40A
ABS2
ESC Control Module, ABS Control Module, Multipurpose Check Connector
FUSE
W/O Smart Key : Ignition Switch, START RELAY
40A
IG2
IG2
With Smart Key : IG2 RELAY, START RELAY
60A
C/FAN
C/FAN Relay
Inner Fuse Panel, IPS3 (H/LAMP HI RH,H/LAMP LOW RH, FRT TURN RH,
B+2
60A
B+2
POSITION LAMP RH), IPS4 (FRT FOG LAMP LH/RH, REAR TURN LH/RH),
IPS5 (REAR FOG LAMP, INT TAIL LAMP)
40A
RR HTD
RR HTD RELAY , RR HTD
W/O Smart Key : Ignition Switch
40A
IG1
IG1
With Smart Key : IG1 RELAY, ACC RELAY,
INNER FUSE PANEL (FUSE No. - 8/13/21/23/28/29/35/36/37/38)
PTC
PTC
50A
PTC Relay (Gasoline)
FUSE
HEATER
HEATER
1
30A
EPB1
Electric Parking Brake Module
2
30A
EPB2
Electric Parking Brake Module
VACUUM
VACUUM
30A
VACUUM PUMP
PUMP
PUMP
7
72
JD PE eng 7.QXP
03.01.2017
17:20 Page 73
Maintenance
Fuse
Fuse rating
Symbol
Fuse Name
Protected component
15A
DEICER
ICM Relay Box (Front Deicer Relay)
STOP
15A
LAMP
STOP LAMP
Stop signal electronic module
5
20A
TCU1
TCU
40A
DCT1
DCT1
TCU (DCT)
7
40A
EMS
EMS Box (FUSE No. - 1/2/3/4/5/6/7/8/9)
B+3
50A
B+3
Inner Fuse Panel (Leak Current Autocut Device, Fuse No. - 6/19/20/17/32/26/25)
FUSE
50A
BLOWER
BLOWER RELAY
10A
A/CON
A/C Control Module
10A
WIPER FRT
ECU, Rain Sensor
B/UP
10A
LAMP
B/UP LP
M/T : Back-up Lamp Switch, A/T : Transaxle Range Switch, TCU
4
15A
ECU4
Smart Key Control Module, Immobilizer Module, ECU
3
10A
ABS3
ESC Control Module, ABS Control Module, Yaw Rate Sensor, HAC, ESS RELAY
6
15A
TCU2
Transaxle Range Switch, TCU, Stop Lamp Switch
7 73
JD PE eng 7.QXP
03.01.2017
17:20 Page 74
Maintenance
Symbol
Relay Name
Type
Fuse rating
Symbol
Fuse Name
Relay Name
GSL
PTC
PTC RELAY (GASOLINE)
PLUG MICRO
15A
F/PUMP
F/PUMP
FUEL PUMP RELAY
HEATER
3
15A
ECU3
ECU
BLOWER RELAY
PLUG MICRO
15A
HORN
Horn Relay
REAR DEFOGGER RELAY
PLUG MICRO
INJECTOR, ECU,
4 (IG2)
10A
INJECTOR
INJECTOR
IG2 RELAY
PLUG MICRO
FUEL PUMP RELAY
2
10A
ECU2
ECU
FRT WIPER RELAY
PLUG MICRO
IGN
Ignition Coil #1/#2/#3/#4,
3 (IG1)
20A
COIL
IGN COIL
IG1 RELAY
PLUG MICRO
Condenser
1
9
E/R Fuse & Relay Box
START RELAY
PLUG MICRO
10A
SENSOR2
(COOLING LOW RELAY),
Oil Control Valve #1/#2
2 (ACC)
ACC RELAY
PLUG MICRO
1
20A
ECU1
ECU
COOLING FAN
PLUG MINI
8
Oxygen Sensor (UP/DOWN),
10A
SENSOR1
Variable Intake Solenoid Valve,
Purge Control Solenoid Valve
7 74
JD PE eng 7.QXP
03.01.2017
17:21 Page 75
Maintenance
Engine compartment main fuse panel (for diesel engine)
Fuse
Fuse rating
Symbol
Fuse Name
Protected component
POWER
80A
1
EPS Unit
STEERING
B+1
Inner Fuse Panel, IPS1 (H/LAMP HI LH,H/LAMP LOW LH, FRT TURN LH, POSITION LAMP LH),
60A
B+1
IPS2 (STATIC BENDING LAMP LH/RH, DRL LH/RH)
1
40A
ABS1
ESC Control Module, ABS Control Module
MULTI
2
FUSE
40A
ABS2
ESC Control Module, ABS Control Module, Multipurpose Check Connector
W/O Smart Key : Ignition Switch, START RELAY
40A
IG2
IG2
With Smart Key : IG2 RELAY, START RELAY, INNER FUSE PANEL (Fuse No. - 14/24/22/15/10)
B+2
Inner Fuse Panel, IPS3 (H/LAMP HI RH,H/LAMP LOW RH, FRT TURN RH,
60A
B+2
POSITION LAMP RH), IPS4 (FRT FOG LAMP LH/RH, REAR TURN LH/RH),
IPS5 (REAR FOG LAMP, INT TAIL LAMP)
40A
RR HTD
RR HTD RELAY , RR HTD
W/O Smart Key : Ignition Switch
40A
IG1
IG1
With Smart Key : IG1 RELAY, ACC RELAY, INNER FUSE PANEL (Fuse No. - 38/36/21/37/
23/29/28, Fuse No. - 13/8/35)
1
30A
EPB1
Electric Parking Brake Module
FUSE
2
30A
EPB2
Electric Parking Brake Module
50A
C/FAN
C/FAN LO RELAY, C/FAN HI RELAY
15A
DEICER
ICM Relay Box (Front Deicer Relay)
15A
STOP
STOP LAMP
Stop signal electronic module
LAMP
7
75
JD PE eng 7.QXP
03.01.2017
17:21 Page 76
Maintenance
Fuse
Fuse rating
Symbol
Fuse Name
Protected component
5
20A
TCU1
TCU
FUEL
40A
FUEL HEATER RELAY
HEATER
7
40A
EMS
EMS BOX (Fuse No. - 1/2/3/4/5/6/7/8/9)
B+3
50A
B+3
Inner Fuse Panel (Leak Current Autocut Device, Fuse No. - 6/19/20/17/32/26/25)
50A
BLOWER
BLOWER RELAY
FUSE
10A
A/CON
A/C Control Module
10A
WIPER FRT
ECU, Rain Sensor
B/UP
10A
LAMP
B/UP LP
M/T : Back-up Lamp Switch, A/T : Transaxle Range Switch, TCU
4
Smart Key Control Module, Immobilizer Module, ECU, Air Flow Sensor,
15A
ECU4
Fuel Water Sensor
3
10A
ABS3
ESC Control Module, ABS Control Module, Yaw Rate Sensor
6
15A
TCU2
Transaxle Range Switch, TCU
7 76
JD PE eng 7.QXP
03.01.2017
17:21 Page 77
Maintenance
Symbol
Relay Name
Type
Fuse rating
Symbol
Fuse Name
Relay Name
LO
COOLING FAN LOW RELAY
PLUG MICRO
15A
SPARE
SPARE
-
HI
COOLING FAN HIGH RELAY
PLUG MICRO
15A
HORN
HORN RELAY
2
Oil Level Sensor, Fuel
BLOWER RELAY
PLUG MICRO
10A
ECU2
Pressure Control Valve
REAR DEFOGGER RELAY
PLUG MICRO
20A
SPARE
SPARE
-
4 (IG2)
E/R Fuse & Relay Box
IG2 RELAY
PLUG MICRO
9
(COOLING FAN LOW RELAY),
10A
SENSOR2
Lambda Sensor (D4FB),
FRT WIPER RELAY
PLUG MICRO
Stop Lamp Switch
3 (IG1)
1
IG1 RELAY
PLUG MICRO
20A
ECU1
ECU
1
DSL Box (PTC1 RELAY,
START RELAY
PLUG MICRO
8
GLOW RELAY),
10A
SENSOR1
VGT Control Sensor,
2 (ACC)
ACC RELAY
PLUG MICRO
Camshaft Position Sensor,
Electrical EGR Valve
FUEL HEATER RELAY
PLUG MINI
7 77
JD PE eng 7.QXP
03.01.2017
17:21 Page 78
Maintenance
OGD071024
Engine compartment fuse panel
(Diesel engine only)
✽ NOTICE
The actual fuse/relay panel label may
differ from equipped items.
OJD075102L
Description
Fuse rating
Protected Component
80A
Glow Unit
PTC 1
50A
PTC 1 Relay, PTC HEATER
PTC 2
50A
PTC 2 Relay, PTC HEATER
PTC 3
50A
PTC 3 Relay, PTC HEATER
7 78
JD PE eng 7.QXP
03.01.2017
17:21 Page 79
Maintenance
LIGHT BULBS
✽ NOTICE
WARNING - Working on
CAUTION
After driving in heavy rain or washing
the lights
•
If you do not have necessary
the vehicle, headlight and taillight lenses
Prior to working on the light, firmly
tools, the correct bulbs and the
could appear foggy. This condition is
apply the parking brake, ensure
expertise, we recommend that
caused by the temperature difference
that the ignition switch is turned to
you consult an authorized Kia
between the lamp inside and outside.
the “LOCK” position (smart key:
dealer. In many cases, it is diffi-
This is similar to the condensation on
turn off the engine) and turn off the
cult to replace vehicle light bulbs
your windows inside your vehicle during
lights to avoid sudden movement
because other parts of the vehicle
rain and does not indicate a problem
of the vehicle and burning your fin-
must be removed before you can
with your vehicle. If the water leaks into
gers or getting an electric shock.
get to the bulb. This is especially
the lamp bulb circuitry, we recommend
true if you have to remove the
that the system be checked by an
headlight assembly to get to the
authorized Kia dealer.
Use only the bulbs of the specified
bulb(s).
wattage.
Removing/installing the headlight
assembly can result in damage to
CAUTION
the vehicle.
Be sure to replace the burned-out
•
Do not install additional bulb or
bulb with one of the same wattage
LED. If you install that, the lamp
may not be operated properly and
rating. Otherwise, it may cause
damage to the fuse or electric
fuse box or electric wiring system
wiring system.
may have problem.
7 79
JD PE eng 7.QXP
03.01.2017
17:21 Page 80
Maintenance
■ Type A
Front light replacement
(1) Front turn signal light
(2) Headlight (Low)
(3) Static bending light (if equipped)
(4) Position light
(5) Position light / Daytime running light
(DRL, LED Type) (if equipped)
(6) Headlight (High)
(7) Daytime running light (DRL, Bulb type)
OJD075052
(if equipped)
OJD072053
■ Type B
(8) Front fog light (if equipped)
Diesel only
1. Turn off the engine and open the hood.
2. Disconnect the negative battery cable.
3. Disconnect the power connector front
the back of the headlight assembly.
OJD075066
■ Type C
OJD072054
If you can reach the bulb without remov-
ing the headlight assembly, you do not
need to do step 4 to 7.
4. Loosen the retaining bolts on the front
bumper .
- Front bumper upper board : 4 EA
- Front bumper cover : 1 EA
OJD073081
7 80
JD PE eng 7.QXP
03.01.2017
17:22 Page 81
Maintenance
OJD075055
Diesel only
OJD072056
OJD072041
6. Loosen the retaining bolt .
Headlight (High, 1) and static bending
7. Pull out the headlight assembly from
light (2, if equipped)
the body of the vehicle.
Follow the steps 1 to 7 from the previous
chapter.
8. Remove the cover by turning it coun-
terclockwise.
9. Disconnect the headlight bulb socket-
connector.
10. Unsnap the headlight bulb retaining
OJD075062
wire by depressing the end and push-
5. Pull out the front bumper cover.
ing it upward.
11. Remove the bulb from the headlight
assembly.
12. Install a new headlight bulb and snap
the headlight bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
7 81
JD PE eng 7.QXP
03.01.2017
17:22 Page 82
Maintenance
13. Connect the headlight bulb socket
✽ NOTICE
connector.
We recommend that the headlight aim-
14. Install the headlight bulb cover by
ing be adjusted after an accident or
turning it clockwise.
after the headlight assembly is rein-
15. Connect the power connector to the
stalled at an authorized Kia dealer.
back of the headlight assembly.
Position light (3, bulb type)
Follow the steps 1 to 9 from the previous
page.
10. Pull out the socket from the assembly.
11. Pull the bulb out of the socket.
OJD072042
12. Insert a new bulb into the socket.
Headlight (Low, Non-HID Type)
13. Install the socket into the assembly.
Follow the steps 1 to 7 from the previous
14. Install the headlight bulb cover by
page.
turning it clockwise.
8. Remove the cover by turning it coun-
terclockwise.
9. Remove the socket from the assembly
by turning the socket counterclockwise
until the tabs on the socket align with
the slots on the assembly.
10. Pull the bulb out of the socket.
11. Insert a new bulb into the socket.
12. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
13. Install the headlight bulb cover by
turning it clockwise.
7 82
JD PE eng 7.QXP
03.01.2017
17:22 Page 83
Maintenance
Headlight (Low, HID type),
✽ NOTICE
Position light/DRL (LED type)
HID lamps have superior performance
If the light does not operate, we recom-
vs. halogen bulbs. HID lamps are esti-
mend that the system be checked by an
mated by the manufacturer to last twice
authorized Kia dealer.
as long or longer than halogen bulbs
depending on their frequency of use.
They will probably require replacement
WARNING - HID Headlight
at some point in the life of the vehicle.
low beam (if equipped)
Cycling the headlamps on and off more
Do not attempt to replace or
than typical use will shorten HID lamps
inspect the low beam (XENON bulb)
life. HID lamps do not fail in the same
due to electric shock danger. If the
manner as halogen incandescent lamps.
low beam (XENON bulb) is not
If a headlamp goes out after a period of
OHD076046
working, we recommend that the
operation but will immediately relight
system be checked by an author-
when the headlamp switch is cycled it is
WARNING - Halogen bulbs
ized Kia dealer.
likely the HID lamp needs to be replaced.
•
Halogen bulbs contain pressurized
HID lighting components are more com-
gas that will produce flying pieces
plex than conventional halogen bulbs
of glass if broken.
thus have higher replacement cost.
•
Always handle them carefully, and
avoid scratches and abrasions. If
❈ Traffic Change (For Europe)
the bulbs are lit, avoid contact with
The low beam light distribution is asym-
liquids. Never touch the glass with
metric. If you go abroad to a country with
bare hands. Residual oil may cause
opposite traffic direction, this asymmetric
the bulb to overheat and burst
part will dazzle oncoming car driver. To
when lit. A bulb should be operated
prevent dazzle, ECE regulation demand
only when installed in a headlight.
several technical solutions (ex. automatic
•
If a bulb is damaged or cracked,
change system, adhesive sheet, down
replace it immediately and carefully
aiming). This headlamps are designed
dispose of it.
not to dazzle opposite drivers. So, you
•
Wear eye protection when chang-
need not change your headlamps in a
ing a bulb. Allow the bulb to cool
country with opposite traffic direction.
down before handling it.
7
83
JD PE eng 7.QXP
03.01.2017
17:22 Page 84
Maintenance
11. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
OJD072044
OJD072050
Turn signal light
Front fog light, Daytime running light
Follow the steps 1 to 7 from the previous
(if equipped)
page.
1. Pull the wheel guard down by rotating
8. Remove the socket from the assembly
the screws.
by turning the socket counterclockwise
2. Reach your hand into the back of the
until the tabs on the socket align with
front bumper.
the slots on the assembly.
3. Disconnect the power connector from
9. Remove the bulb from the socket by
the socket.
pressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket. Pull
the bulb out of the socket.
10. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
7 84
JD PE eng 7.QXP
03.01.2017
17:22 Page 85
Maintenance
■ Fog light
■ DRL
4. With the head lamp and battery in nor-
mal condition, aim the head lamps so
the brightest portion falls on the hori-
zontal and vertical lines.
5. To aim the low beam left or right, turn
the driver
(1) clockwise or counter-
clockwise. To aim the low beam up or
down, turn the driver (2) clockwise or
■ Fog light+DRL (Bulb type)
counterclockwise.
To aim the high beam up or down, turn
the driver
(3) clockwise or counter-
clockwise.
OJD072027
Headlight and front fog light aim-
ing (for Europe)
Headlight aiming
Without AFLS
1. Inflate the tires to the specified pres-
sure and remove any loads from the
vehicle except the driver, spare tire,
OJD073067/OJD073068/OJD073069
and tools.
4. Remove the bulb-socket from the
2. The vehicle should be placed on a flat
housing by turning the socket counter
floor.
clockwise until the tabs on the socket
3. Draw vertical lines (Vertical lines pass-
align with the slots on the housing.
ing through respective head lamp cen-
5. Install the new bulb-socket into the
ters) and a horizontal line (Horizontal
housing by aligning the tabs on the
line passing through center of head
socket with the slots in the housing.
lamps) on the screen.
Push the socket into the housing and
turn the socket clockwise.
6. Connect the power connector to the
socket.
7
85
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст