KIA Ceed (2017 year). Manual — part 26
Driving your vehicle
Emergency Stop Signal (ESS)
Good braking practices
•
Check to be sure the parking brake is
not engaged and that the parking
The Emergency Stop Signal system
brake indicator light is out before driv-
alerts the driver behind by blinking the
WARNING
ing away.
stop light when the vehicle is braked rap-
•
Whenever you leave or park your
•
Driving through water may get the
idly and severely.
vehicle, always set the parking
brakes wet. They can also get wet
The system is activated when:
brake as far as possible and fully
when the vehicle is washed. Wet
• The vehicle suddenly stops
(vehicle
engage the vehicle's transaxle
brakes can be dangerous! Your vehicle
speed is over 55km/h and the vehicle
into the P (Park) position. If the
will not stop as quickly if the brakes are
deceleration at greater than 7 m/s2)
parking brake is not fully
wet. Wet brakes may cause the vehicle
• The ABS is activating
engaged, the vehicle may move
to pull to one side.
When the vehicle speed is under 40 km/h
inadvertently and injure yourself
To dry the brakes, apply the brakes
and the ABS deactivates or the sudden
and others.
lightly until the braking action returns to
stop situation is over, the stop light blink-
•
All vehicles should always have
normal, taking care to keep the vehicle
ing will stop. Instead, the hazard warning
the parking brake fully engaged
under control at all times. If the braking
flasher will turn on automatically.
when parking to avoid inadver-
action does not return to normal, stop
The hazard warning flasher will turn off
tent movement of the vehicle
as soon as it is safe to do so and we
when vehicle speed is over 10km/h after
which can injure occupants or
recommend that you call an authorized
the vehicle has stopped. Also, it will turn
pedestrians.
Kia dealer.
off when the vehicle is driven at low
•
Do not coast down hills with the vehicle
speed for some time. You can turn it off
out of gear. This is extremely haz-
manually by pushing the hazard warning
ardous. Keep the vehicle in gear at all
flasher switch.
times, use the brakes to slow down,
then shift to a lower gear so that
engine braking will help you maintain a
CAUTION
safe speed.
The Emergency Stop Signal (ESS)
system will not work if the hazard
warning flasher is already on.
5 56
Driving your vehicle
•
Do not "ride" the brake pedal. Resting
•
Be cautious when parking on a hill.
•
Do not hold the vehicle on the upgrade
your foot on the brake pedal while driv-
Firmly engage the parking brake and
with the accelerator pedal. This can
ing can be dangerous because it can
place the shift lever in P
(automatic
cause the transaxle to overheat.
result in the brakes overheating and
transaxle) or in first or reverse gear
Always use the brake pedal or parking
losing their effectiveness. It also
(manual transaxle). If your vehicle is
brake.
increases the wear of the brake com-
facing downhill, turn the front wheels
ponents.
into the curb to help keep the vehicle
•
If a tire goes flat while you are driving,
from rolling. If your vehicle is facing
apply the brakes gently and keep the
uphill, turn the front wheels away from
vehicle pointed straight ahead while
the curb to help keep the vehicle from
you slow down. When you are moving
rolling. If there is no curb or if it is
slowly enough for it to be safe to do so,
required by other conditions to keep the
pull off the road and stop in a safe
vehicle from rolling, block the wheels.
place.
•
Under some conditions your parking
•
If your vehicle is equipped with an
brake can freeze in the engaged posi-
automatic transaxle, do not let your
tion. This is most likely to happen when
vehicle creep forward. To avoid creep-
there is an accumulation of snow or ice
ing forward, keep your foot firmly on
around or near the rear brakes or if the
the brake pedal when the vehicle is
brakes are wet. If there is a risk that the
stopped.
parking brake may freeze, apply it only
temporarily while you put the shift
lever in P (automatic transaxle) or in
first or reverse gear (manual transaxle)
and block the rear wheels so the vehi-
cle cannot roll. Then release the park-
ing brake.
5 57
Driving your vehicle
CRUISE CONTROL SYSTEM (IF EQUIPPED)
■ Normal vision
This system is designed to function
above approximately 30 km/h (20 mph).
CAUTION
During cruise-speed driving of a
manual transaxle vehicle, do not
WARNING
shift into neutral without depress-
•
If the cruise control is left on,
ing the clutch pedal, since the
(cruise indicator light is illuminat-
engine will be overrevved. If this
ed), the cruise control can be
happens, depress the clutch pedal
switched on accidentally. Keep
or release the cruise control ON-
the cruise control system off
OFF switch.
when the cruise control is not in
use, to avoid inadvertently set-
ting a speed.
✽ NOTICE
■ Supervision
•
Use the cruise control system
•
During normal cruise control opera-
only when traveling on open
tion, when the SET switch is activated
highways in good weather.
or reactivated after applying the
•
Do not use the cruise control
brakes, the cruise control will ener-
when it may not be safe to keep
gize after approximately
3 seconds.
the vehicle at a constant speed,
This delay is normal.
for instance, driving in heavy or
•
To activate cruise control, depress the
varying traffic, or on slippery
brake pedal at least once after turning
(rainy, icy or snow-covered) or
the ignition switch to the ON position
winding roads or over 6% up-hill
or starting the engine. This is to check
or down-hill roads.
if the brake switch which is important
•
Pay particular attention to the
part to cancel cruise control is in nor-
driving conditions whenever
mal condition.
OJD052015/OJD055048L
using the cruise control system.
1. Cruise indicator
•
Be careful when driving downhill
2. Cruise set indicator
using the cruise control system,
which may increase the vehicle
The cruise control system allows you to
speed.
program the vehicle to maintain a con-
stant speed without pressing the acceler-
ator pedal.
5
58
Driving your vehicle
OJD053016
OJD053017
OJD053018
Cruise control switch
To set cruise control speed:
3. Move the lever down (to SET-), and
release it at the desired speed. The
O: Cancels cruise control operation.
1. Move the lever down (
) on the
cruise set indicator light will illuminate.
: Turns cruise control system on or
steering wheel, to turn the system on.
Release the accelerator pedal at the
off.
The cruise indicator light will illumi-
same time. The desired speed will
RES+: Resumes or increases cruise
nate.
automatically be maintained.
control speed.
2. Accelerate to the desired speed, which
On a steep grade, the vehicle may slow
SET-: Sets or decreases cruise control
must be more than 30 km/h (20 mph).
down or speed up slightly while going
speed.
downhill.
✽ NOTICE - Manual transaxle
For manual transaxle vehicles, you
should depress the brake pedal at least
once to set the cruise control after start-
ing the engine.
5 59
Driving your vehicle
To temporarily accelerate with the
cruise control on:
If you want to speed up temporarily when
the cruise control is on, depress the
accelerator pedal. Increased speed will
not interfere with cruise control operation
or change the set speed.
To return to the set speed, take your foot
off the accelerator pedal.
OJD053019
OJD053018
To increase cruise control set
To decrease the cruising speed:
speed:
Follow either of these procedures:
Follow either of these procedures:
• Move the lever down (to SET-) and
• Move the lever up (to RES+) and hold
hold it. Your vehicle will gradually slow
it. Your vehicle will accelerate. Release
down. Release the lever at the speed
the lever at the speed you want.
you want to maintain.
• Move the lever up
(to RES+) and
• Move the lever down
(to SET-) and
release it immediately. The cruising
release it immediately. The cruising
speed will increase by 2 km/h (1 mph)
speed will decrease by 2 km/h (1 mph)
each time you move the lever up (to
each time you move the lever down (to
RES+) in this manner.
SET-) in this manner.
5 60
Driving your vehicle
Each of these actions will cancel cruise
control operation (the cruise set indicator
light will go off), but it will not turn the
system off. If you wish to resume cruise
control operation, move up the lever (to
RES+) located on your steering wheel.
You will return to your previously preset
speed.
OJD053020
OJD053019
To cancel cruise control, do one
To resume cruising speed at
of the following:
more than approximately 30 km/h
• Depress the brake pedal.
(20 mph):
• Depress the clutch pedal if equipped
If any method other than the
button
with a manual transaxle.
was used to cancel cruising speed and
• Shift into N (Neutral) if equipped with
the system is still activated, the most
an automatic transaxle.
recent set speed will automatically
resume when the
+RES switch is
• Press the O (Cancel) button located on
pushed.
the steering wheel.
It will not resume, however, if the vehicle
• Decrease the vehicle speed lower than
speed has dropped below approximately
the memory speed by 20 km/h (12
30 km/h (20 mph).
mph).
• Decrease the vehicle speed to less
than approximately 30 km/h (20 mph).
5 61
Driving your vehicle
To turn cruise control off, do one
of the following:
• Move the lever down (
).
• Move the lever up (
). (If you move
the lever up, the speed limit system will
turn on)
• Turn the ignition off.
Both of these actions cancel cruise con-
trol operation. If you want to resume
cruise control operation, repeat the steps
provided in “To set cruise control speed”
on the previous page.
5 62
Driving your vehicle
SPEED LIMIT CONTROL SYSTEM (IF EQUIPPED)
You can set the speed limit when you do
not want to drive over a specific speed.
If you drive over the preset speed limit,
the warning system operates (set speed
limit will blink and chime will sound) until
the vehicle speed returns within the
speed limit.
✽ NOTICE
While speed limit control is in opera-
tion, the cruise control system cannot be
activated.
OJD053016
OJD053021
Speed limit control switch
To set speed limit :
O: Cancels set speed limit.
1. Move the lever up (
) on the steer-
: Turns speed limit control system on
ing wheel, to turn the system on.
or off.
RES+: Resumes or increases speed limit
control speed.
SET-: Sets or decreases speed limit con-
trol speed.
5 63
Driving your vehicle
■ Normal vision
■ Supervision
■ Normal vision
■ Supervision
OJD052031/OJD055034L
OJD053022
OJD052032/OJD055044L
The speed limit indicator light will illumi-
2. Move the lever down (to SET-).
The set speed limit will be displayed.
nate.
3. Move the lever up (to RES+) or down
(to SET-), and release it at the desired
speed. Move the lever up (to RES+) or
down (to SET-) and hold it. The speed
will increase or decrease by 5 km/h (3
mph).
Move the lever up (to RES+) or down
(SET-) and release it immediately. The
speed will increase or decrease by 1
km/h.
The set speed limit will display on the
instrument cluster.
5 64
Driving your vehicle
To drive over the preset speed limit you
■ Normal vision
■ Supervision
must depress hard on the accelerator
pedal
(more than approximately
80%)
until the kick down mechanism works
with a clicking noise. Then the set speed
limit will blink and chime will sound until
you return the vehicle speed within the
speed limit.
✽ NOTICE
• Depressing the accelerator pedal less
than approximately 50%, the vehicle
OJD053023
OJD052033/OJD055046L
will not speed over the preset speed
limit but maintain the vehicle speed
To turn off the speed limit con-
within the speed limit.
trol, do one of the following:
CAUTION
• Aclicking noise heard from the kick
The “---” indicator will blink if there
• Move the lever up (
).
down mechanism by depressing the
is a problem with speed limit con-
• Move the lever down
(
).
(If you
accelerator pedal fully is a normal
trol system.
condition.
move the lever down, the cruise sys-
If this occurs, we recommend that
tem will turn on)
the system be checked by an
• Turn the ignition off.
authorized Kia dealer.
If you press the O
(CANCEL) button
once, the set speed limit will cancel, but
it will not turn the system off. If you wish
to reset the speed limit, move the lever
up (to RES+) or down (to SET-) on your
steering wheel to your desired speed.
5 65
Driving your vehicle
LANE DEPARTURE WARNING SYSTEM (LDWS) (IF EQUIPPED)
WARNING
•
The LDWS does not make the vehi-
cle change lanes. It is the driver's
responsibility to always check the
road conditions.
•
Do not turn the steering wheel sud-
denly, when the LDWS warns you
that your vehicle is leaving the lane.
OJD055028
•
If the sensor can not detect the lane
or if the vehicle speed does not
exceed 60km/h, the LDWS won't
warn you even though the vehicle
OJD045178L
leaves the lane.
To operate the LDWS, press the switch
•
If your vehicle has window tint or
with the ignition in the ON position. The
other types of coating on the front
indicator illuminates on the cluster. To
windshield, the LDWS may not
cancel the LDWS, press the switch
work properly.
again.
•
Do not let water or any kind of liq-
OJD052029
uid come in contact with the LDWS
sensor.
•
Do not remove the LDWS parts and
do not affect the sensor by a strong
impact.
•
Do not put objects that reflect light
on the dash board.
•
Always check road conditions
because you may not hear the
warning chime because of audio
OJD052030
and external conditions.
This system detects the lane with the
sensor at the front windshield and warns
you when your vehicle leaves the lane.
5
66
Driving your vehicle
• When the sensor detects the lane line
OJD045180L
• When the sensor doesn’t detect the lane line
OJD045181L/OJD045182L
OJD055057L
1. Visual warning
If you change the display mode of trip
If you leave the lane, the lane you leave
computer while the LDWS is ON, the
on the LCD display blinks yellow with 0.8
symbol of the LDWS will display like a
second of interval.
picture.
The color of symbol will change depend
on the condition of LDWS system.
2. Auditory warning
- White color : It means the sensor does
If you leave the lane, the warning sound
not detect the lane line.
operates with 0.8 second of interval.
- Green color : It means the sensor detects
OJD045179L
the lane line.
If your vehicle leaves the lane when the
LDWS is operating and vehicle speed
exceeds 60km/h, the warning operates
as follows:
5 67
Driving your vehicle
The LDWS does not operate
•
Light reflects from the water on the
when:
road.
•
The lens or windshield is stained with
• The driver turns on the turn signal or
the hazard warning flasher to change
foreign matter.
lane.
•
The sensor can not detect the lane
• Driving on the lane line.
because of fog, heavy rain or heavy
snow.
•
The surrounding temperature of the
✽ NOTICE
inside rear view mirror is high due to a
To change lane, operate the turn signal
direct ray of light.
switch, then change the lane.
OUM054158L
•
The lane is very wide or narrow.
•
The lane line is damaged or indistinct.
The LDWS may not warn you even
•
The shadow is on the lane line by a
if the vehicle leaves the lane, or
median strip.
may warn you even if the vehicle
•
There is a mark similar to a lane line.
does not leave the lane when:
•
There is a boundary structure.
• The lane is not visible due to snow, rain,
•
The distance from vehicle ahead is
stain, a puddle or many other things.
very short or the vehicle ahead hides
• The brightness of the outside changes
the lane line.
suddenly.
•
The vehicle shakes heavily.
• Not turning on the headlight even at
•
The lane number increases or decreas-
OJD055174L
night or in the tunnel.
es or the lane lines are crossing com-
Warning indicator
• Difficult to distinguish the color of the
plicatedly.
lane from the road.
•
Putting something on the dashboard.
When the LDWS is not working properly,
the warning light will illuminate and the
• Driving on a steep grade or a curve.
•
Driving with the sun in front of you.
warning message will come on for a few
•
Driving in areas under construction.
second. After the message disappears,
•
The lane line is more than two in either
the master warning light will illuminate.
side (Left/Right).
We recommend that the system be
checked by an authorized Kia dealer.
5 68
Driving your vehicle
SPEED LIMIT INFORMATION FUNCTION (SLIF) (IF EQUIPPED)
WARNING
•
Speed Limit Information Function
is only an aid and is not always able
to correctly display speed limits
and overtaking restrictions.
•
The driver always keeps the
responsibility to not exceed the
maximum allowed speed
•
Do not place any accessories,
stickers or tint the windshield near
the rearview mirror.
OJD052029
OJD055153L
•
The system detects traffic signs
The system displays the information of
and displays speed limit informa-
SLIF activation / deactivation
speed limit and no passing restriction to
tion by a camera therefore, if traffic
• SLIF Setting method :
the driver in both the instrument cluster
signs are hard to detect, the system
Cluster User Settings Driving Assist
and navigation screen. SLIF detects traf-
may not work properly.
SLIF (Speed Limit Information
fic signs with camera system attached
Please refer to "Driver's Attention".
Function)
behind the top of the windscreen.
•
Do not remove any LDWS parts or
• The information of speed limit and no
The SLIF also utilizes the navigation
apply impact.
passing restriction will appear on the
information to display the speed limit
•
Do not place objects on the dash-
cluster using a symbol if you have acti-
information.
board that reflects light such as
vated SLIF in User Settings of cluster.
mirrors, white paper, etc. The sys-
• If SLIF is activated in navigation set-
tem may malfunction if the sunlight
ting, the information also displayed in
is reflected.
navigation screen.
•
The system is not available in all
countries.
5 69
Driving your vehicle
•
When the driver turn on the ignition,
■ No reliable speed limit information
the system displays stored information
of the speed limit before turn off the
ignition.
•
Sometimes different speed limits are
displayed for the same road. The infor-
mation displayed depending on the sit-
uation. Because, traffic signs with addi-
tional sign (e.g rainy, arrow...) are also
detected and compared with vehicle
WUM-203
interior data(e.g wiper operation, turn
Display
signal...).
OJD055173L
•
The system can update the speed limit
• If the system doesn’t have a reliable
speed limit information, the following
information without visible speed limit
Operation
symbol is displayed in both the instru-
signs in the following situations.
• If a traffic sign that is relevant to your
ment cluster and navigation screen.
- When you change your driving direc-
vehicle is passed, the system displays
tion with right or left or U turning.
the information of the speed limits and
- When vehicle changes roads. (e.g.
no passing restrictions to the driver.
from highway to country road…)
- When you enter or exit into town or
village.
✽ NOTICE
If speed limit value has the difference
between cluster and navigation, check
the speed unit setting in navigation.
5 70
Driving your vehicle
■ No passing information
■ End of a speed limit
■ Unlimited speed (only in Germany)
WUM-206/WUM-204
WUM-207/WUM-208
WUM-205
• If the system detect no passing sign,
• After passing "end of speed limitation“
• For some areas on highways in ger-
no passing is displayed in both the
sign SLIF provides information from
many there's no speed limit applicable.
instrument cluster and navigation
navigation to inform driver of perhaps
In that case SLIF shows "end of limita-
screen.
afterwards applicable speed limit.
tion" traffic sign as long as you don't
pass another speed limit sign.
5 71
Driving your vehicle
The system may not fully operate and
provide correct information in the follow-
ing situations.
•
Traffic signs are positioned on sharp
curve.
•
Poorly positioned traffic sign.
(eg.
Rotated, shaded by any object, dam-
aged…)
•
Concealed traffic signs by other vehicle.
•
Broken LED traffic signs.
OUM054154L
•
Poor weather like snow, rain, fog
•
There is glare around traffic signs by
OJD055155L
low sun in the sky.
Warning message
•
There is insufficient illumination of the
The message will appear when camera’s
traffic signs in the night.
field of view is covered by some objects.
•
There is bright lights around traffic signs.
The system stops until the field of view is
•
There is dirt, ice or frost on the wind-
normal.
shield in the area of the camera.
Check the windshield around the camera
•
When camera field of view is covered by
view area.
objects such as a sticker, paper, leaf fall.
If the system does not work normally
•
When driving very close to the vehicle
even though camera’s field of view is
OJD055174L
in front of you.
cleared, we recommend that the system
When SLIF is not working properly, the
•
When navigation system has malfunc-
be checked by an authorized Kia dealer.
warning message will come on for a few
tion.
second. After the message disappears,
•
When bus or trucks attached with a
the master warning light will illuminate.
speed sticker are passing you.
We recommend that the system be
•
When you are in area or countries
checked by an authorized Kia dealer.
where navigation system is not covered.
•
When a navigation system not updated
latest map version.
5 72
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст