Kia Stonic (2018 year). Manual — part 28
Symbol
Relay Name
Type
A/C Blower Relay
MICRO
Engine room compartment fuse panel
(U-II 1.4L/1.6L Engine (Diesel))
Symbol
Fuse rating
Circuit Protected
80A
MDPS Unit
ALT
150A
Fuse - RR DEFOG, ABS1, ABS2, BLOWER
40A
Rear Defogger Relay
1
40A
ABS/ESC (Electronic Stability Control) Control
40A
ABS/ESC (Electronic Stability Control) Control, Multipurpose Check Connector
40A
Air Conditioner Blower Relay
10A
Wiper Motor, Multifunction Switch, Wiper LO Relay
10A
PM Sensor, Electronic VGT Actuator, WGT Vacuum Modulator
10A
Lambda Sensor #1, #2, Rail Pressure Regulating Valve, Cooling Fan1 Relay, Cooling Fan2 Relay
15A
Camshaft Position Sensor, Air Flow Sensor, Oil Control Valve, PTC1 Heater Relay
10A
Head Lamp RH
10A
Head Lamp LH
Maintenance
8-100
Symbol
Fuse rating
Circuit Protected
E4
20A
ECM
S3
15A
EGR Cooling Bypass Solenoid, Fuel Pressure Regulating Valve, Stop Lamp Switch, Fuel Pump
Relay, A/C Blower Relay, Fuel Heat Relay
10A
Back-Up Lamp Switch
40A
Instrument Panel Junction Block
50A
Instrument Panel Junction Block (Power Window Relay)
40A
Ignition Switch, PDM Relay Box (IG2 Relay)
50A
Cooling Fan1 Relay, Cooling Fan2 Relay
40A
Fuel Heat Relay
30A
Main Relay
10A
Air Conditioner Clutch Type ECV Relay
20A
Not Used
20A
Head Lamp Relay
20A
Head Lamp High Relay
FUEL
PUMP
20A
Fuel Pump Relay
15A
Horn Relay, Burglar Alarm Horn Relay
E3
15A
ECM/PCM
8-101
8
Maintenance
Symbol
Fuse rating
Circuit Protected
AMS
10A
Battery Sensor
40A
Instrument Panel Junction Block (Tail Lamp Relay)
40A
Ignition Switch, PDM Relay Box (IG1 Relay, ACC Relay)
POWER
OUTLET
40A
Instrument Panel Junction Block (Power Outlet Relay)
Relay(U-II 1.4L/1.6L Engine (Diesel))
Symbol
Relay Name
Type
Start Relay
MICRO
A/C Blower Relay
MICRO
FUEL
PUMP
Fuel Pump Relay
MICRO
Cooling Fan1 Relay
MICRO
Wiper HI Relay
MICRO
LO
Wiper LO Relay
MICRO
Head Lamp High Relay
MICRO
Head Lamp Relay
MICRO
2
Cooling Fan2 Relay
MICRO
Horn Relay
MICRO
Maintenance
8-102
Symbol
Relay Name
Type
Burglar Alarm Horn Relay
MICRO
MAIN
Main Relay
MINI
A/C Blower Relay
MICRO
Fuel Heat Relay
MICRO
Diesel fuse box (U-II 1.4L/1.6L Engine
(Diesel))
Symbol
Relay Name
Type
PTC3 Heater Relay
MICRO
PTC2 Heater Relay
MICRO
PTC1 Heater Relay
MICRO
Symbol
Fuse rating
Circuit Protected
50A
PTC3 Heater Relay (RLY.3)
50A
PTC2 Heater Relay (RLY.2)
50A
PTC1 Heater Relay (RLY.1)
80A
Glow Relay Unit
8-103
8
Maintenance
LIGHT BULBS
Bulb replacement precaution
Please prepare bulbs with appropriate
standards in case of emergencies. Re‐
fer to Bulb wattage on page 9-04
for further information).
When changing bulbs and sorts, first
turn off the engine at a safe place,
firmly apply the side brake and take
out the battery's negative (-) terminal.
WARNING
n Working on the lights
Prior to working on the light, firmly
apply the parking brake, ensure that
the ignition switch is turned to the
LOCK position and turn off the lights
to avoid sudden movement of the
vehicle and burning your fingers or
receiving an electric shock.
Use only the bulbs of the specified wat‐
tage.
WARNING
Be sure to replace the burned-out
bulb with one of the same wattage
rating. Otherwise, it may cause ex‐
tensive wiring damage and possible
fire.
CAUTION
If you don't have necessary tools,
the correct bulbs and the expertise,
consult a professional workshop. Kia
recommends to consult an author‐
ized Kia dealer/ service partner.
In many cases, it is difficult to re‐
place vehicle light bulbs because oth‐
er parts of the vehicle must be re‐
moved before you can get to the
bulb. This is especially true if you
have to remove the headlight as‐
sembly to get to the bulb(s). Remov‐
ing/ installing the headlight assem‐
bly can result in damage to the vehi‐
cle.
CAUTION
• If unauthentic parts or substan‐
dard lights are used when chang‐
ing lights, it may lead to fuse dis‐
connection and malfunction, and
other wiring damages.
• Do not install extra lamps or LED
to the vehicle. If supplementary
lights are installed, it may lead to
lamp malfunction and flickering of
the lights. In addition, the fuse box
and other writing may be dam‐
aged.
• Lamp part malfunction due to net-
work failure
The headlamp, taillight, and fog light
may lit up when the head lamp
switch is turned ON, and not light up
when the taillight or for light switch
is turned ON. This may be cause by
network failure or vehicle electrical
control system malfunction. If there
is a problem, have the system serv‐
iced by a professional workshop. Kia
recommends to visit an authorized
Kia dealer/ service partner.
Maintenance
8-104
• Lamp part malfunction due to electri‐
cal control system stabilization
A normally functioning lamp may
flicker momentarily. This momentary
occurrence is due to stabilization unc‐
tion of the vehicle's electrical on con‐
trol system. If the lamp soon returns
to normal, the vehicle does not re‐
quire service.
However, if the lamp goes out after
he momentary flickering, or the flick‐
ering continues, have the system
serviced by a professional workshop.
Kia recommends to visit an author‐
ized Kia dealer/service partner.
NOTICE
• If the light bulb or lamp connector
is removed from an operating
lamp activated by electricity, the
fuse box’s electronic device may
scan it as a malfunction. There‐
fore, a lamp malfunction history
may be recorded in Diagnostic
Trouble Code (DTC) in the fuse
box.
(Continued)
(Continued)
• It is normal for an operating lamp
may blink temporarily. Since this
occurrence is due stabilization
function of the vehicle’s electronic
control device, if the lamp lights up
normally after temporary blinking,
there is no problem in the vehicle.
However, if the lamp continues to
blink several times or turn off
completely, there may be an error
in the vehicle’s electronic control
device. In this case, have the vehi‐
cle checked by a professional
workshop immediately. Kia recom‐
mends to visit an authorized Kia
dealer/service partner.
NOTICE
After an accident or after the head‐
light assembly is reinstalled, have
the headlight aiming adjusted by a
professional workshop. Kia recom‐
mends to visit an authorized Kia
dealer/service partner.
NOTICE
After driving in heavy rain or wash‐
ing, headlamp and taillamp lenses
could appear frosty. This condition is
caused by the temperature differ‐
ence between the lamp inside and
outside. This is similar to the con‐
densation on your windows inside
your vehicle during the rain and
doesn’t indicate a problem with your
vehicle. If the water leaks into the
lamp bulb circuitry, have the vehicle
checked by a professional workshop.
Kia recommends to visit an author‐
ized Kia dealer/service partner.
NOTICE
n Traffic Change (For Europe)
The low beam light distribution is
asymmetric. If you go abroad to a
country with opposite traffic direc‐
tion, this asymmetric part will dazzle
oncoming car driver. To prevent daz‐
(Continued)
8-105
8
Maintenance
(Continued)
zle, ECE regulation demand several
technical solutions (ex. automatic
change system, adhesive sheet,
down aiming). This headlamps are
designed not to dazzle opposite driv‐
ers. So, you need not change your
headlamps in a country with oppo‐
site traffic direction.
Light bulb position (Front)
OYB077038B
Head lamp - Type A
OYB077090B
Head lamp - Type B
OYB077040B
Fog lamp
1. Headlamp (Low/High)
2. Front turn signal lamp
3. Position lamp / Day time running
lamp (Bulb type)
4. Position lamp / Day time running
lamp (LED type)
5. Static bending light
6. Fog lamp
Maintenance
8-106
Light bulb position (Rear)
OYB077043B
Rear combination lamp - Type A
OYB077091B
Rear combination lamp - Type B
OYB077092B
Back up lamp
OYB077093B
Rear fog lamp
OYB077045B
License plate lamp
OYB077046B
High mounted stop lamp
1. Tail lamp (Bulb type)
2. Stop and tail lamp (Bulb type)
3. Rear turn signal lamp (Bulb type)
4. Tail lamp (LED type)
5. Tail lamp (LED type)
6. Stop and tail lamp (LED type)
8-107
8
Maintenance
7. Stop and tail lamp (LED type)
8. Back up lamp
9. Rear fog lamp
10. License plate lamp
11. High mounted stop lamp
Light bulb position (Side)
■ Type A
■ Type B
1. Side repeater lamp (LED type)
2. Side repeater lamp (bulb type)
Side repeater lamp (LED type)
bulb Replacement
If the side repeater lamp (LED) (1) does
not operate, have your vehicle checked
by a professional workshop.
Kia recommends to visit an authorized
Kia dealer/service partner.
The LED lamps cannot be replaced as a
single unit because it is an integrated
unit. The LED lamps has to be replaced
with the unit.
A skilled technician should check or re‐
pair side repeater lamp (LED), for it
may damage related parts of the vehi‐
cle.
Maintenance
8-108
Side repeater lamp (bulb type)
bulb Replacement
1. Remove the lamp assembly from
the vehicle by prying the lens and
pulling the assembly out.
2. Disconnect the bulb electrical con‐
nector.
3. Separate the socket and the lens
parts by turning the socket coun‐
terclockwise until the tabs on the
socket align with the slots on the
lens part.
4. Remove the bulb by pulling it
straight out.
5. Insert a new bulb in the socket.
6. Reassemble the socket and the
lens part.
7. Connect the bulb electrical connec‐
tor.
8. Reinstall the lamp assembly to the
body of the vehicle.
Headlamp (Low/High beam) bulb
replacement (Headlamp Type A)
OYB077052B
1. Open the hood.
2. Remove the headlamp bulb cover
by turning it counterclockwise.
3. Disconnect the headlamp bulb
socket-connector.
4. Remove the bulb-socket from the
headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
5. Install a new bulb-socket assembly
in the headlamp assembly by align‐
ing the tabs on the bulb-socket
with the slots in the headlamp as‐
sembly. Push the bulb-socket into
the headlamp assembly and turn
the bulb-socket clockwise.
6. Install the headlamp bulb cover by
turning it clockwise.
Headlamp bulb
8-109
8
Maintenance
WARNING
n Halogen bulbs
• Halogen bulbs contain pressurized
gas that will produce flying pieces
of glass if broken.
• Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact
with liquids. Never touch the glass
with bare hands. Residual oil may
cause the bulb to overheat and
burst when lit.
A bulb should be operated only
when installed in a headlight.
• If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
• Wear eye protection when chang‐
ing a bulb. Allow the bulb to cool
down before handling it.
Front turn signal lamp bulb
replacement (Headlamp Type A)
OYB077051B
1. Open the hood.
2. Remove the bulb-socket from the
headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb-
socket by pressing it in and rotat‐
ing it counterclockwise until the
tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket.
4. Insert a new bulb by inserting it in‐
to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp
assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.
Position lamp / Day time
running lamp bulb replacement
(Headlamp Type A)
OYB077094B
1. Open the hood.
Maintenance
8-110
2. Remove the bulb-socket from the
headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb-
socket by pressing it in and rotat‐
ing it counterclockwise until the
tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket.
4. Insert a new bulb by inserting it in‐
to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp
assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.
Headlamp (Low/High beam) bulb
replacement (Headlamp Type B)
OYB077095B
1. Open the hood.
2. Remove the headlamp bulb cover
by turning it counterclockwise.
3. Disconnect the headlamp bulb
socket-connector.
4. Remove the bulb-socket from the
headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
5. Install a new bulb-socket assembly
in the headlamp assembly by align‐
ing the tabs on the bulb-socket
with the slots in the headlamp as‐
sembly. Push the bulb-socket into
the headlamp assembly and turn
the bulb-socket clockwise.
6. Install the headlamp bulb cover by
turning it clockwise.
Headlamp bulb
8-111
8
Maintenance
WARNING
n Halogen bulbs
• Halogen bulbs contain pressurized
gas that will produce flying pieces
of glass if broken.
• Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact
with liquids. Never touch the glass
with bare hands. Residual oil may
cause the bulb to overheat and
burst when lit.
A bulb should be operated only
when installed in a headlight.
• If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
• Wear eye protection when chang‐
ing a bulb. Allow the bulb to cool
down before handling it.
Front turn signal lamp bulb
replacement (Headlamp Type B)
OYB077096B
1. Open the hood.
2. Remove the bulb-socket from the
headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb-
socket by pressing it in and rotat‐
ing it counterclockwise until the
tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket.
4. Insert a new bulb by inserting it in‐
to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp
assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.
Static bending light replacement
(Headlamp Type B)
OYB077097B
1. Open the hood.
2. Remove the headlamp bulb cover
by turning it counterclockwise.
Maintenance
8-112
3. Remove the bulb-socket from the
headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
4. Remove the bulb from bulb-socket
by pulling it out.
5. Insert a new bulb by inserting it in‐
to the bulb-socket.
6. Install the bulb-socket in the head‐
lamp assembly by aligning the tabs
on the bulb-socket with the slots in
the headlamp assembly. Push the
bulb-socket into the headlamp as‐
sembly and turn the bulb-socket
clockwise.
7. Install the headlamp bulb cover by
turning it clockwise.
Position lamp / Day time
running lamp (LED type)
replacement (Headlamp Type B)
OYB077098B
If the position lamp + DRL (LED) (1)
does not operate, have your vehicle
checked by a professional workshop.
Kia recommends to visit an authorized
Kia dealer/service partner.
The LED lamps cannot be replaced as a
single unit because it is an integrated
unit. The LED lamps has to be replaced
with the unit.
A skilled technician should check or re‐
pair the position lamp + DRL (LED), for
it may damage related parts of the ve‐
hicle.
Front fog lamp bulb
replacement
OYB077057B
If the front fog lamp (1) does not oper‐
ate, have your vehicle checked by a
professional workshop. Kia recom‐
mends to visit an authorized Kia dealer/
service partner.
8-113
8
Maintenance
Rear turn signal lamp bulb
replacement
OYB077060B
1. Open the tail gate.
2. Loosen the light assembly retaining
screws with a cross-tip screwdriv‐
er.
OYB077061B
3. Remove the rear combination lamp
assembly from the body of the ve‐
hicle.
4. Disconnect the rear combination
lamp connector.
OYB077099B
5. Remove the socket from the as‐
sembly by turning the socket coun‐
terclockwise until the tabs on the
socket align with the slots on the
assembly.
6. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
7. Insert a new bulb by inserting it in‐
to the socket and rotating it until it
locks into place.
8. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
9. Install the rear combination lamp
assembly to the body of the vehi‐
cle.
Maintenance
8-114
Stop and tail lamp bulb
replacement
OYB077060B
1. Open the tail gate.
2. Loosen the light assembly retaining
screws with a cross-tip screwdriv‐
er.
OYB077061B
3. Remove the rear combination lamp
assembly from the body of the ve‐
hicle.
4. Disconnect the rear combination
lamp connector.
OYB077100B
5. Remove the socket from the as‐
sembly by turning the socket coun‐
terclockwise until the tabs on the
socket align with the slots on the
assembly.
6. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
7. Insert a new bulb by inserting it in‐
to the socket and rotating it until it
locks into place.
8. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
9. Install the rear combination lamp
assembly to the body of the vehi‐
cle.
8-115
8
Maintenance
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст