KIA Stinger (2018 year). Manual — part 32

7 81

Maintenance

Headlamp (Low/High beam)
bulb replacement (Headlamp
Type A)

1. Remove the service cover clip on

the wheel housing.

2. Remove the headlamp bulb cover

by turning it counterclockwise.

3. Disconnect the headlamp bulb

socket-connector.

4. Remove the bulb-socket from the

headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp
assembly.

5. Install a new bulb-socket assem-

bly in the headlamp assembly by
aligning the tabs on the bulb-sock-
et with the slots in the headlamp
assembly. Push the bulb-socket
into the headlamp assembly and
turn the bulb-socket clockwise.

6. Connect the headlamp bulb sock-

et-connector.

7. Install the headlamp bulb cover by

turning it clockwise.

8. Install the clip on the service

cover.

❈ If it is difficult to replace light bulbs,

have the vehicle checked by an
authorized Kia dealer.

OCK077074

■ Head lamp - Type A

OCK077075

OCK077076

Maintenance

82

7

Headlamp bulb

• Never touch the glass with bare

hands. Residual oil may cause the
bulb to overheat and burst when lit.
A bulb should be operated only
when installed in a headlight.

• If a bulb becomes damaged or

cracked, replace it immediately
and carefully dispose of it.

• Wear eye protection when chang-

ing a bulb. Allow the bulb to cool
down before handling it.

Front turn signal lamp bulb
replacement (Headlamp Type A)

1. Open the hood.
2. Remove the strut bar and the air

cleaner assembly.

OQL075058

WARNING

- Halogen

bulbs

• Halogen bulbs contain pres-

surized gas that will produce
flying pieces of glass if broken.

• Always handle them carefully,

and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact with liquids.

OCK077077

OCK077078

7 83

Maintenance

3. Remove the bulb-socket from the

headlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp
assembly.

4. Remove the bulb from the bulb-

socket by pressing it in and rotat-
ing it counterclockwise until the
tabs on the bulb align with the
slots in the bulb-socket. Pull the
bulb out of the bulb-socket.

5. Insert a new bulb by inserting it

into the bulb-socket and rotating it
until it locks into place.

6. Install the socket in the headlamp

assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock-
et into the headlamp assembly
and turn the socket clockwise.

7. Install the strut bar and the air

cleaner assembly.

❈ If it is difficult to replace light bulbs,

have the vehicle checked by an
authorized Kia dealer.

Stop and tail lamp (LED type)
bulb replacement

If the stop and tail lamp (LED) (1,2),
does not operate, have the vehicle
checked by an authorized Kia dealer.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the stop and tail lamp (LED),
for it may damage related parts of
the vehicle.

OCK077053

OCK077079

Maintenance

84

7

Rear side marker (LED type)
bulb replacement

If the rear side marker (LED) (1),
does not operate, have the vehicle
checked by an authorized Kia dealer.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the rear side marker (LED), for
it may damage related parts of the
vehicle.

Rear turn signal lamp (LED
type) bulb replacement

If the rear turn signal lamp (LED) (1),
does not operate, have the vehicle
checked by an authorized Kia dealer.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the rear turn signal lamp
(LED), for it may damage related
parts of the vehicle.

Rear turn signal lamp (bulb
type) bulb replacement

1. Open the liftgate.
2. Open the service cover.

OCK077102L

OCK077087L

OCK077080

7 85

Maintenance

3. Loosen the light assembly retain-

ing screws with a cross-tip screw-
driver or spanner.

4. Remove the rear combination

lamp assembly from the body of
the vehicle.

5. Disconnect the rear combination

lamp connector.

6. Remove the socket from the

assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.

7. Remove the bulb from the socket

by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.

8. Insert a new bulb by inserting it

into the socket and rotating it until
it locks into place.

OCK077056

OCK077081

OCK077082

OCK077055

Maintenance

86

7

9. Install the socket in the assembly

by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.

10. Install the rear combination lamp

assembly to the body of the vehi-
cle.

11. Install the service cover.

Back-up lamp bulb replace-
ment

1. Open the liftgate.
2. Remove the service cover of both

side (drive side and passenger
side).

3. Remove the nuts from rear combi-

nation lamp of both side (drive
side and passenger side).

4. Disconnect the connector from

rear combination lamp of both side
(drive side and passenger side).

OCK077057

OCK077058

OCK077059

7 87

Maintenance

5. Remove the rear combination

lamp assembly from the body of
the vehicle.

6. Remove the socket from the

assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.

7. Remove the bulb from the socket by

pressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket.
Pull the bulb out of the socket.

8. Insert a new bulb by inserting it

into the socket and rotating it until
it locks into place.

9. Install the socket in the assembly

by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.

10. Install the rear combination lamp

assembly to the body of the vehi-
cle.

11. Install the service cover by put-

ting it into the service hole.

OCK077060

Maintenance

88

7

High mounted stop lamp (LED
type) bulb replacement

If the high mounted stop lamp (LED)
(1), does not operate, have the vehi-
cle checked by an authorized Kia
dealer.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the high mounted stop lamp
(LED), for it may damage related
parts of the vehicle.

License plate lamp (LED type)
bulb replacement

If the license plate lamp (LED) (1),
does not operate, have the vehicle
checked by an authorized Kia dealer.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the license plate lamp (LED),
for it may damage related parts of
the vehicle.

Side repeater lamp (LED type)
bulb replacement

If the side repeater lamp (LED) (1),
does not operate, have the vehicle
checked by an authorized Kia dealer.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the side repeater lamp (LED),
for it may damage related parts of
the vehicle.

OCK077061

OCK077062

OCK077052

7 89

Maintenance

Map lamp (LED type) bulb
replacement

If the map lamp (LED) (1), does not
operate, have the vehicle checked by
an authorized Kia dealer.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the map lamp (LED), for it may
damage related parts of the vehicle.

Vanity mirror lamp (LED type)
bulb replacement

If the vanity mirror lamp (LED) (1),
does not operate, have the vehicle
checked by an authorized Kia dealer.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the vanity mirror lamp (LED),
for it may damage related parts of
the vehicle.

Room lamp (LED type) bulb
replacement

If the room lamp (LED) (1), does not
operate, have the vehicle checked by
an authorized Kia dealer.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the room lamp (LED), for it
may damage related parts of the
vehicle.

OCK077065

OCK077063

OCK077064

Maintenance

90

7

Glove box lamp (LED type)
bulb replacement

If the glove box lamp (LED) (1), does
not operate, have the vehicle
checked by an authorized Kia dealer.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the glove box lamp (LED), for
it may damage related parts of the
vehicle.

Luggage room lamp (LED
type) bulb replacement

If the luggage room lamp (LED) (1),
does not operate, have the vehicle
checked by an authorized Kia dealer.
The LED lamps cannot be replaced
as a single unit because it is an inte-
grated unit. The LED lamps has to be
replaced with the unit.
A skilled technician should check or
repair the luggage room lamp (LED),
for it may damage related parts of
the vehicle.

OCK077066

OCK077067

7 91

Maintenance

APPEARANCE CARE

Exterior care

Exterior general caution

It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning
and caution statements that appear
on the label.

Finish maintenance

Washing
To help protect your vehicle’s finish
from rust and deterioration, wash it
thoroughly and frequently at least
once a month with lukewarm or cold
water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to
the removal of any accumulation of
salt, dirt, mud, and other foreign mate-
rials. Make sure the drain holes in the
lower edges of the doors and rocker
panels are kept clear and clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar
deposits can damage your vehicle’s
finish if not removed immediately.
Even prompt washing with plain water
may not completely remove all these
deposits. A mild soap, safe for use on
painted surfaces, may be used.
After washing, rinse the vehicle thor-
oughly with lukewarm or cold water.
Do not allow soap to dry on the finish.

After washing the vehicle, test the
brakes while driving slowly to see if
they have been affected by water. If
braking performance is impaired, dry
the brakes by applying them lightly
while maintaining a slow forward
speed.

Maintenance

92

7

High-pressure washing
• When using high-pressure wash-

ers, make sure to maintain suffi-
cient distance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.

• Do not spray the camera, sensors

or its surrounding area directly with
a high pressure washer. Shock
applied from high pressure water
may cause the device to not oper-
ate normally.

• Do not bring the nozzle tip close to

boots (rubber or plastic covers) or
connectors as they may be dam-
aged if they come into contact with
high pressure water.

Waxing
Wax the vehicle when water will no
longer bead on the paint.
Always wash and dry the vehicle
before waxing. Use a good quality
liquid or paste wax, and follow the
manufacturer’s instructions. Wax all
metal trim to protect it and to main-
tain its luster.
Removing oil, tar, and similar materi-
als with a spot remover will usually
strip the wax from the finish. Be sure
to re-wax these areas even if the rest
of the vehicle does not yet need wax-
ing.
Do not apply wax on embossed
unpainted unit, as it may tarnish the
unit.

CAUTION -

Wet engine

• Water washing in the engine

compartment including high
pressure water washing may
cause the failure of electrical
circuits located in the engine
compartment.

• Never allow water or other liq-

uids to come in contact with
electrical/electronic compo-
nents inside the vehicle as
this may damage them.

OCK077070

7 93

Maintenance

Finish damage repair

Deep scratches or stone chips in the
painted surface must be repaired
promptly. Exposed metal will quickly
rust and may develop into a major
repair expense.
If your vehicle is damaged and
requires any metal repair or replace-
ment, be sure the body shop applies
anti-corrosion materials to the parts
repaired or replaced.

Bright-metal maintenance

• To remove road tar and insects,

use a tar remover, not a scraper or
other sharp object.

• To protect the surfaces of bright-

metal parts from corrosion, apply a
coating of wax or chrome preser-
vative and rub to a high luster.

• During winter weather or in coastal

areas, cover the bright metal parts
with a heavier coating of wax or
preservative. If necessary, coat the
parts with non-corrosive petroleum
jelly or other protective compound.

Underbody maintenance

Road salt and other corrosive chemi-
cals are used in cold weather states to
melt snow and prevent ice accumula-
tion. If these chemicals are not regu-
larly removed, they will corrode the
vehicle underbody and over time dam-
age fuel lines, the fuel tank retention
system, the vehicle suspension, the
exhaust system, and even the body
frame. The National Highway Traffic
Safety Administration has warned all
vehicle owners of all brands of the
need to take the following steps:
• Wash the undercarriage of your

vehicle regularly during the winter
and whenever your vehicle has
been exposed to such salts or
chemicals.

CAUTION -

Drying vehicle

• Wiping dust or dirt off the

body with a dry cloth will
scratch the finish.

• Do not use steel wool, abra-

sive cleaners, acid detergents
or strong detergents contain-
ing high alkaline or caustic
agents on chrome-plated or
anodized aluminum parts.
This may result in damage to
the protective coating and
cause discoloration or paint
deterioration.

Maintenance

94

7

• Do a thorough washing of the

undercarriage at the end of the
winter.

• Use professional service techni-

cians or governmental inspection
stations to annually inspect for cor-
rosion.

• Immediately seek an inspection of

your vehicle if you become visually
aware of corrosion flaking or scal-
ing or if you become aware of a
change in vehicle performance,
such as soft or spongey brakes,
fluids leaking, impairment of direc-
tional control, suspension noises
or rattling metal straps.

Aluminum wheel maintenance

The aluminum wheels are coated
with a clear protective finish.
• Do not use any abrasive cleaner,

polishing compound, solvent, or
wire brushes on aluminum wheels.
They may scratch the finish.

• Clean the wheel when it has

cooled.

• Use only a mild soap or neutral

detergent, and rinse thoroughly
with water. Also, be sure to clean
the wheels after driving on salted
roads. This helps prevent corro-
sion.

• Avoid washing the wheels with

highspeed vehicle wash brushes.

• Do not use any alkaline or acid

detergents It may damage and cor-
rode the aluminum wheels coated
with a clear protective finish.

Corrosion protection

Protecting your vehicle from corrosion
By using the most advanced design
and construction practices to combat
corrosion, we produce vehicles of
the highest quality. However, this is
only part of the job. To achieve the
long-term corrosion resistance your
vehicle can deliver, the owner's
cooperation and assistance is also
required.

Common causes of corrosion
The most common causes of corro-
sion on your vehicle are:
• Road salt, dirt and moisture that is

allowed to accumulate underneath
the vehicle.

• Removal of paint or protective

coatings by stones, gravel, abra-
sion or minor scrapes and dents
which leave unprotected metal
exposed to corrosion.

7 95

Maintenance

High-corrosion areas
If you live in an area where your vehi-
cle is regularly exposed to corrosive
materials, corrosion protection is
particularly important. Some of the
common causes of accelerated cor-
rosion are road salts, dust control
chemicals, ocean air and industrial
pollution.

Moisture breeds corrosion
Moisture creates the conditions in
which corrosion is most likely to
occur. For example, corrosion is
accelerated by high humidity, partic-
ularly when temperatures are just
above freezing. In such conditions,
the corrosive material is kept in con-
tact with the vehicle’s surface by
moisture that evaporates slowly.
Mud is particularly corrosive
because it dries slowly and holds
moisture in contact with the vehicle.
Although the mud appears to be dry,
it can still retain the moisture and
promote corrosion.

High temperatures can also acceler-
ate corrosion of parts that are not
properly ventilated so the moisture
can be dispersed. For all these rea-
sons, it is particularly important to
keep your vehicle clean and free of
mud or accumulations of other mate-
rials. This applies not only to the vis-
ible surfaces but particularly to the
underside of the vehicle.

To help prevent corrosion
You can help prevent corrosion from
beginning by observing the following:

Keep your vehicle clean

The best way to prevent corrosion is
to keep your vehicle clean and free
of corrosive materials. Attention to
the underside of the vehicle is partic-
ularly important.

• If you live in a high-corrosion area

— where road salts are used, near
the ocean, areas with industrial
pollution, acid rain, etc.—, you
should take extra care to prevent
corrosion. In winter, hose off the
underside of your vehicle at least
once a month and be sure to clean
the underside thoroughly when
winter is over.

• When cleaning underneath the

vehicle, give particular attention to
the components under the fenders
and other areas that are hidden
from view. Do a thorough job; just
dampening the accumulated mud
rather than washing it away will
accelerate corrosion rather than
prevent it. Water under high pres-
sure and steam are particularly
effective in removing accumulated
mud and corrosive materials.

Maintenance

96

7

• When cleaning lower door panels,

rocker panels and frame members,
be sure that drain holes are kept
open so that moisture can escape
and not be trapped inside to accel-
erate corrosion.

Keep your garage dry

Don't park your vehicle in a damp,
poorly ventilated garage. This cre-
ates a favorable environment for cor-
rosion. This is particularly true if you
wash your vehicle in the garage or
drive it into the garage when it is still
wet or covered with snow, ice or
mud. Even a heated garage can con-
tribute to corrosion unless it is well
ventilated so moisture is dispersed.

Keep paint and trim in good con-
dition

Scratches or chips in the finish
should be covered with "touch-up"
paint as soon as possible to reduce
the possibility of corrosion. If bare
metal is showing through, the atten-
tion of a qualified body and paint
shop is recommended.

Bird droppings : Bird droppings are
highly corrosive and may damage
painted surfaces in just a few hours.
Always remove bird droppings as
soon as possible.

Don't neglect the interior

Moisture can collect under the floor
mats and carpeting and cause corro-
sion. Check under the mats periodi-
cally to be sure the carpeting is dry.
Use particular care if you carry fertil-
izers, cleaning materials or chemi-
cals in the vehicle.
These should be carried only in prop-
er containers and any spills or leaks
should be cleaned up, flushed with
clean water and thoroughly dried.

Interior care

Interior general precautions

Prevent chemicals such as perfume,
cosmetic oil, sun cream, hand clean-
er, and air freshener from contacting
the interior parts because they may
cause damage or discoloration. If
they do contact the interior parts,
wipe them off immediately. If neces-
sary, use a vinyl cleaner, see product
instructions for correct usage.