Chrysler 200 (2017 year). Instruction — part 31
Exterior Bulbs
Bulb Number
High Intensity Discharge Headlamp
HID Bulb – D3S HID Bulb
Bi-Halogen Headlamp
9005HL+
Daytime Running Lamp
HID HDLP– LED
Hal HDLP– Reduced Voltage LB 9005HL+
Front Turn Signal Lamp
PWY24W SV
Side Marker Lamp
W3W
Front Park Lamp
Hal HDLP – PWY24W SV (common with turn)
Base Hal HDLP – LED in light pipe
HID HDLP – LED in light guide (common with DRL)
Front Fog Lamp
H11
LED Front Fog Lamp
LED (Serviced at Authorized Dealer)
Center High Mounted Stop (CHMSL) Lamp
LED (Serviced at Authorized Dealer)
Stop/Turn Signal Lamp
W21W
Rear Tail/Side Marker Lamp
LED (Serviced at Authorized Dealer)
Backup Lamp
921
License Lamp
W5W
7
MAINTAINING YOUR VEHICLE
489
-------------------------------------------------------------------------------------------------------------------------------------------------------------
BULB REPLACEMENT
NOTE:
Lens fogging can occur under certain atmospheric
conditions. This will usually clear as atmospheric condi-
tions change to allow the condensation to change back into
a vapor. Turning the lamps on will usually accelerate the
clearing process.
Low Beam And High Beam Headlamps
Bi-Xenon High Intensity Discharge (HID)
Headlamps — If Equipped
The headlamps contain a type of high voltage discharge
light source. High voltage can remain in the circuit even
with the headlamp switch off. Because of this, you should
not attempt to service a HID headlamp light source your-
self. If an HID headlamp light source fails, take your
vehicle to an authorized dealer for service.
NOTE:
On vehicles equipped with HID headlamps, when
the headlamps are turned on, there is a blue hue to the
lights. This diminishes and becomes more white after
approximately 10 seconds, as the system charges.
WARNING!
A transient high voltage occurs at the bulb sockets of
HID headlamps when the headlamp switch is turned
ON. It may cause serious electrical shock or electrocu-
tion if not serviced properly. See your authorized
dealer for service.
Bi-Halogen Headlamps
1. Remove the top pushpin on the headlamp access door in
the wheel liner to access the headlamp assembly.
Access Door
490
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2. Reach behind the headlamp housing to access the
headlamp bulb cap.
3. Firmly grasp the headlamp bulb cap and rotate it
counterclockwise to unlock it.
4. Firmly grasp the headlamp bulb socket assembly and
rotate counterclockwise to remove from the housing.
Headlamp Bulb Cap
Headlamp Bulb Socket
7
MAINTAINING YOUR VEHICLE
491
-------------------------------------------------------------------------------------------------------------------------------------------------------------
5. Disconnect the bulb from the electrical connector and
then connect the replacement bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
6. Install the bulb and connector assembly into the head-
lamp housing and rotate clockwise to lock it in place.
7. Install the headlamp bulb cap in the headlamp housing
and rotate clockwise to lock it in place.
8. Lock headlamp access door in wheel liner.
Front Turn Signal Lamp
1. Open the hood.
NOTE:
Removal of the air cleaner filter housing may be
necessary prior to replacing bulbs in the lamp assembly on
the passenger side of the vehicle.
2. Remove the beauty cover, by removing all push pins
and lifting beauty cover.
Headlamp Bulb
Beauty Cover
492
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
3. Remove the brace by removing the four fasteners and
loosening the 5th inboard fastener.
4. Twist the front turn signal lamp socket assembly coun-
terclockwise, and then remove the front turn signal
lamp assembly from the lamp housing.
5. Pull the bulb out of the socket and insert the replace-
ment bulb.
6. Install the front turn signal lamp socket assembly into
the housing, and rotate the front turn signal lamp socket
clockwise to lock it in place.
7. Install air cleaner filter housing, if removed.
8. Install brace, brace bolts and tighten as shown.
9. Install beauty cover.
Front Turn Signal Lamp Socket
Brace Bolt Tightening Sequence
7
MAINTAINING YOUR VEHICLE
493
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Front Side Marker Lamps
1. Remove the three fasteners from the inner wheel liner
and carefully peel back liner for access.
2. Firmly grasp the front side marker lamp socket and
rotate 1/4 turn counterclockwise to remove it from the
lamp assembly.
3. Remove bulb from the front side marker lamp socket
and replace with a new bulb.
4. Install front side marker lamp socket in lamp assembly
and rotate 1/4 turn clockwise to lock into place.
5. Position the inner wheel liner in place and install the
three fasteners.
Inner Wheel Liner Fasteners
Front Side Marker Lamp Bulb Removal
494
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Front Fog Lamp
1. Remove the three fasteners from the lower closeout, and
peel down the lower closeout.
2. Reach behind the fog lamp housing to access the bulb.
3. Rotate the front fog lamp socket counterclockwise, and
remove the bulb and socket assembly from the front fog
lamp housing.
4. Pull the bulb out of the socket and insert the replace-
ment bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
5. Install the front fog lamp socket assembly into the into
the front fog lamp housing, and rotate the connector
clockwise to lock it in place.
Lower Closeout
Front Fog Lamp Socket
7
MAINTAINING YOUR VEHICLE
495
-------------------------------------------------------------------------------------------------------------------------------------------------------------
6. Position the lower closeout panel in place and secure
with the three fasteners.
Backup Lamps (Passenger Side)
1. Open trunk lid.
2. Remove the passenger side access cover.
3. Remove the inner trunk lid handle cover.
4. Remove the two screws and remove the inner trunk lid
handle.
NOTE:
If necessary remove any additional inner deck lid
trim push pins to gain access.
5. Gently pull back the inner deck panel behind the trunk
lid lamp housing to expose the backup lamp socket.
6. Rotate the backup lamp socket counter clockwise 1/4
turn to remove the backup lamp socket from the trunk
lid lamp housing.
Inner Deck Panel
496
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Backup Lamp Socket
7. Remove the bulb from the socket and install the replace-
ment bulb.
8. Install the backup lamp socket into the trunk lid lamp
housing.
9. Rotate backup lamp socket clockwise 1/4 turn to lock it
into place.
10. Reposition the inner deck panel and secure with a push
pin if removed.
11. Install access cover.
Backup Lamps (Driver Side)
1. Open trunk lid.
2. Remove the drivers side access cover.
3. Remove inner deck lid support push pin.
NOTE:
If necessary remove any additional inner deck lid
trim push pins to gain access.
4. Gently pull back the inner deck panel behind the trunk
lid lamp housing to expose the backup lamp socket.
NOTE:
Passenger side is shown. The driver’s side is
similar.
7
MAINTAINING YOUR VEHICLE
497
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Backup Lamp Socket
5. Rotate the backup lamp socket counter clockwise 1/4
turn to remove the backup lamp socket from the trunk
lid lamp housing.
6. Remove the bulb from the socket and install the replace-
ment bulb.
7. Install the backup lamp socket into the trunk lid lamp
housing.
8. Rotate backup lamp socket clockwise 1/4 turn to lock it
into place.
9. Reposition the inner deck panel and secure with a push
pin if removed.
10. Install the access cover.
Stop/Rear Turn Signal Lamp
1. Open the trunk lid.
2. Remove the tail lamp housing beauty cover by grasping
the top edge and pulling rearward to expose the tail
lamp housing bolts.
3. Remove the tail lamp housing bolts.
Tail Lamp Beauty Cover
498
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
4. Pull the tail lamp housing directly rearward to dislodge
the two out bored ball studs from the socket fasteners.
NOTE:
It may be necessary to use significant force to
remove the two out bored ball studs from the socket
fasteners to remove the tail lamp housing.
5. Rotate the stop/rear turn signal lamp socket 1/4 turn
counterclockwise and remove it from the tail lamp
housing.
6. Remove the bulb from the socket and install the replace-
ment bulb.
7. Install the bulb socket into the tail lamp housing and
rotate the bulb socket ¼ turn clockwise to lock it in
place.
8. Install the tail lamp housing.
9. Install the tail lamp housing beauty cover.
License Plate Lamp
1. Remove the screw of the license plate lamp assembly
and pull down on the license plate lamp assembly to
remove.
2. Remove the bulb from the socket and install the replace-
ment bulb.
3. Install the license plate lamp assembly.
Tail Lamp Bolts
7
MAINTAINING YOUR VEHICLE
499
-------------------------------------------------------------------------------------------------------------------------------------------------------------
FLUID CAPACITIES
U.S.
Metric
Fuel (Approximate)
2.4L and 3.6L Engines
15.8 Gallons
60 Liters
Engine Oil With Filter
2.4 Liter Engine (SAE 0W-20,
API Certified)
5.5 Quarts
5.2 Liters
3.6 Liter Engine (SAE 5W-20,
API Certified)
6 Quarts
5.6 Liters
Cooling System*
2.4 Liter Engine (MOPAR Antifreeze/
Engine Coolant 10 Year/
150,000 Mile Formula)
7.2 Quarts
6.8 Liters
3.6 Liter Engine (MOPAR Antifreeze/
Engine Coolant 10 Year/
150,000 Mile Formula)
8.7 Quarts
8.2 Liters
* Includes heater and coolant reservoir filled to MAX level.
500
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
FLUIDS, LUBRICANTS, AND GENUINE PARTS
Engine
Component
Fluid, Lubricant, or Genuine Part
Engine Coolant
We recommend you use MOPAR Antifreeze/Coolant
10 Year/150,000 Mile Formula OAT (Organic Additive
Technology) or equivalent meeting the requirements of
FCA Material Standard MS.90032.
Engine Oil – 2.4L Engine
We recommend you use SAE 0W-20 API Certified Engine
Oil, meeting the requirements of FCA Material Standard
MS-6395 such as MOPAR, Pennzoil, and Shell Helix. Refer
to your engine oil filler cap for correct SAE grade.
Engine Oil – 3.6L Engine
We recommend you use API Certified SAE 5W-20 Engine
Oil, meeting the requirements of FCA Material Standard
MS-6395 such as MOPAR, Pennzoil, and Shell Helix. Refer
to your engine oil filler cap for correct SAE grade.
Engine Oil Filter
We recommend you use a MOPAR Engine Oil Filter.
Spark Plugs
We recommend you use MOPAR Spark Plugs.
Fuel Selection – 2.4L Engine
87 Octane, 0-15% Ethanol.
Fuel Selection – 2.4L Flex Fuel (E85) Engine – If Equipped
87 Octane, Up To 85% Ethanol.
Fuel Selection – 3.6L Engine
87 Octane, 0-15% Ethanol.
Fuel Selection – 3.6L Flex Fuel (E85) Engine – If Equipped
87 Octane, Up To 85% Ethanol.
7
MAINTAINING YOUR VEHICLE
501
-------------------------------------------------------------------------------------------------------------------------------------------------------------
CAUTION!
• Mixing of engine coolant (antifreeze) other than speci-
fied Organic Additive Technology (OAT) engine cool-
ant (antifreeze), may result in engine damage and may
decrease corrosion protection. Organic Additive Tech-
nology (OAT) engine coolant is different and should
not be mixed with Hybrid Organic Additive Technol-
ogy (HOAT) engine coolant (antifreeze) or any “glob-
ally compatible” coolant (antifreeze). If a non-OAT
engine coolant (antifreeze) is introduced into the cool-
ing system in an emergency, the cooling system will
need to be drained, flushed, and refilled with fresh
(Continued)
CAUTION! (Continued)
OAT coolant (conforming to MS.90032), by an autho-
rized dealer as soon as possible.
• Do not use water alone or alcohol-based engine
coolant (antifreeze) products. Do not use additional
rust inhibitors or antirust products, as they may not
be compatible with the radiator engine coolant and
may plug the radiator.
• This vehicle has not been designed for use with
propylene glycol-based engine coolant (antifreeze).
Use of propylene glycol-based engine coolant (anti-
freeze) is not recommended.
502
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Chassis
Component
Fluid, Lubricant, or Genuine Part
Automatic Transmission
Use only MOPAR ZF 8&9 Speed ATF Automatic Transmis-
sion Fluid, or equivalent.
Failure to use the correct fluid may affect the function or
performance of your transmission.
Brake Master Cylinder
We recommend you use MOPAR DOT 3 Brake Fluid,
SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid
is not available, then DOT 4 is acceptable. Use only
recommended brake fluids.
7
MAINTAINING YOUR VEHICLE
503
-------------------------------------------------------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст