Nissan Pathfinder (2005 year). Instruction — part 408
AUTOMATIC DRIVE POSITIONER
SE-59
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
3.
CHECK HARNESS CONTINUITY 1
1.
Turn ignition OFF.
2.
Disconnect automatic drive positioner control unit and door mirror RH.
3.
Check continuity between automatic drive positioner control unit connector M34 terminals 33, 41 and door
mirror RH connector D107 terminals 4, 9.
4.
Check continuity between automatic drive positioner control unit
connector M34 terminals 33, 41 and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness.
4.
CHECK HARNESS CONTINUITY 2
1.
Disconnect automatic drive positioner control unit and door mirror RH.
2.
Check continuity between automatic drive positioner control unit connector M33 terminals 5, 21 and door
mirror RH connector D107 terminals 5, 10.
3.
Check continuity between automatic drive positioner control unit
connector M33 terminals 5, 21 and ground.
OK or NG
OK
>> Replace door mirror RH. Refer to
.
NG
>> Repair or replace harness.
33 - 4
: Continuity should exist.
41 - 9
: Continuity should exist.
33 - Ground
: Continuity should not exist.
41 - Ground
: Continuity should not exist.
LIIA1771E
5 - 10
: Continuity should exist.
21 - 5
: Continuity should exist.
5 - Ground
: Continuity should not exist.
21 - Ground
: Continuity should not exist.
LIIA1772E
SE-60
AUTOMATIC DRIVE POSITIONER
2005 Pathfinder
Sliding Switch Circuit Inspection
EIS0045T
1.
CHECK FUNCTION
With CONSULT-II
With “SLIDE SW-FR, SLIDE SW-RR” on the DATA MONITOR, oper-
ate the sliding switch to check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and ground.
OK or NG
OK
>> Sliding switch circuit is OK.
NG
>> GO TO 2.
2.
CHECK SLIDING SWITCH CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit connector and power seat switch LH connector.
2.
Check continuity between driver seat control unit connector P2
terminals 11, 26 and power seat switch LH connector P8 termi-
nals 1, 7.
3.
Check continuity between driver seat control unit connector P2
terminals 11, 26 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
Monitor item [OPER-
ATION or UNIT]
Contents
SLIDE SW–
FR
"ON/
OFF"
ON / OFF status judged from the sliding switch (FR) sig-
nal is displayed.
SLIDE SW–
RR
"ON/
OFF"
ON / OFF status judged from the sliding switch (RR) sig-
nal is displayed.
PIIA0313E
Connector
Terminal
Condition
Voltage (V)
(Approx.)
(+)
(–)
P2
11
Ground
Sliding switch ON
(BACKWARD oper-
ation)
0
Other than above
Battery voltage
26
Sliding switch ON
(FORWARD opera-
tion)
0
Other than above
Battery voltage
PIIA4577E
11 - 7
: Continuity should exist.
26 - 1
: Continuity should exist.
11 - Ground
: Continuity should not exist.
26 - Ground
: Continuity should not exist.
LIIA1125E
AUTOMATIC DRIVE POSITIONER
SE-61
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
3.
CHECK SLIDING SWITCH
Check continuity between power seat switch LH as follows.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace power seat switch LH.
Reclining Switch Inspection
EIS0045U
1.
CHECK FUNCTION
With CONSULT-II
With “RECLN SW-FR, RECLN SW-RR” on the DATA MONITOR,
operate the reclining switch to check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and
ground.
OK or NG
OK
>> Reclining switch circuit is OK.
NG
>> GO TO 2.
Connector
Terminal
Condition
Continuity
P8
7
3
Sliding switch ON (BACKWARD
operation)
Yes
Other than above
No
1
Sliding switch ON (FORWARD
operation)
Yes
Other than above
No
LIIA1126E
Monitor item [OPERA-
TION or UNIT]
Contents
RECLN SW
–FR
“ON/
OFF”
ON/OFF status judged from the reclining switch (FR)
signal is displayed.
RECLIN S
W–RR
“ON/
OFF”
ON/OFF status judged from the reclining switch (RR)
signal is displayed.
PIIA0313E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
P2
12
Ground
Reclining switch ON
(BACKWARD oper-
ation)
0
Other than above
Battery voltage
27
Reclining switch ON
(FORWARD opera-
tion)
0
Other than above
Battery voltage
PIIA4580E
SE-62
AUTOMATIC DRIVE POSITIONER
2005 Pathfinder
2.
CHECK RECLINING SWITCH CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit and power seat switch LH.
2.
Check continuity between driver seat control unit connector P2
terminals 12, 27 and power seat switch LH connector P8 termi-
nals 9, 10.
3.
Check continuity between driver seat control unit connector P2
terminals 12, 27 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
3.
RECLINING SWITCH INSPECTION
Check continuity between power seat switch LH as follows.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace power seat switch LH.
12 - 9
: Continuity should exist.
27 - 10
: Continuity should exist.
12 - Ground
: Continuity should not exist.
27 - Ground
: Continuity should not exist.
LIIA1127E
Connector
Terminal
Condition
Continuity
P8
9
3
Reclining switch ON (BACKWARD
operation)
Yes
Other than above
No
10
Reclining switch ON (FORWARD
operation)
Yes
Other than above
No
LIIA1128E
AUTOMATIC DRIVE POSITIONER
SE-63
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
Lifting Switch (Front) Circuit Inspection
EIS0045V
1.
CHECK FUNCTION
With CONSULT-II
With “LIFT FR SW-UP, LIFT FR SW-DN” on the DATA MONITOR,
operate the lifting switch (front) to check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and
ground.
OK or NG
OK
>> Lifting switch (front) circuit is OK.
NG
>> GO TO 2.
2.
CHECK LIFTING SWITCH (FRONT) CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit and power seat switch LH.
2.
Check continuity between driver seat control unit connector P2
terminals 13, 28 and power seat switch LH connector P2 termi-
nals 5, 6.
3.
Check continuity between driver seat control unit connector P2
terminals 13, 28 and ground
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
Monitor item [OPERA-
TION or UNIT]
Contents
LIFT FR SW–
DN
"ON/
OFF"
ON / OFF status judged from the FR lifter switch
(DOWN) signal is displayed.
LIFT RR SW–
UP
"ON/
OFF"
ON / OFF status judged from the RR lifter switch (UP)
signal is displayed.
PIIA0323E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
P2
13
Ground
Lifting switch (front) ON
(DOWN operation)
0
Other than above
Battery voltage
28
Lifting switch (front) ON
(UP operation)
0
Other than above
Battery voltage
PIIA4583E
13 - 5
: Continuity should exist.
28 - 6
: Continuity should exist.
13 - Ground
: Continuity should not exist.
28 - Ground
: Continuity should not exist.
LIIA1129E
SE-64
AUTOMATIC DRIVE POSITIONER
2005 Pathfinder
3.
CHECK LIFTING SWITCH (FRONT)
Check continuity between power seat switch LH as follows.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace power seat switch LH.
Lifting Switch (Rear) Circuit Inspection
EIS0045W
1.
CHECK FUNCTION
With CONSULT-II
With “LIFT RR SW-UP, LIFT RR SW-DN” on the DATA MONITOR,
operate the rear lifting switch to check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and
ground.
OK or NG
OK
>> Rear lifting switch circuit is OK.
NG
>> GO TO 2.
Connector
Terminals
Condition
Continuity
P8
5
3
Lifting switch (front) ON
(DOWN operation)
Yes
Other than above
No
6
Lifting switch (front) ON
(UP operation)
Yes
Other than above
No
LIIA1130E
Monitor item [OPERATION or
UNIT]
Contents
LIFT RR SW–UP
“ON/OFF”
Operation (ON)/open (OFF) status judged
from the RR lifter switch (UP) signal is dis-
played.
LIFT RR SW–DN
“ON/OFF”
Operation (ON)/open (OFF) status judged
from the RR lifter switch (DOWN) signal is
displayed.
PIIA0323E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
P2
14
Ground
Rear lifting switch ON
(DOWN operation)
0
Other than above
Battery voltage
29
Rear lifting switch ON
(UP operation)
0
Other than above
Battery voltage
PIIA4586E
AUTOMATIC DRIVE POSITIONER
SE-65
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
2.
CHECK LIFTING SWITCH (REAR) CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit and power seat switch LH.
2.
Check continuity between driver seat control unit connector P2
terminals 14, 29 and power seat switch connector P8 terminals
2, 8.
3.
Check continuity between driver seat control unit connector P2
terminals 14, 29 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
3.
CHECK LIFTING SWITCH (REAR)
Check continuity between power seat switch LH as follows.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace power seat switch LH.
Power Seat Switch Ground Inspection
EIS0045X
1.
CHECK POWER SEAT SWITCH GROUND CIRCUIT
Check continuity between power seat switch LH connector P8 termi-
nal 3 and ground.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Repair or replace harness.
14 - 8
: Continuity should exist.
29 - 2
: Continuity should exist.
14 - Ground
: Continuity should not exist.
29 - Ground
: Continuity should not exist.
LIIA1131E
Connector
Terminals
Condition
Continuity
P8
8
3
Lifting switch (rear) ON
(DOWN operation)
Yes
Other than above
No
2
Lifting switch (rear) ON
(UP operation)
Yes
Other than above
No
LIIA1132E
3 - Ground
: Continuity should exist.
LIIA1133E
SE-66
AUTOMATIC DRIVE POSITIONER
2005 Pathfinder
Pedal Adjusting Switch Circuit Inspection
EIS0045Y
1.
CHECK FUNCTION
With CONSULT-II
With “PEDAL SW-FR, PEDAL SW-RR” on the DATA MONITOR,
operate the pedal adjusting switch to check ON/OFF operation.
Without CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between driver seat control unit connector and
ground.
OK or NG
OK
>> Pedal adjusting switch circuit is OK.
NG
>> GO TO 2.
2.
CHECK PEDAL ADJUSTING SWITCH CIRCUIT HARNESS CONTINUITY
1.
Disconnect driver seat control unit and pedal adjusting switch.
2.
Check continuity between driver seat control unit connector P2
terminals 15, 30 and pedal adjusting switch connector M96 ter-
minals 2, 3.
3.
Check continuity between driver seat control unit connector P2
terminals 15, 30 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
Monitor item [OPERATION or
UNIT]
Contents
PEDAL SW–FR
“ON/OFF”
Operation (ON)/open (OFF) status
judged from the pedal adjusting switch
(FR) signal is displayed.
PEDAL SW–RR
“ON/OFF”
Operation (ON)/open (OFF) status
judged from the pedal adjusting switch
(RR) signal is displayed.
PIIA4590E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
P2
15
Ground
Pedal adjusting switch
ON (BACKWARD oper-
ation)
0
Other than above
Battery voltage
30
Pedal adjusting switch
ON (FORWARD opera-
tion)
0
Other than above
Battery voltage
PIIA4591E
15 - 2
: Continuity should exist.
30 - 3
: Continuity should exist.
15 - Ground
: Continuity should not exist.
30 - Ground
: Continuity should not exist.
LIIA0726E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст