Nissan Pathfinder (2005 year). Instruction — part 410
AUTOMATIC DRIVE POSITIONER
SE-75
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
3.
CHECK MIRROR SENSOR GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between automatic drive positioner control unit
connector M34 terminal 41 and ground.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace automatic drive positioner control unit.
A/T Device (Detent Switch) Circuit Inspection
EIS00465
1.
CHECK FUNCTION
With CONSULT-II
Check that when the A/T selector lever is in P position, “DETENT
SW” on the DATA MONITOR becomes OFF.
Without CONSULT-II
GO TO 2.
OK or NG
OK
>> A/T device (detent switch) circuit is OK.
NG
>> GO TO 2.
2.
CHECK A/T DEVICE (DETENT SWITCH) HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect A/T device and driver seat control unit.
3.
Check continuity between A/T device connector M156 terminal 4
and driver seat control unit connector P2 terminal 21.
4.
Check continuity between A/T device connector M156 terminal 4
and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
41 - Ground
: Continuity should exist.
LIIA1135E
Monitor item
[OPERATION or UNIT]
Contents
DETENT SW
“ON/
OFF”
The selector lever position “P position (OFF)/other than P
position (ON)” judged from the park switch signal is dis-
played.
PIIA0291E
4 - 21
: Continuity should exist.
4 - Ground
: Continuity should not exist.
LIIA1774E
SE-76
AUTOMATIC DRIVE POSITIONER
2005 Pathfinder
3.
CHECK A/T DEVICE
Check continuity between A/T device (detent switch) as follows.
OK or NG
OK
>> A/T device is OK.
NG
>> Replace A/T device.
Front Door Switch LH Circuit Inspection
EIS00466
1.
CHECK FUNCTION
With CONSULT-II
Touch "BCM" with “DOOR SW-DR” on the DATA MONITOR, check
ON/OFF operation when the front door is open and closed.
*:Refer to
.
Without CONSULT-II
GO TO 2.
OK or NG
OK
>> Front door switch LH circuit is OK.
NG
>> GO TO 2.
2.
CHECK FRONT DOOR SWITCH LH
1.
Turn ignition switch OFF.
2.
Disconnect front door switch LH.
3.
Check continuity between front door switch LH terminal 2 and ground part of door switch as follows.
OK or NG
OK
>> GO TO 3.
NG
>> Replace front door switch LH.
Connector
Terminals
Condition
Continuity
M156
4
2
P position
Yes
Other than
P position
No
LIIA1775E
Monitor item [OPERA-
TION or UNIT]
Contents
DOOR SW
DR*
“ON/
OFF”
Door open (ON)/door closed (OFF) status judged from
the front door switch is displayed.
PIIA0291E
Connec-
tor
Terminals
Condition
Continuity
B8
2
Ground
part of
door
switch
With the front door switch
LH pressed
No
With the front door switch
LH released
Yes
LIIA0948E
AUTOMATIC DRIVE POSITIONER
SE-77
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
3.
CHECK HARNESS CONTINUITY
1.
Disconnect BCM.
2.
Check continuity between BCM connector M19 terminal 47 and
front door switch LH connector B8 terminal 2.
3.
Check continuity between BCM connector M19 terminal 47 and
ground.
OK or NG
OK
>> Front door switch LH circuit is OK.
NG
>> Repair or replace harness.
47 - 2
: Continuity should exist.
47 - Ground
: Continuity should not exist.
LIIA1027E
SE-78
AUTOMATIC DRIVE POSITIONER
2005 Pathfinder
UART Communication Line Circuit Inspection
EIS00467
1.
CHECK UART LINE INPUT/OUTPUT SIGNAL 1
1.
Turn ignition switch OFF.
2.
Check signal between driver seat control unit connector and
ground, with oscilloscope.
OK or NG
OK
>> GO TO 2.
NG
>> Check the following.
●
When voltage wave form does not appear with a constant voltage (approx. 5V), replace driver
seat control unit.
●
When voltage wave form does not appear with a constant voltage (approx. 0V), replace auto-
matic drive positioner control unit.
2.
CHECK UART LINE INPUT/OUTPUT SIGNAL 2
Check signal between automatic drive positioner control unit con-
nector ground, with oscilloscope.
OK or NG
OK
>> GO TO 3.
NG
>> Check the following.
●
When voltage wave form does not appear with a constant voltage (approx. 5V), replace auto-
matic drive positioner control unit.
●
When voltage wave form does not appear with a constant voltage (approx. 0V), replace driver
seat control unit.
Connector
Terminals
Condition
Signal
(+)
(–)
P2
17
Ground
Pedal
adjusting
switch ON
(FOR-
WARD or
BACK-
WARD
operation)
PIIA4599E
PIIA4814E
Connector
Terminals
Condition
Signal
(+)
(–)
M33
10
Ground
Pedal
adjusting
switch ON
(FOR-
WARD or
BACK-
WARD
operation)
PIIA4816E
PIIA4813E
AUTOMATIC DRIVE POSITIONER
SE-79
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
3.
CHECK UART LINE HARNESS
1.
Disconnect driver seat control unit and automatic drive posi-
tioner control unit.
2.
Check continuity between driver seat control unit connector P2
terminals 1, 17, and automatic drive positioner connector M33
terminals 10, 26.
3.
Check continuity between driver seat control unit connector P2
terminals 1, 17 and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness.
4.
CHECK DRIVER SEAT CONTROL UNIT
Does the automatic drive positioner operate when the driver seat control unit is exchanged?
OK or NG
OK
>> Replace driver seat control unit.
NG
>> Replace automatic drive positioner control unit.
1 - 10
: Continuity should exist.
17 - 26
: Continuity should exist.
1 - Ground
: Continuity should not exist.
17 - Ground
: Continuity should not exist.
PIIA4598E
SE-80
AUTOMATIC DRIVE POSITIONER
2005 Pathfinder
Removal and Installation
EIS00468
Refer to
ACC-2, "ACCELERATOR CONTROL SYSTEM"
and
.
POWER SEAT
SE-81
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
POWER SEAT
PFP:87016
Schematic
EIS00469
WIWA0565E
SE-82
POWER SEAT
2005 Pathfinder
Wiring Diagram — SEAT —
EIS0046A
WIWA0566E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст