Nissan Pathfinder (2005 year). Instruction — part 283
REAR WINDOW DEFOGGER
GW-71
C
D
E
F
G
H
J
K
L
M
A
B
GW
2005 Pathfinder
3.
CHECK REAR WINDOW DEFOGGER GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between rear window defogger connector D604 terminal - and ground.
OK or NG
OK
>> Check filament. Refer to
.
●
If filament is OK.
Check the condition of the harness and the connector.
●
If filament is NG.
Repair filament.
NG
>> Repair or replace harness.
4.
CHECK REAR WINDOW DEFOGGER RELAY OUTPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between IPDM E/R connector E124 terminal 60 and ground.
OK or NG
OK
>> Replace IPDM E/R. Refer to
.
NG
>> Repair or replace harness.
Door Mirror Defogger Power Supply Circuit Check
EIS0042U
1.
CHECK FUSE
Check if the following fuse for IPDM E/R is blown.
NOTE:
Refer to
GW-58, "Component Parts and Harness Connector Location"
.
OK or NG
OK
>> GO TO 2.
NG
>> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to
GW-58, "Component Parts and Harness Connector Location"
.
- - Ground
: Continuity should exist.
LIIA0409E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
E124
60
Ground
Rear window defogger
switch ON.
Battery voltage
Rear window defogger
switch OFF.
0
WIIA0525E
COMPONENT PARTS
AMPERE
FUSE NO.
IPDM E/R
15A
43
GW-72
REAR WINDOW DEFOGGER
2005 Pathfinder
2.
CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT 2
1.
Turn ignition switch ON.
2.
Check voltage between IPDM E/R connector and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Replace IPDM E/R. Refer to
.
3.
CHECK DOOR MIRROR DEFOGGER CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R and door mirror LH or RH.
3.
Check continuity between IPDM E/R connector E120 terminal 23 and door mirror connector D4 (LH) or
D107 (RH) terminal 1.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness.
4.
CHECK DOOR MIRROR DEFOGGER GROUND CIRCUIT
Check continuity between each door mirror connector D4 (LH) or D107 (RH) terminal 6 and ground.
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace harness.
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
E120
23
Ground
Rear window defogger
switch ON
Battery voltage
Rear window defogger
switch OFF
0
LIIA2049E
23 - 1
: Continuity should exist.
LIIA2036E
6 - Ground
: Continuity should exist.
LIIA2037E
REAR WINDOW DEFOGGER
GW-73
C
D
E
F
G
H
J
K
L
M
A
B
GW
2005 Pathfinder
5.
CHECK DOOR MIRROR DEFOGGER
Check continuity between each door mirror LH or RH terminals 1 and 6.
OK or NG
OK
>> Repair or replace harness.
NG
>> Replace malfunctioning door mirror LH or RH. Refer to
.
Door Mirror LH Defogger Circuit Check
EIS0042W
1.
CHECK DOOR MIRROR LH DEFOGGER POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect door mirror LH.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror LH connector and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace harness.
2.
CHECK DOOR MIRROR LH DEFOGGER GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror LH connector D4 terminal
6 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
1 - 6
: Continuity should exist.
LIIA2038E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
D4
1
Ground
Rear window defogger
switch ON
Battery voltage
Rear window defogger
switch OFF
0
LIIA2050E
6 - Ground
: Continuity should exist.
LIIA2037E
GW-74
REAR WINDOW DEFOGGER
2005 Pathfinder
3.
CHECK DOOR MIRROR LH DEFOGGER
Check continuity between door mirror LH terminals 1 and 6.
OK or NG
OK
>> Repair or replace harness.
NG
>> Replace door mirror LH. Refer to
.
Door Mirror RH Defogger Circuit Check
EIS0042Y
1.
CHECK DOOR MIRROR RH DEFOGGER POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect door mirror RH.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror RH connector and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace harness.
2.
CHECK DOOR MIRROR RH DEFOGGER GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror RH connector D107 terminal 6 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
1 - 6
: Continuity should exist.
LIIA2038E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
D107
1
Ground
Rear window defogger
switch ON
Battery voltage
Rear window defogger
switch OFF
0
LIIA2050E
6 - Ground
: Continuity should exist.
LIIA2037E
REAR WINDOW DEFOGGER
GW-75
C
D
E
F
G
H
J
K
L
M
A
B
GW
2005 Pathfinder
3.
CHECK DOOR MIRROR RH DEFOGGER
Check continuity between each door mirror RH terminals 1 and 6.
OK or NG
OK
>> Repair or replace harness.
NG
>> Replace door mirror RH. Refer to
.
Rear Window Defogger Signal Check (With NAVI)
EIS00430
1.
CHECK AV COMMUNICATION LINE
AV communication line check is executed. Refer to
ATC-32, "CAN Communication System Description"
.
OK or NG
OK
>> GO TO 2.
NG
>> Replace display control unit. Refer to
AV-166, "Removal and Installation of Display Unit"
.
2.
CHECK CAN COMMUNICATION LINE
CAN communication line check is executed. Refer to
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> In addition, it is necessary to check CAN communication line. Refer to
.
Filament Check
EIS00431
1.
When measuring voltage, wrap tin foil around the top of the neg-
ative probe.Then press the foil against the wire with your finger.
2.
Attach probe circuit tester (in Volt range) to middle portion of
each filament.
1 - 6
: Continuity should exist.
LIIA2038E
Is rear window defogger displayed on the display?
SEL122R
SEL263
GW-76
REAR WINDOW DEFOGGER
2005 Pathfinder
3.
If a filament is burned out, circuit tester registers 0 or battery
voltage.
4.
To locate burned out point, move probe to left and right along fil-
ament. Test needle will swing abruptly when probe passes the
point.
Filament Repair
EIS00432
REPAIR EQUIPMENT
●
Conductive silver composition (DuPont No. 4817 or equivalent)
●
Ruler 30 cm (11.8 in) long
●
Drawing pen
●
Heat gun
●
Alcohol
●
Cloth
REPAIRING PROCEDURE
1.
Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
2.
Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.
3.
Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
4.
After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
SEL265
PIIA0215E
SEL012D
REAR WINDOW DEFOGGER
GW-77
C
D
E
F
G
H
J
K
L
M
A
B
GW
2005 Pathfinder
5.
Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.
SEL013D
GW-78
DOOR MIRROR
2005 Pathfinder
DOOR MIRROR
PFP:96301
Wiring Diagram — MIRROR —
EIS00433
WITHOUT HEATED MIRRORS
WIWA0536E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст