Nissan Pathfinder (2005 year). Instruction — part 377
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
PR-3
C
E
F
G
H
I
J
K
L
M
A
B
PR
2005 Pathfinder
NOISE, VIBRATION, AND HARSHNESS (NVH) TROUBLESHOOTING
PFP:00003
NVH Troubleshooting Chart
EDS001GX
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
(f
ro
n
t)
(r
e
a
r)
(f
ro
n
t)
(r
e
a
r)
(f
ro
n
t)
(r
e
a
r)
Possible cause and suspected parts
U
n
even
ro
ta
ti
on
to
rque
R
o
ta
ti
on
im
ba
la
nce
Ex
cess
iv
e
run
ou
t
Dif
fe
re
n
ti
a
l
Ax
le
Su
spen
si
on
Ti
re
s
R
o
ad
w
heel
D
ri
v
e
s
haf
t
Br
ake
s
S
teer
in
g
Symptom
Noise
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
PR-4
FRONT PROPELLER SHAFT
2005 Pathfinder
FRONT PROPELLER SHAFT
PFP:37200
On-Vehicle Service
EDS001GY
APPEARANCE AND NOISE INSPECTION
●
Check the propeller shaft tube surface for dents or cracks. If damaged, replace the propeller shaft assem-
bly.
●
Check the bearings for noise and damage. Repair or replace the bearings as necessary.
PROPELLER SHAFT VIBRATION
If a vibration is present at high speed, inspect the propeller shaft runout first.
1.
Measure the runout of the propeller shaft tube at several points
by rotating the final drive companion flange with your hands.
2.
If the runout exceeds specifications, disconnect the propeller
shaft at the final drive companion flange; then rotate the com-
panion flange 90
°
, 180
°
and 270
°
and reconnect the propeller
shaft.
3.
Check the runout again. If the runout still exceeds specifications,
replace the propeller shaft assembly.
4.
After installation, check for vibration by driving the vehicle.
Propeller shaft runout limit
: 0.6 mm (0.024 in) or less
LDIA0160E
LDIA0118E
FRONT PROPELLER SHAFT
PR-5
C
E
F
G
H
I
J
K
L
M
A
B
PR
2005 Pathfinder
Removal and Installation
EDS001GZ
COMPONENTS
Model 2F1310
REMOVAL
1.
Put matching marks on the front propeller shaft flange yoke and
the front final drive companion flange as shown.
CAUTION:
For matching marks, use paint. Never damage the flange
yoke and companion flange of the front final drive.
2.
Put matching marks on the front propeller shaft flange yoke and
the transfer companion flange.
CAUTION:
For matching marks, use paint. Never damage the flange
yoke and companion flange of the front final drive.
3.
Remove the bolts and then remove the front propeller shaft from
the front final drive and transfer.
WDIA0047E
1.
Propeller shaft tube
2.
Snap ring
3.
Journal bearing
4.
Journal
5.
Flange yoke
SDIA2046E
PR-6
FRONT PROPELLER SHAFT
2005 Pathfinder
INSPECTION
●
Inspect the propeller shaft runout. If runout exceeds the limit,
replace the propeller shaft assembly.
●
While holding the flange yoke on one side, check axial play of
the joint as shown. If the journal axial play exceeds the specifi-
cation, repair or replace the journal parts.
●
Check the propeller shaft tube surface for dents or cracks. If
damage is detected, replace the propeller shaft assembly.
INSTALLATION
Installation is in the reverse order of removal.
●
After installation, check for vibration by driving the vehicle. Refer to
PR-3, "NVH Troubleshooting Chart"
.
CAUTION:
Do not reuse the bolts and nuts. Always install new ones.
Disassembly and Assembly
EDS001H0
DISASSEMBLY
Journal
1.
Put matching marks on the front propeller shaft and flange yoke
as shown.
CAUTION:
For matching marks, use paint. Never damage the front pro-
peller shaft or flange yoke.
2.
Remove the snap rings.
Runout limit
: 0.6 mm (0.024 in) or less
LDIA0118E
Journal axial play
: 0.02 mm (0.0008 in) or less
LDIA0117E
SPD128
APD011
FRONT PROPELLER SHAFT
PR-7
C
E
F
G
H
I
J
K
L
M
A
B
PR
2005 Pathfinder
3.
Push out and remove the journal bearings by lightly tapping the
flange yoke with a hammer, taking care not to damage the jour-
nal or flange yoke hole.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
4.
Push out and remove the remaining journal bearings at the
opposite side by lightly tapping the flange yoke with a hammer,
taking care not to damage the journal or flange yoke hole.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
ASSEMBLY
Journal
1.
Assemble the journal bearings. Apply multipurpose grease on
the bearing inner surface.
NOTE:
During assembly, use caution so that the needle bearings do not
fall down.
2.
Select snap rings that will provide the specified play in an axial
direction of the journal, and install them. Refer to
.
NOTE:
Select snap rings with a difference in thickness at both sides
within 0.02 mm (0.0008 in).
SPD732
SPD131
WPD019
APD012
PR-8
FRONT PROPELLER SHAFT
2005 Pathfinder
3.
Adjust the thrust clearance between the bearing and snap ring
to zero by tapping the yoke.
4.
Make sure that the journal moves smoothly and is below the
joint flex effort specification.
SPD732
Joint flex effort
: 1.96 N·m (0.20 kg-m, 17 in-lb) or less
LDIA0119E
REAR PROPELLER SHAFT
PR-9
C
E
F
G
H
I
J
K
L
M
A
B
PR
2005 Pathfinder
REAR PROPELLER SHAFT
PFP:37000
On-Vehicle Service
EDS001H1
APPEARANCE AND NOISE INSPECTION
●
Check the propeller shaft tube surface for dents or cracks. If damaged, replace the propeller shaft assem-
bly.
●
Check the bearings for noise and damage. Repair or replace the bearings as necessary.
PROPELLER SHAFT VIBRATION
If a vibration is present at high speed, inspect the propeller shaft runout first.
1.
Measure the runout of the propeller shaft tube at several points
by rotating the final drive companion flange with your hands.
2.
If the runout exceeds specifications, disconnect the propeller
shaft at the final drive companion flange; then rotate the com-
panion flange 90
°
, 180
°
and 270
°
and reconnect the propeller
shaft.
3.
Check the runout again. If the runout still exceeds specifications,
replace the propeller shaft assembly.
4.
After installation, check for vibration by driving vehicle.
Propeller shaft runout limit
4x2
: 1.02 mm (0.0402 in) or less
4x4
: 0.6 mm (0.024 in) or less
LDIA0161E
LDIA0121E
PR-10
REAR PROPELLER SHAFT
2005 Pathfinder
Removal and Installation
EDS001H2
COMPONENTS
Model 2S1330
REMOVAL
1.
Move the A/T select lever to the N position and release the parking brake.
2.
Put matching marks on the rear propeller shaft flange yoke and
the rear final drive companion flange as shown.
CAUTION:
For matching marks, use paint. Never damage the rear pro-
peller shaft flange yoke or the companion flange.
3.
Remove the bolts, then remove the propeller shaft from the rear
final drive and A/T or transfer.
WDIA0118E
1.
Propeller shaft tube
2.
Snap ring
3.
Journal bearing
4.
Sleeve yoke
5.
Journal
6.
Flange yoke
WDIA0049E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст