Nissan Pathfinder (2005 year). Instruction — part 41
REPAIR FOR COMPONENT PARTS
AT-299
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
ASSEMBLY
1.
Install drive plates, driven plates and retaining plate in direct clutch drum.
CAUTION:
Take care with order of plates.
2.
Using a flat-bladed screwdriver, install snap ring in direct clutch
drum.
SCIA2868E
AT-300
ASSEMBLY
2005 Pathfinder
ASSEMBLY
PFP:00000
Assembly (1)
UCS003ZB
1.
As shown in the right figure, use a drift [commercial service tool:
22 mm (0.87 in) dia.] to drive instruction shaft oil seals into the
transmission case until it is flush.
CAUTION:
●
Apply ATF to instruction shaft oil seals.
●
Do not reuse instruction shaft oil seals.
2.
Install detent spring and spacer in transmission case.
3.
Install instruction shaft to transmission case.
4.
Install parking rod to instruction plate.
SCIA5259E
: 7.9 N·m (0.81 kg-m, 70 in-lb)
SCIA5248E
SCIA5716E
SCIA5220E
ASSEMBLY
AT-301
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
5.
Install instruction plate (with parking rod) to instruction shaft.
6.
Install retaining pin into the instruction plate and instruction shaft.
a.
Fit pinhole of the instruction plate to pinhole of the instruction shaft
with a pin punch.
b.
Use a hammer to tap the retaining pin into the instruction plate.
CAUTION:
●
Drive retaining pin to 2
±
0.5 mm (0.08
±
0.020 in) over the
instruction plate.
●
Do not reuse retaining pin.
7.
Install retaining pin into the transmission case and instruction shaft.
a.
Fit pinhole of the transmission case to pinhole of the instruction
shaft with a pin punch.
b.
Use a hammer to tap the retaining pin into the transmission
case.
CAUTION:
●
Drive retaining pin to 5
±
1 mm (0.20
±
0.04 in) over the
transmission case.
●
Do not reuse retaining pin.
8.
Install O-rings to servo assembly.
CAUTION:
●
Do not reuse O-rings.
●
Apply petroleum jelly to O-rings.
9.
Install return spring to servo assembly.
SCIA5715E
SCIA5297E
SCIA2427E
SCIA5719E
SCIA5717E
AT-302
ASSEMBLY
2005 Pathfinder
10. Install servo assembly in transmission case.
11. Using a pair of snap ring pliers, install snap ring to transmission
case.
12. Install D-rings in reverse brake piston.
CAUTION:
●
Do not reuse D-rings.
●
Apply ATF to D-rings.
13. Install reverse brake piston in transmission case.
14. Install needle bearing to drum support edge surface.
CAUTION:
Apply petroleum jelly to needle bearing.
SCIA5679E
SCIA2333E
SCIA6330E
SCIA2325E
SCIA2796E
ASSEMBLY
AT-303
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
15. Install seal rings to drum support.
CAUTION:
●
Do not reuse seal rings.
●
Apply petroleum jelly to seal rings.
16. Install spring retainer and return spring in transmission case.
17. Set the SST on spring retainer and install snap ring (fixing spring
retainer) in transmission case while compressing return spring.
CAUTION:
Securely assemble them using a flat-bladed screwdriver so
that snap ring tension is slightly weak.
SCIA3333E
SCIA2324E
SCIA5877E
AT-304
ASSEMBLY
2005 Pathfinder
18. Install reverse brake drive plates, driven plates and dish plate in
transmission case.
CAUTION:
Take care with order of plates.
19. Assemble N-spring.
20. Install reverse brake retaining plate in transmission case.
21. Install snap ring in transmission case.
SCIA5250E
SCIA5249E
SCIA2439E
ASSEMBLY
AT-305
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
22. Measure clearance between retaining plate and snap ring. If not
within specified clearance, select proper retaining plate.
23. Install needle bearing to transmission case.
CAUTION:
Apply petroleum jelly to needle bearing.
24. Install revolution sensor to transmission case.
CAUTION:
●
Do not subject it to impact by dropping or hitting it.
●
Do not disassemble.
●
Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
●
Do not place in an area affected by magnetism.
25. Install return spring (1) to parking pawl (2).
26. Install parking pawl (with return spring) and pawl shaft to rear
extension (2WD models) or adapter case (4WD models).
Specified clearance “A”:
Standard: 0.7 - 1.1mm (0.028 - 0.043 in)
Retaining plate:
Refer to
.
SCIA3129E
SCIA5031E
: 5.8 N·m (0.59 kg-m, 51 in-lb)
SCIA2320E
SCIA6180J
SCIA3424E
AT-306
ASSEMBLY
2005 Pathfinder
27. Install parking actuator support to rear extension (2WD models)
or adapter case (4WD models).
28. Install needle bearing (1) to rear extension (2WD models) or
adapter case (4WD models).
CAUTION:
Apply petroleum jelly to needle bearing.
29. Install seal rings to output shaft.
CAUTION:
●
Do not reuse seal rings.
●
Apply petroleum jelly to seal rings.
30. Install parking gear to output shaft.
31. Install output shaft in transmission case.
CAUTION:
Be careful not to mistake front for rear because both sides
looks similar. (Thinner end is front side.)
SCIA3423E
SCIA6179J
SCIA5209E
SCIA5247E
SCIA5030E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст