Nissan Pathfinder (2005 year). Instruction — part 235
FENDER PROTECTOR
EI-21
C
D
E
F
G
H
J
K
L
M
A
B
EI
2005 Pathfinder
Removal and Installation of Front Fender Protector
EIS00448
REMOVAL
1.
Remove screws.
2.
Remove plastic clips.
3.
Remove pushpins.
4.
Remove front fender protector.
INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation of Rear Fender Protector
EIS00505
REMOVAL
1.
Remove screws.
2.
Remove plastic clips.
3.
Remove pushpins.
4.
Remove rear fender protector.
INSTALLATION
Installation is in the reverse order of removal.
EI-22
RUNNING BOARDS
2005 Pathfinder
RUNNING BOARDS
PFP:96110
Removal and Installation
EIS00449
REMOVAL
1.
Remove mud flaps (if equipped).
2.
Remove bolts and remove running board from running board brackets.
3.
Remove nuts and remove running board brackets from chassis.
4.
Remove screw and clip and remove wind deflector.
INSTALLATION
Installation is in the reverse order of removal.
1.
Front mud flap (if equipped)
2.
Running board
3.
Rear wheel wind deflector
4.
Rear mud flap (if equipped)
5.
Running board bracket
LIIA1779E
ROOF RACK
EI-23
C
D
E
F
G
H
J
K
L
M
A
B
EI
2005 Pathfinder
ROOF RACK
PFP:73155
Removal and Installation
EIS0044B
REMOVAL
1.
Pry outward releasing the clips and remove the slide rail cover front LH and RH.
2.
Pry outward releasing the clips and remove the slide rail cover rear LH and RH.
3.
Remove the bolts and remove front and rear sliding crossbars from slide rails.
4.
Remove the bolts from the slide rails LH and RH.
5.
Shift the slide rails forward to disengage from center stanchion and remove from roof.
6.
Remove the bolts and remove center stansions LH and RH from roof.
INSTALLATION
Installation is in the reverse order of removal.
1.
Slide rail
2.
Sliding crossbar
3.
Slide rail cover rear
4.
Center stanchion
5.
Slide rail cover front
LIIA1776E
EI-24
DOOR OUTSIDE MOLDING
2005 Pathfinder
DOOR OUTSIDE MOLDING
PFP:82820
Removal and Installation
EIS0044C
FRONT DOOR OUTSIDE MOLDING
Removal
1.
Open the window fully.
2.
Remove the door mirror. Refer to
.
3.
Lift molding from the front side off of flange.
4.
Remove the front door outside molding.
Installation
Installation is in the reverse order of removal.
LIIA1780E
DOOR FINISHER
EI-25
C
D
E
F
G
H
J
K
L
M
A
B
EI
2005 Pathfinder
DOOR FINISHER
PFP:80900
Removal and Installation
EIS0044E
FRONT DOOR
Removal
1.
Remove power window switch assembly.
●
Disconnect harness connectors.
2.
Remove pull handle escutcheon.
3.
Remove pull handle cover and remove screw.
4.
Lift armrest upward to release clips and remove armrest.
●
Remove screws behind armrest.
5.
Remove memory seat switch (if equipped).
●
Disconnect harness connector.
1.
Front door
2.
Mirror bolt cover LH
3.
Mirror bolt cover RH
4.
Pull handle escutcheon
5.
Pull handle/lock lever assembly
6.
Pull handle cover
7.
Front door finisher (RH shown)
8.
Seat memory switch (if equipped)
9.
Power window/lock switch assembly
10. Armrest
11.
Front door handle bracket
LIIA1782E
EI-26
DOOR FINISHER
2005 Pathfinder
6.
Release clips and remove door finisher.
●
Disconnect lock cable and handle cable from door handle assembly. Refer to
.
7.
Remove pull handle/lock lever assembly.
Installation
Installation is in the reverse order of removal.
REAR DOOR
Removal
1.
Remove power window switch assembly.
●
Disconnect harness connector.
2.
Remove pull handle cover.
●
Remove screw behind pull handle cover.
3.
Remove pull handle escutcheon.
4.
Lift upward to release clips and remove armrest.
●
Remove screws behind armrest.
5.
Release the clips and remove rear door finisher.
●
Disconnect the rear door tweeter.
Installation
Installation is in the reverse order of removal.
1.
Rear door
2.
Pull handle escutcheon
3.
Pull handle cover
4.
Metal clip
5.
Power window switch assembly
6.
Armrest
7.
Rear door finisher
8.
Rear door handle bracket
LIIA1785E
BODY SIDE TRIM
EI-27
C
D
E
F
G
H
J
K
L
M
A
B
EI
2005 Pathfinder
BODY SIDE TRIM
PFP:76913
Components
EIS0044F
CAUTION:
●
Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from finishers.
●
When removing or installing body side welts, do not allow butyl seal to come in contact with pillar
finisher.
1.
Center pillar upper finisher
2.
Center pillar assist grip
3.
Rear door welt
4.
Rear kick plate
5.
Center pillar lower finisher
6.
Front kick plate
7.
Lower dash side finisher
8.
Clip
9.
Front door welt
10. Front pillar lower finisher
11.
Front pillar upper finisher
12.
Front pillar assist grip
13. RH side demister grille
14.
Molded plastic clip
15.
Metal clip
16. Garnish
LIIA1786E
EI-28
BODY SIDE TRIM
2005 Pathfinder
Removal and installation
EIS00507
LOWER DASH SIDE FINISHER
Removal
1.
Remove push pin from lower dash side finisher.
2.
Remove front kick plate from center pillar lower finisher.
3.
Remove lower dash side finisher and front kick plate together.
4.
Remove lower dash side finisher from front kick plate.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR LOWER FINISHER
Removal
1.
Remove seat belt anchor. Refer to
SB-3, "Removal and Installation of Front Seat Belt"
.
●
On RH side, disconnect seat belt tension sensor.
2.
Remove front and rear kick plates. Refer to
.
3.
Remove center pillar lower finisher.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR UPPER FINISHER
Removal
1.
Remove front and rear door welts.
2.
Remove seat belt shoulder anchor and D-ring. Refer to
SB-3, "Removal and Installation of Front Seat
.
3.
Remove front and rear kick plates. Refer to
.
4.
Remove center pillar lower finisher.
5.
Remove assist grip.
6.
Remove center pillar upper finisher.
Installation
Installation is in the reverse order of removal.
FRONT PILLAR UPPER FINISHER
Removal
1.
Remove the front pillar assist grip.
2.
Remove the front pillar upper finisher bolt.
3.
Remove the front pillar upper finisher.
Installation
Installation is in the reverse order of removal.
FRONT PILLAR LOWER FINISHER
Removal
1.
Remove the front and rear kicking plate.
2.
Remove the front pillar lower finisher.
Installation
Installation is in the reverse order of removal.
KICK PLATES
Removal
Release clips and remove front and/or rear kick plates.
Installation
Installation is in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст