Nissan Pathfinder (2005 year). Instruction — part 412
FRONT SEAT
SE-91
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
1.
Headrest
2.
Headrest holder with multi position
lock
3.
Seatback assembly
4.
Lumbar support lever
5.
Power seat switch escutcheon
6.
Recliner switch knob
7.
Slide switch knob
8.
Driver power seat frame assembly
9.
Leg cover
10. Driver seat wiring harness
11. Seat cushion outer finisher
12. Outer pedestal finisher
13. Seat cushion front finisher
14. Seat cushion inner finisher
15. Seat cushion frame
16. Seat cushion heating element
17. Seat cushion pad
18. Seat cushion trim cover
19. Headrest holder
20. Seatback board
21. Switch assembly
22
Seat cushion rear finisher
23
Driver instruction seat frame assembly
SE-92
FRONT SEAT
2005 Pathfinder
Passenger Seat
WIIA0469E
1.
Headrest
2.
Headrest holder with multi position
lock
3.
Seatback board
4.
Outboard reclining arm outer cover
5.
Outboard reclining arm inner cover
6.
Inboard reclining arm inner cove
FRONT SEAT
SE-93
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
REMOVAL
When removing or installing the seat trim, handle it carefully to keep dirt out and avoid damage.
CAUTION:
●
Before removing the front seat, turn the ignition switch off, disconnect both battery cables and
wait at least 3 minutes.
●
When checking the power seat circuit for continuity using a circuit tester, do not confuse its con-
nector with the side air bag module connector. Such an error may cause the air bag to deploy.
●
Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
●
After front side air bag module inflates, front seatback assembly must be replaced.
●
Front passenger seat is equipped with an Occupant Classification System sensor and control
module. Do not disassemble front passenger seat cushion assembly or remove the trim as this
will affect the Occupant Classification System calibration.
●
Always replace passenger seat cushion as an assembly.
1.
Slide the seat until the four body mounting bolts are visible and a tool can be inserted.
NOTE:
●
If disassembling the seat after removal, set the front/rear cushion lifters to the top position.
2.
Disconnect both battery cables and wait at least 3 minutes.
3.
Disconnect the side air bag module harness connector.
4.
Remove the four body mounting bolts.
5.
Disconnect the power seat harness connectors and remove the seat from the vehicle.
NOTE:
When removing and installing the seat, use shop cloths to protect the vehicle from damage.
INSTALLATION
●
Installation is in the reverse order of removal.
Disassembly and Assembly
EIS0046F
SEATBACK TRIM AND PAD
WARNING:
Removal of front side air bag module should only be done to allow deployment of front side air bag
module prior to disposal of seatback assembly.
NOTE:
Only complete seatback assemblies can be replaced.
NOTE:
Be sure to set the front/rear cushion lifter to the top position.
1.
Remove the seatback board from the back of the seatback.
7.
Leg cover
8.
Outboard reclining arm inner cover
9.
Seat cushion inner cover
10. Passenger seat wiring harness
11. Power seat frame assembly
12. Seat cushion front finisher
13. Outer pedestal finisher
14. Seat cushion outer finisher
15. Seat cushion assembly
16. Power seat switch escutcheon
17. Slide switch knob
18. Recliner switch knob
19. Seatback assembly
20. Headrest holder
21. Switch assembly
22. Seat cushion rear finisher
23. Instruction seat frame assembly
PIIA0163E
SE-94
FRONT SEAT
2005 Pathfinder
2.
Remove the retainer.
3.
Remove the headrest.
4.
From inside of the seatback, squeeze the headrest holder tabs
at the base of the stay pipe and pull the up to remove.
NOTE:
Before installing the headrest holder, check its orientation (front/
rear and right/left).
5.
Remove the snap ring and the lumbar support lever knob.
6.
Disconnect the seatback heater harness. Remove the seatback trim and pad assembly. Remove the hog
ring to separate the seatback trim from the pad and the heater unit.
REMOVAL OF SEATBACK ASSEMBLY
1.
After completing the steps 1 and 2 of "Seatback Trim and Pad", remove the side air bag harness connec-
tor from the seat cushion.
2.
Remove the mounting bolts (2 for each side) and seatback assembly.
INSTALLATION OF SEATBACK ASSEMBLY
●
Installation is in the reverse order of removal.
SEAT CUSHION TRIM AND PAD
CAUTION:
●
Front passenger seat is equipped with an Occupant Classification System sensor and control
module. Do not disassemble front passenger seat cushion assembly or remove the trim as this
will affect the Occupant Classification System calibration.
●
Always replace passenger seat cushion as an assembly.
●
When removed, the passenger seat cushion must always be placed pan side UP to prevent dam-
age.
SIIA0113E
LRS023
PIIA1156E
FRONT SEAT
SE-95
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
●
During installation, the wire harness clips must be reinstalled in the holes they were originally in.
Do not add additional clips.
●
The Occupant Classification System control module can only be replaced as part of the seat cush-
ion assembly.
1.
Remove the power seat switch knobs and power seat switch
escutcheon (or recline knobs on instruction drivers seat).
2.
Remove the front seat cushion finisher (inner).
3.
Remove the power seat switch screws (or lift knobs on instruction seats).
4.
Remove four bolts and the seat cushion assembly.
●
On the fold flat passenger seat it is necessary to unclip the
rear flap j-clip from the seat pan.
5.
Remove the retainer on the seat cushion frame, then remove the harness connector for the seat heater.
6.
On the drivers seat only, after removing the seat cushion trim and pad, remove the hog rings to separate
the trim cover from the pad and seat cushion heater unit.
LIIA0681E
LIIA0285E
SIIA0503E
SE-96
REAR SEAT
2005 Pathfinder
REAR SEAT
PFP:88300
Removal and Installation
EIS0046G
SECOND ROW OUTBOARD
Removal
1.
Lift handle and tilt seat forward.
2.
Remove seat bolts.
3.
Lower seat cushion
4.
Remove seat base trim cover.
5.
Remove seat nuts and assembly.
Installation
Installation is in the reverse order of removal.
SECOND ROW CENTER
Removal
1.
Tilt the seat cushion forward.
2.
Remove the seat cushion bolts and assembly.
3.
Remove the seat back bolts and assembly.
Installation
Installation is in the reverse order of removal.
THIRD ROW
Removal
1.
Remove the lower base trim covers.
2.
Remove front anchor bolts.
3.
Retract the seat into the cargo floor position.
LIIA1119E
WIIA0618E
LIIA1029E
REAR SEAT
SE-97
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
4.
Remove the rear anchor bolts from the seat assembly.
5.
Remove the seat assembly.
Installation
Installation is in the reverse order of removal.
LIIA1028E
SE-98
REAR SEAT
2005 Pathfinder
Disassembly and Assembly
EIS0046H
Second Row Outer
WIIA0470E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст